Solved

Hi guys, I read reference manual for STM32H745/755, where is mentioned that the both CPUs are after reset running on the same clock frequency, because they shared the same clock source and the prescalers are after reset in default state (no division of clock signal). I did stupid test in main loop with blinking LEDs driven separately (each on one core), but they are blinking with different period. I didnt set up anything else, interrupts are not allowed but I cant find the reason of different LEDs blinking period.Thanks a lot for advices!

When I used the STM32CubeMX for the NUCLEO-H743ZI, there's an option to enable NVIC EXTI line[15:10] interrupts for the push button. But when I used the STM32CubeMX for the NUCLEO-H743ZI2 there's no option to enable the EXTI line[15:10] interrupts for the push button. Is this a bug with the STM32CubeMX?

Currently, we are testing whether smoke and fire will occur when adjacent I/O ports are shorted. If the internal structure is the same, we think that a representative set of tests is sufficient. However, if the internal structure is different, then all I/O ports must be tested.Is the I/O port of the STM32F429VET the same from this point of view?

I am adding NFC configuration and energy harvesting capabilities to a product using the M24LR04E-R EEPROM. I purchased the M24LR-Discovery kit so that I could use the transceiver in a proof of concept before developing something on a larger scale. I have played around with the M24LRxx Application to read and write data to the EEPROM, and everything works well. I would like to develop a script in MatLab to do the same thing, before eventually implementing that in a custom windows application. I am just wondering if this is possible and, if so, how to establish communications between the transceiver and MatLab.

Hi all Can anybody help me to get documents for programming SPC584b7 with (CAN OR UART)??

..

..

..

It's working fine now.

Hello,I would like to buy a X-NUCLEO-NFC03A1 with the chip ST25R95-VMD5T. On ST website, it looks like there is two references of this evaluation board, one with the ST25R95 chip, and another one with the CR95HF chip:   I can't find a supplier for the eval board with the ST25R95 chip. Even on the ST web page, we can find only one reference:Why the nucleo with the st25r95 core is not available ?

We are trying to Rx Bulk short packet (max packet size 4 bytes) at high speed and with low software load by using the USB HOST core of OTG_FS IP mounted on STM32L476.​Prerequisite condition・I don't use the code generated by cubemx.・Host and Device connected one-to-one. (I don't use a hub)・Activated pipe is bulk-IN pipe ONLY (In steady state, excluding control pipes).・Max packet size is 8bytes.・The OTG_FS core is forced to work as a USB host-only(FHMOD@OTG_GUSBCFG = 1).・AHB CLK is 75MHz.​In implementing the above, I have some questions.​1. debounce completion interrupt (DBCDNE@OTG_GOTGINT)I'm thinking of using the DBCDNE interrupt waiting for the electrical Debounce period after port connect detected interrupt (PCDET@OTG_HPRT).​However, the Manual states that the DBCDNE interrupt will not occur unless you enable HNPCAP or SRPCAP.​Can DBCDNE interrupt not be used when the host-only mode and HNP/SRP function are not used?​2. NAK interruptTo reduce the software load, I want to IN-NAK poll

The ST62T10CB6 is an OTP but the replacement may be any chip with the same footprint. We can edit the program if it will be required.Any idea ?

Hi,I am trying to set up the fast transfer mode with the X-Nucleo-NFC04A1 board and the ST25 NFC app for android. At the moment, the mailbox management as well as writing and reading from the mailbox on the dev-board works fine.Now I want to read the data stored via I2C on the ST25DV with the smartphone. When I tap on "Start transfer" the stopwatch starts and the progress bar works, but I can't find the actual data to verify the transfer.I appreciate your help!

Hello, I have to change the EPC number of a NXP SL3S1203_1213 UCODE G2iL tag (https://www.nxp.com/docs/en/data-sheet/SL3S1203_1213.pdf). Unfortunately, this does not work on the NXP tag. I suspect that I have to do an unlock etc. before I write, but I can't figure it out. Does somebody has any idea?

