About anotherandrew

anotherandrew · 2024-10-10

I am designing a product with an STM32G474CET (LQFP48 package) and would like to use the ROM bootloader with I2C; looking at AN2606 section 48.1, I see that I must use I2C2, I2C3 or I2C4 if I want to use the ROM bootloader.This is fine, but according...

anotherandrew · 2023-10-22

I have an STM32H735G-DK and a sample CAN application that is working fine. I am now trying to use the CANFD ROM bootloader in system memory but cannot get any response from it. All the jumpers and solder bridges on the DK are at their default config...

anotherandrew · 2023-08-21

I'm using X-CUBE-CRYPTOLIB v4.1.0 on an STM32H735. I'm using the libSTM32Cryptographic_CM7.a static library supplied by the crypto library.I'm running into an interesting issue where the address that the binary library is using for the CRC peripheral...

anotherandrew · 2023-05-08

Using an STM32H735G-DK (MB1520-H735I-C02), I was using the HDP_Boot/HDP_Appli examples and I think I fat-fingered the SEC_AREA_START and SEC_AREA_END addresses, setting both to the same value which effectively secures all of internal flash. Neither t...

anotherandrew · 2022-07-13

I'm a little frustrated that there isn't a "Here's ST's Time of Flight sensor offering and which sensors have which features" kind of page. The sensor datasheets themselves also do not give any real comparison data to other (pin compatible) parts.Fro...

anotherandrew · 2024-10-17

Thank you. Sadly not the answer I was hoping for, but understandable.

anotherandrew · 2024-02-06

Replying to myself here.from my other post here , the steps I took to get responses from the bootloader:# configure the CANFD driver on Linux:sudo ip link set can0 up type can bitrate 250000 sample-point 0.75 sjw 16 dbitrate 1000000 dsample-point 0.7...

anotherandrew · 2024-02-06

I accidentally accepted your answer, but in hindsight that is fine.I think your error is that you are sending a CAN FD frame with BRS (Bit Rate Switch) cleared. If you use cansend can0 000##1I think you will have more success. Please see my other com...

anotherandrew · 2024-02-06

I have finally achieved success.# configure the CANFD driver on Linux:sudo ip link set can0 up type can bitrate 250000 sample-point 0.75 sjw 16 dbitrate 1000000 dsample-point 0.75 dsjw 4 fd on# monitor the CAN bus (in a different window/tab):candump ...

anotherandrew · 2023-10-28

Thank you for the quick reply!So 250k/1M, BSR and you're not sending anything as a "wakeup" (like the ID 0x079 used in the "classic" CAN bootloader app note AN3154)? Just boot to ROM bootloader and send 0x002 with DLC=0 and you get three CAN frames ...

User statistics

User Activity

STM32G474 - ROM bootloader puts I2C on non-existent pins for LQFP48?

STM32H735G-DK, cannot get response from CANFD ROM bootloader

X-CUBE-CRYPTOLIB - how is the CRC peripheral base address set

fat-fingered SEC_AREA_START/END, JTAG gone, can I recover?

Comparison of features of various ToF Sensors

Re: STM32G474 - ROM bootloader puts I2C on non-existent pins for LQFP48?

Re: How to flash STM32H725 using FDCAN Bootloader?

Re: STM32H735G-DK, cannot get response from CANFD ROM bootloader

Re: STM32H735G-DK, cannot get response from CANFD ROM bootloader

Re: STM32H723 FDCAN BOOTLOADER PROBLEM