About AndrewSibiryack

AndrewSibiryack · 2022-04-19

Hi!How to make a project with a motor in the "speed control" mode without using Hall sensors, but using an incremental encoder. With a simple replacement in the "MotorControl Workbench", the properties of the motor and the properties of the speed sen...

AndrewSibiryack · 2022-04-19

Hi!There is such a document: "AN5464-Positional control of a three‑phase motor with permanent magnets using X-CUBE‑MCSDK or X‑CUBE‑MCSDK-FULL"It describes the method of setting the PID controller. It is necessary to reset all coefficients and gradual...

AndrewSibiryack · 2022-04-16

Hi!There is such a document: "AN5464-Position control of a three-phase permanent magnet motor using X‑CUBE‑MCSDK or X‑CUBE‑MCSDK-FULL"It describes the method of setting the PID controller. It is necessary to reset all coefficients and gradually incre...

AndrewSibiryack · 2022-04-10

Hi!Help!When creating a position control project in the MC SDK using NUCLEO-F446RE and X-NUCLEO-IHM08M1-3Sh when compiling to KEIL, an error occurred.It is not clear where the value of SPEED_LOOP_FREQUENCY_HZ is defined.Thank you in advance!

AndrewSibiryack · 2022-04-07

AndrewSibiryack · 2022-05-03

Hello!on your recommendation, I changed the cutoff frequency to 2000 with different PID coefficients. The engine has a primary starting push and remains braked with zero speed and strong heating. What else can be done? What is the difference between ...

AndrewSibiryack · 2022-04-29

Dear GMA! After changing the coefficients according to your recommendation, the power consumption increased and there was a clear starting push. I checked the speed signal on the board before entering the microcontroller with an oscilloscope! I check...

AndrewSibiryack · 2022-04-28

Hello,I did as you asked! the motor is not rotating! I am sending you the PID controller configuration form. Maybe this will help!

AndrewSibiryack · 2022-04-27

I am forwarding!

AndrewSibiryack · 2022-04-27

I can archive the entire project and send IT to YOU! To do?

User statistics

User Activity

Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.

Hi! I can't adjust the PID controllers! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Motor PL57BLF01.

There is such a document: "AN5464-Position control of a three-phase permanent magnet motor using X‑CUBE‑MCSDK or X‑CUBE‑MCSDK-FULL"

It is not clear where the value of SPEED_LOOP_FREQUENCY_HZ is defined.

Hello! Where to find the description of the UART protocol for communication with the device. UART protocol generated when creating a project in the MC SDK.

Re: Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.

Re: Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.

Re: Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.

Re: Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.

Re: Hi! I can't make the engine spin! I am using NUCLEO-F446RE and X-NUCLEO-IHM08M1. Engine PL57BLF01.