About Maksh.1

Maksh.1 · 2022-04-02

Hi , iam trying to use spi1 pheripheral for the cortex M4 and iam using Pz0 as CLK, pz1as MISO, pz2 as MOSI, pz3 as NSS , but i tried several ways to do it by changing the kernel DTS and TF-A as well but no result , could anyone please help me how ca...

Maksh.1 · 2022-03-10

Hi , iam using STM32mp157C micro processor ,On the cortexM4 i have configured SPI 1but iam unable to transmit using HAL_SPI_Transmit(), i have done some debugging in the spi driver , i found it is always returnning the HAL_TIMEOUT from SPI_WaitOnFlag...

Maksh.1 · 2022-01-28

i have tried different frequencies , modes but no result.

Maksh.1 · 2022-01-17

Maksh.1 · 2021-12-12

Maksh.1 · 2022-02-03

Hi @Danish , iam also facing the same issue as @CJami , Analog pins by default giving me 1.65 V i have measured voltage on pins using multimeter iam getting 0V , when iam connecting 3.3V to analog pins iam getting 3.3V but when iam connecting GND t...

Maksh.1 · 2022-01-28

Hi @Peter BENSCH thanks for answering , i have installed STVP and tried to program but it only supports .hex , .s19 formats , but i have .BIN format , how can load my .BIN into STM8 RegardsAkshay

Maksh.1 · 2021-12-17

Thanks Arnaud

Maksh.1 · 2021-08-26

Thanks @LudovicR my requirement is i have a remote linux PC which i can access only through ssh , Now my question is how can i import the M4 project example present in Distribution package which present in Linux PC and modify it using Cube IDE .af...

Maksh.1 · 2021-08-25

Hi @Piranha ,@Community member My requirement is to start timer from a gpio pin (TIMx_ETR) and when gpio pin set i want to toggle the led pin using timer callback function.I have followed the instructions as you mentioned and added implementation...

User statistics

User Activity

Hi iam unable to assign spi1 pheripheral to cortex M4 on STM32MP157c

Unable to transmit data Via SPI for STM32MP157C Cortex M4

Hi, Iam trying to program stm8 MCU using stm32 cube programmer, but iam getting error as Error: No STM32 target found! . I have measured voltage on target and NRST pin both have 3.3V ,any help is appreciated.

Hi , i have created mcu firmware for stm32mp1 cortex-M4 using STM32CubeIDE, iam unable to integrate the project in distribution package of stm32mp1 and build along with linux image, can you please guide me in this

Hi , iam trying to send data from M4 to A7 using IPCC. But iam sending from M4 but unable to receive at A7. if we send data twice then iam able to get the data (like a FIFO) if you could please help me in resolving this

Re: how to pull down ADC pin?

Re: Hi, Iam trying to program stm8 MCU using stm32 cube programmer, but iam getting error as Error: No STM32 target found! . I have measured voltage on target and NRST pin both have 3.3V ,any help is appreciated.

Re: Hi , iam trying to send data from M4 to A7 using IPCC. But iam sending from M4 but unable to receive at A7. if we send data twice then iam able to get the data (like a FIFO) if you could please help me in resolving this

Re: How can we modify the project present in remote connection using STM32CubeIDE.

Re: Starting a timer on a GPIO input rising edge