About CCOLL.2

CCOLL.2 · 2022-11-23

On the SPC582B, there is only one SARADC and I would like to reduce the SW time needed for ADC conversion.I have about 15 ADC to convert and they are not contiguous.I use the SARADC in scan mode and I would like to retreive my ADC data in a buffer in...

CCOLL.2 · 2022-09-21

Using SPC582B chip with only 64 pins, the nexus interface pins will not be available.Does this mean that there are no trace possibilities ?

CCOLL.2 · 2022-09-15

Hi,I'm new in SPC5 world.I would like to use SPC5-Studio to start my project on a SPC582B product and I would like to be able to debug it.I have a probe SPC5-UDESTK that I have used to flash a project compiled with SPC5-Studio.It is not clear if I ne...

CCOLL.2 · 2022-09-15

I'm starting using SPC5 familly and I discover chips and tools.I would like to first start with a low cost solution and then (second generation of product) to have my project ASIL-B certified. I understand that I will have to go with a STM 3rd party ...

CCOLL.2 · 2022-12-13

Hi,Do you have an example of modified ADC driver ?Could you give me more details about "scatter-gather functionnality of eDMA" ?(I quickly tried to do such modification but I did not reach to modify the eDMA part to have it working)Thanks,Christophe

CCOLL.2 · 2022-09-29

Hi,To complete my question, on 64 pins chip, I agree that we have access to JTAG pins but we don't have access to the Nexus auxiliary port pins.I understand that there is the SPU HW bloc which goal is to give an interface between JTAG pins and some N...

CCOLL.2 · 2022-09-23

Hi Erwan,Thanks for your answer.In fact, I'm not aware of the JTAG feature. So, to precise my question, as we do not have Nexus pins available, will it be possible to have traces and to do code coverage and profiling with only JTAG pins?Rgds,Christop...

CCOLL.2 · 2022-09-16

Hi,Yes, on the previous project, JTAG was used to flash the board only so, I assume that it is physicaly OK.Thanks for the info about plugins, I have just installed the UDE plugin.I will check how many signals are available in the JTAG interface but,...

CCOLL.2 · 2022-09-16

Hi,Thanks for your answer.But, if I do not use a STM board (I have a prototype done by a customer), is SPC5 studio able to debug on it ?We plan to make a new project based on the same SPC582B or 4B chip and I would like to use this board to work on i...

User statistics

User Activity

I use the SPC582B chip and I would like to use SARADC on several channels. Is it possible to use DMA without contiguous channels ?

Using SPC582B chip with only 64 pins, will it be possible to use JTAG to send traces ?

If I use SPC5 studio, do I need to be on a STM discovery kip or evaluation board to be able to flash and debug a board with a SPC582B or SPC584B MCU (I have also a probe SPC5-UDESTK) ?

Does SPC5studio uses the same Low level driver as the ones under MCAL used by third party like EB Tresos studio or HIGHTEC ?

Re: How to properly read many ADC channels that are not consecutive with DMA?

Re: Using SPC582B chip with only 64 pins, will it be possible to use JTAG to send traces ?

Re: Using SPC582B chip with only 64 pins, will it be possible to use JTAG to send traces ?

Re: If I use SPC5 studio, do I need to be on a STM discovery kip or evaluation board to be able to flash and debug a board with a SPC582B or SPC584B MCU (I have also a probe SPC5-UDESTK) ?

Re: If I use SPC5 studio, do I need to be on a STM discovery kip or evaluation board to be able to flash and debug a board with a SPC582B or SPC584B MCU (I have also a probe SPC5-UDESTK) ?