I am experimenting with timers... I have a list of time values that I want to use to replay a digital signal.What I try to do is to wait for the interrupt of the base timer, then set a new period value, then wait for the next interrupt.But it seems I do something wrong.Timer inithtim6.Instance = TIM6; htim6.Init.Prescaler = 49; htim6.Init.CounterMode = TIM_COUNTERMODE_UP; htim6.Init.Period = 65530; htim6.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE; if (HAL_TIM_Base_Init(&htim6) != HAL_OK) { Error_Handler(); } sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET; sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE; if (HAL_TIMEx_MasterConfigSynchronization(&htim6, &sMasterConfig) != HAL_OK) { Error_Handler(); }Timer interupt if(htim->Instance == TIM6){   if(cmd == 1){ HAL_GPIO_TogglePin(IR_SND_GPIO_Port, IR_SND_Pin); // tried without stop/start - did not change HAL_TIM_Base_Stop_IT(&htim6); __HAL_TIM_SET_AUTORELOAD(&

Posted on June 28, 2017 at 20:56Hello all,I am having a difficulty trying to get my STM32F411E-DISCO board to go into DFU mode. After applying power to the mini USB connector (USB ST-LINK), the default program operates. I then want to go into DFU mode so I have the the power cable in the mini USB and a micro USB plugged in for the DFU and I bridge BOOT0 to VDD with a jumper and press RESET and the board will not connect to DFU. All that happens is the main demo program stops operating. Any insight as to why this is happening? I did the exact same thing on my STM32F407G-DISC1 and I can get to DFU without any issue.Any help that can be given will be greatly appreciated. Thank you in advance.#stm32f411e-disco #dfu #stm32f407g-disc1 #dfu-bootloader

I have an STM32F103 configured in slave mode using NSS for slave select and using DMA. I'm using 8 bit mode. When the master starts clocking the STM32F103 it always shifts out the first byte in the buffer twice. So rather than seeing 0xF0, 0xF1, 0xF2, 0xF3, I'm seeing 0xF0, 0xF0, 0xF1, 0xF2 shifted out and then I get the DMA transfer complete interupt.If I call it in 16 bit mode, (and I change the DMA PSIZE and MSIZE to be 16 bits as well) and do a transfer of size 2 ( to get my four bytes) it works perfectly (even though the data is transmitted little endian but I expect that)I've read a whole bunch on this today but not much turned up so I expect it is something I'm doing. I don't really want to use 16 bit transfers as I would have to massage the data so it's in big endian format when tranmitted which wouln't be acceptable.I've also tried 8 bit mode but leaving PSIZE and MSIZE as 16 bits and it shifts out 0xF0, 0xF0, 0xF2, 0xF3.Any ideas?

Hello, I am working with ST25RU3993 Reader and kit's Antenna. Initially, the Reader was able to detect different Tags using different Antennas. Then, by placing the antenna below a wood surface and tags above the wood surface, the ST UHF Reader was not able to detect any Tags. Later, even at normal conditions (without wood and placing all in a plain surface without any interruption) the Reader did not read any Tags, which worked fine before the above told setup made. I feel the Reader is damaged but not Antenna or Tag. Even after updating ST Reader with new ST Firmware Version 2 and ST GUI Version 2, the Reader did not read any Tags. Byconnecting ST Reader with ST GUI, the LEDs (MCU OK, PLL OK, OSC OK, D16/17, EXT_PA, Tuning, Tuned, RF ON) Turns ON but there is NO TAG RESPONSE. Booting or Reseting or Antenna Tuning neither did not work. I would like to know where the problem is. Is it with ST Reader, which can not read between Woods?Kindly help with the same.Thanks.

