About GBehe

GBehe · 2021-02-16

I have a custom board having STm32WBCE on it. I have tried to call a function in stead of using in while (1)(Which I used to call in it and was working fine), implemented using sequencer + timer server in a repeated fashion which I create and start ...

GBehe · 2020-11-06

Hi, I have STM32WB55CE chip and want to use stop mode or any other low power mode along with BLE + sequencer active. I tried to implement stop mode in while 1 outside sequencer. But it does not work. If I enable the LPM mode in BLE configuration part...

GBehe · 2020-08-19

I have my custom STM32WB55CE board. I had programmed the example code "EEPROM_Emul" from"X-CUBE-EEPROM_V2.0.0" package on it. It was working fine. Then I did FUS upgrade with BLE full stack binary programming on it. After that, the same EEPROM emulat...

GBehe · 2020-04-30

I am a first time user of ST microcontrollers. I had just selected the MCU, and with (or) without even configuring anything in STMcubeMX, after generating the project, I got quite a numbers of the above kind of error messages. I did not write anythin...

GBehe · 2019-09-20

Hi,I am working on CMWX1ZZABZ-078 module and I use the "X-CUBE-SFOX Expansion Package" stack for Sigfox. My Queries are as below:-1) How can I get MAC ID of the Radio Device using Sigfox stack? Is there any API available?2) It is mentioned i...

GBehe · 2021-02-08

Hi,I have also similar issue on my custom board. It used to do BLE advertisement, able to connect to the ST BLE sensor application and other applications also. It used to send data also. And all of a sudden it stopped BLE advertisement. Its GPIO, tim...

GBehe · 2021-01-04

Hi Adam.In a function(eeprom_emulation()), I am initializing the EEPROM emulation followed by doing HAL_FLASH_Unlock() and then I am doing write operation and read operation in a for loop with multiple addresses/locations. Then I do HAL_FLASH_Lock()....

GBehe · 2020-12-30

This is my linker file where I set the start address of my application after OTA application. As this kind of files are not supported here to upload I made it a notepad file.Thank you..

GBehe · 2020-12-30

Hi Adam,I am doing good now.I use STM32Cube IDE. I could find out the code size at Build analyzer. Its showing 156.21KB (35.5%).I could also figure out the space available for EEPROM emulation, by opening STM32CubeProgrammer. I am looking at the flas...

GBehe · 2020-12-29

Ok. I will try with the build version file of BLE_Ota program and also I will check the STM32CubeIDE User guide.Thank you.

User statistics

User Activity

Does sequencer and timer server togather effect USB operation? Also I am unable to set the timer server TIMEOUT value to repeat the task continuously.

Can Stop mode or any low power mode be used with BLE with Sequencer (present in While(1))?

How to use the EEPROM emulation example code "EEPROM_Emul" from"X-CUBE-EEPROM_V2.0.0" package on a custom STM32WB55CE board.

What is the reason of getting error: "selected processor does not support 'dsb 0xf' in Thumb Mode" in Atolic Studio 9.1.0, when any controller is selected in STMCubeMX5.6.0?

How can we get Unique Device_ID for STM32L082 MCU present inside CMWX1ZZABZ-078 module using "X-CUBE-SFOX Expansion Package" stack for Sigfox?

Re: STM32WB BLE not working

Re: How to use the EEPROM emulation example code "EEPROM_Emul" from"X-CUBE-EEPROM_V2.0.0" package on a custom STM32WB55CE board.

Re: How to use the EEPROM emulation example code "EEPROM_Emul" from"X-CUBE-EEPROM_V2.0.0" package on a custom STM32WB55CE board.

Re: How to use the EEPROM emulation example code "EEPROM_Emul" from"X-CUBE-EEPROM_V2.0.0" package on a custom STM32WB55CE board.

Re: STM32WB Debug OTA application