About DMårt

DMårt · 2024-07-24

I have tried to build my own OpenSTLinux by using the SDK and the sources, without sucess. I have been trying to compile for 2 weeks from now and I'm not very pleased over the wiki of ST32MP.Anyway. I have to show a bug. I cannot build an OpenSTLinux...

DMårt · 2024-07-24

I have installed OpenSTLinux SDK + Sources (linux, tf-a, u-boot, optee-os) on a STM32CubeIDE project.I have compiled optee-os for my custom board, but it did not work so well for tf-a.What can be wrong here?I have some issues when I need to compile t...

DMårt · 2024-07-19

I have made my own STM32MP1 board with the STM32MP151AAC3 processor. Right now I'm faceing issues with the software STM32CubeProgrammer and I don't know why this happens.My goal is to flash the eMMC via the UBS OTG. I have SDIO2 as eMMC by the way.Wh...

DMårt · 2024-07-18

I have built my own STM32MP15XXAC board from scratch DanielMartensson/STM32-Computer: STM32 Computer were Linux can be deployed onto (github.com)Instead of SD-card, it has eMMC. Now I want to flash the eMMC with OpenSTLinux. How can I do that with ST...

DMårt · 2024-06-02

Even if I route the differential pairs, one pair will always be longer than the other.Should I route an extra path, like a sawtooth or tromebone on the shortest pair to make booth differential pair equal in length?I see that the STM32MP1 dev-kit does...

DMårt · 2024-07-25

I found the solution. It was an issue when you're importing a project and migrate it to the latest version. Then you're about to facing these kind of issues.So the solution was: Create a new project and copy the parameters from the .ioc file to the n...

DMårt · 2024-07-25

@Badzonor I'm facing the same problem as you do.I think you need to configure the .dts files from STM32CubeIDE. They are generated inside the CA7 folder. They must be compiled into .dtb files. But I have problems to compile .dts and .dtsi files into ...

DMårt · 2024-07-23

Hi @PatrickF I found out that the STM32CubeIDE is generating .dts in the DeviceTree folder.STM32-Computer/STM32CubeIDE/STM32-Computer/CA7/DeviceTree/STM32-Computer at main · DanielMartensson/STM32-Computer (github.com) So right now I'm compiling the ...

DMårt · 2024-07-23

Do you think this number has to do with PZ4 and PZ5 pins? If I change this base address to another base address for the PF14 and PF15 pins. This might work? @PatrickF

DMårt · 2024-07-23

@PatrickF Ok. I will give Buildroot another chance again.As I understand. CubeIDE cannot be used to generate a device tree. CubeIDE is only made for barebone programming. Or do you mean that the CubeIDE should generate the .tvs files? When I compiled...

User statistics

User Activity

Cannot build an OpenSTLinux Project in STM32CubeIDE

Label or path X_pins_y not found - Compiling the TF-A firmware

STM32CubeProgrammer on timeout for STM32MP1

How do I flash OpenSTLinux onto STM32MP151 with eMMC by using STM32CubeProgrammer?

Should I use length matching on all differential pairs?

Re: Cannot build an OpenSTLinux Project in STM32CubeIDE

Re: STM32MP157 custom board TF-A SDMMC init failed

Re: STM32CubeProgrammer on timeout for STM32MP1

Re: STM32CubeProgrammer on timeout for STM32MP1

Re: STM32CubeProgrammer on timeout for STM32MP1