About Macneacail

Macneacail · 2024-01-01

I have finally isolated an example of the error. The MKI 210 accelerometer + the test board is sitting attached to a NUC computer. The entire setup has run for months with no problems at a REMOTE LOCATION that is very hard to get to without a lot of...

Macneacail · 2023-02-04

One of the critical measurements for the analysis of bridges is the thermal response. The 201/109 combination has an average thermal response in the FFT of 1.5 milli-g - it is slightly frequency dependent, but ignoring that the standard deviation mea...

Macneacail · 2023-02-04

I have about 10 of these devices on about 6 computers, so this problem is common, the device runs at about 1200 to 1400 Hz. The picture shows a temperature, frequency and FFT results plot for one device. The typical is about 1400 +- 50. I take and...

Macneacail · 2023-02-04

Macneacail · 2023-02-04

Reset does not work.

Macneacail · 2024-01-02

Thanks for the post. I can get one. One has an accelerometer from ST.com. You want to put it on a bridge, bridges are long and have remote power, it is easiest to run POE and ethernet than deal with USB, one needs a ethernet connector for the remot...

Macneacail · 2023-04-14

Thank you for your response. I am trying the zon dbrest inside a catch block in C#, we shall see if that works. All of my devices are now deployed and so I do not have a test device at the moment. I am running the devices at 1666 Hz as the theoreti...

Macneacail · 2023-04-07

I also use a serial monitor to check the data flow.

Macneacail · 2023-04-07

Yes, it is a C# program. *zon and *dbreset do not work once it is locked, trust me I have spent months on this. I have printed and read all the manuals. It only happens on some devices and not all. That is really annoying.

Macneacail · 2023-04-07

UNICO GUI needs to be fixed by the way.

User statistics

User Activity

MEMS Board and accelerometer

Thermal response

The 210/109 combination allows for a register set to select 1666 Hz. If I run the device and do a read only, it may almost run at 1666 Hz, but if you do any real reads and analysis wanting the acceleration, time and frequency the device runs slower

The 109 hang picture from the code. This is on old NUCs, modern NUCs and DELL precision. It is completely random but annoying.

The STE-VAL MKI109 and 210 combination, will hang on the start at a zon command in C#. I have to unplug the whole device and reboot the computer, it is impossible if the computer is remote, how do you turn the device off so it is reset to only the blue

Re: MEMS Board and accelerometer

Re: The STE-VAL MKI109 and 210 combination, will hang on the start at a zon command in C#. I have to unplug the whole device and reboot the computer, it is impossible if the computer is remote, how do you turn the device off so it is reset to only the blue

Re: The STE-VAL MKI109 and 210 combination, will hang on the start at a zon command in C#. I have to unplug the whole device and reboot the computer, it is impossible if the computer is remote, how do you turn the device off so it is reset to only the blue

Re: The STE-VAL MKI109 and 210 combination, will hang on the start at a zon command in C#. I have to unplug the whole device and reboot the computer, it is impossible if the computer is remote, how do you turn the device off so it is reset to only the blue

Re: The 109 hang picture from the code. This is on old NUCs, modern NUCs and DELL precision. It is completely random but annoying.