Hello,I have a strange problem on an STM32G071. I get ADC values every 25 ms from ADC1 channel 0 to 3 without DMA as speed is no issue. Strangely when one of the canels reaches about 1.2 V the CPU sometimes goes in a hard fault lock. There is a potentiometer connected to the channels with a voltage divider. The SCB->ICSR value is 0x00422003 (put out over a UART in the default handler). I tried to interpret it via the programming manual but I could not figure out anything. Here is my ADC functionuint16_t get_adc(uint8_t channel) // 24 µs { while((ADC1->CR&ADC_CR_ADSTART)!=0); // wait in case conversion is in progress ADC1->CHSELR = (1<<channel); // set channel while((ADC1->ISR&ADC_ISR_CCRDY)==0); // wait for channel changed while((ADC1->ISR&ADC_ISR_ADRDY)==0); // wait for ADC ready ADC1->CR |= ADC_CR_ADSTART; // start the conversion while((ADC1->CR&ADC_CR_ADSTART)!=0); // wait for conversion finish

..

The following upgrades for scrollers (bugs + performance) will be a part of the upcoming 4.14.0 release, but i'm publishing them here as a patch for 4.13.0 until then.http://sw-center-st-com.s3-eu-west-1.amazonaws.com/touchgfx/TouchGFX/Patches/4.13.0/Scrollers-update-for-4_13_0.ziptouchgfx\framework\source\touchgfx\containers\scrollers\   * ScrollBase.cpp * ScrollList.cpp * ScrollWheel.cpp * ScrollWheelBase.cpp * ScrollWheelWithSelectionStyle.cpp/Martin

Even though the error message in the Designer indicates that an image file name can begin with an underscore, the TouchGFX Designer is complaining about it:This might be something you may want to look into.

HelloMy setup contains an STM32H743 with a camera attached via DCMI interface.I am trying to acquire single snapshot, but unfortunately experiencing errors. I declared the following variable on my SRAM#define BUFF_SIZE (160*120) ALIGN_32BYTES(uint8_t frame_buff[BUFF_SIZE]);the variable is allocated in the AXI_SRAM region (0x240....)i also defined the MPU MPU_InitStruct.Enable = MPU_REGION_ENABLE; MPU_InitStruct.Number = MPU_REGION_NUMBER0; MPU_InitStruct.BaseAddress = D1_AXISRAM_BASE; // (0x24000000) MPU_InitStruct.Size = MPU_REGION_SIZE_512KB; MPU_InitStruct.SubRegionDisable = 0x0; MPU_InitStruct.TypeExtField = MPU_TEX_LEVEL0; MPU_InitStruct.AccessPermission = MPU_REGION_FULL_ACCESS; MPU_InitStruct.DisableExec = MPU_INSTRUCTION_ACCESS_ENABLE; MPU_InitStruct.IsShareable = MPU_ACCESS_NOT_SHAREABLE; MPU_InitStruct.IsCacheable = MPU_ACCESS_CACHEABLE; MPU_InitStruct.IsBufferable = MPU_ACCESS_NOT_BUFFERABLE;and the DCMI's DMA intialized with /* DCMI Init */ hdma_dcmi.Instance =

Hi, everyone.I have found a bug in my code resulting division by zero (float).We get hard fault if we try to divide an integer number by zero. So how does this process work for float numbers? I have tried this code and result is very strange. MCU hangs. After WDT reset, i see Bus Fault has been triggered.float a, b, c; c = 0; a = b / c;We are using STM32F746 with STM32CubeIDE. SDMMC(FatFS) , Ethernet, FMC, 4 Timers are enabled. One of these timers generates interrupt on every 250uS.My questions are:How division-by-zero in float numbers affects the MCU?Is it possible to get a trap for this operation?Thanks in advance.

Hi,Is there a way to disable PLLs at all from the clock tree editor?If I change macro definition: SPC5_ME_DRUN_MC_BITS in clock_cfg.h, it is obviously restored when generating the application again ("Generate SPC5 Application" button in toolbox).Would you have any advice for this?Good day,Yannek