Solved

Posted on June 20, 2017 at 14:08Hi All,I am new to this domain. I am using STM32F103C8 controller and has some proprietary OS on it.My objective is:1. To understand aspects(Hardware, Software, Tools, Memory etc) to be considered to add new OS.2. To remove existing OS and port Free RTOS and board bring-up.3. Confirming all the required interfaces are up and running.Thanks in advance.Kedar

Posted on June 24, 2017 at 03:15I use STM32F030C8T6,found TIM6 no interrupt.Check startup_stm32f030x8.s,there no TIM6_IRQHandler.I add it,Is that correct? 

Posted on June 26, 2017 at 14:52HiIs there any form of user guide/README.txt for how to create filesystem images using STMicroelectronics\OTA-Images\FS\utils\bin\Windows\CreateFS  (dir2img.bat)I've previously used httpd_gen.exe and gen.bat for filesystem images for the SPWF01 - can these still be used for the SPWF04?

Posted on May 31, 2017 at 03:52Hello.I seem to have a hardfault exception problem and it doesn't make sense to me.I am using ThreadX and it has to do with how long it takes to startup.So here is my startup code:/* Enable I-Cache-------------------------------------------------------------*/ SCB_InvalidateICache(); SCB_DisableICache(); SCB_EnableICache();/* Enable D-Cache-------------------------------------------------------------*/ SCB_InvalidateDCache(); SCB_DisableDCache(); // SCB_EnableDCache();// enable Usage-, Bus-, and MMU Fault SCB->SHCSR |= SCB_SHCSR_USGFAULTENA_Msk | SCB_SHCSR_BUSFAULTENA_Msk | SCB_SHCSR_MEMFAULTENA_Msk;platform_init_system_clocks(); platform_init_mcu_infrastructure();my_wiced_init(); // setup wiced uart callbacks, MUST be before platform_init_external_devices() platform_init_external_devices(); // inits gpio and serial /* Initialize all configured peripherals */ LocoGPIOInit(); MX_QUADSPI_Init(); nvram_init();/* Enter the ThreadX kernel */ tx_kernel_ent

Posted on June 23, 2017 at 16:05Hello,I use the CPU STM32F765.I want to use DMA2 to transfer ADC-results into memory.This works fine if I use DTCM-Memory for the destination  (128kbyte  from 0x20000000 to 0x2001ffff)If I use SRAM1, DMA seems to work (I get transfer complete interrupt, ADC registers indicate that adc-values were read), but no data is in the programmed addresses.Is it possible that ADC to DMA transfer only works when DTCM memory is used  for the destination?Some time ago I maybe had a similar problem: I use Keil Middleware to implement a file system using an SD-card. It started to work after I told the middleware to use memory buffers at 0x20000000.In the reference manual I read about DMA that it can address the complete memory range.If it is required to specify DTCM memory for peripheral to memory transfers: where is this documented?If SRAM1 should also work: What could be the reason why DMA works with DTCM, but not with SRAM1?Thank you.

Posted on June 24, 2017 at 02:22 Hello, I think variation of this question has been asked a couple of time, but i'm trying to understand why what I am writing is not working. Because I want to get some experience with the HAL librairies I got myself a NucleoF446RE and an accessory shieldwith a P9813 LED Driver. I also found this code that I am modifying to use HAL: https://codebender.cc/library/ChainableLED#ChainableLED.cpp. I think my problems come from my micro seconds delay function. I used the Cube to generate the base code but here is what pertain to Timer3 : MX_TIM3_Init(); HAL_TIM_Base_Start(&htim3); static void MX_TIM3_Init(void) { TIM_ClockConfigTypeDef sClockSourceConfig; TIM_MasterConfigTypeDef sMasterConfig; htim3.Instance = TIM3; htim3.Init.Prescaler = 84; htim3.Init.CounterMode = TIM_COUNTERMODE_UP; htim3.Init.Period = 0xffff;//Full 16bit htim3.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; if (HAL_TIM_Base_Init(&htim3) != HAL_OK) { Error_Handl

Posted on June 24, 2017 at 12:51 I need to vary the frequency and duty cycle of a pwm using stm32f Inside the 'pulse finished' pwm callback i've tried the following code HAL_GPIO_WritePin(LED5_PORT, LED5_PIN, GPIO_PIN_RESET); //tentative 1 //TIM9->ARR = round(value); //TIM9->CCR1 = round(value) * 0.2; //tentative 2 //htim9.Instance->ARR = round(value); //htim9.Instance->CCR1 = round(value) * 0.2; //tentative 3 int *point = (int *) (TIM9_BASE + 0x2C); *point = round(value); int *point1 = (int *) (TIM9_BASE + 0x34); *point1 = round(value) *0.2; HAL_GPIO_WritePin(LED5_PORT, LED5_PIN, GPIO_PIN_SET); In all the 3 cases if i measure with an oscilloscope the amount of time that passes between the ON/OFF state of the LED5 the value is 6us. The ON/OFF state alone is 500ns. I get the Update event thing and it is not a problem but this means that i'm waiting 5.5us for my function to return just for assigning those two register and so i'm limited in term of performance. It

Posted on June 24, 2017 at 19:07I am using cubemx v4.21.0. and the freertos version is 8.2.3. & the cmsis-rtos version is 1.02.I am using the examples of STM32F413ZH-Nucleo in stm32cube F4 v1.16.0 , when I download the program. It works wrong!I found the issure  herestatic void SemaphoreThread2(void const *argument){....for (;;) { if (semaphore != NULL) { /* Try to obtain the semaphore */ if (osSemaphoreWait(semaphore , 0) == osOK)If I use if (osSemaphoreWait(semaphore , osWaitForever) == osOK)  instead,It works fine!Could anyone tell me why  if (osSemaphoreWait(semaphore , 0) == osOK) works wrong?#um1722 #freertos-stm32cube

Posted on June 20, 2017 at 18:31Have an STM32415RG chip and would like an example using Timer1 blinking an LED on PA8 using either PWM or alternating.#timers

Posted on June 23, 2017 at 13:34Hello. I'm having problem with USART6 (again). So I'm testing now UART7. By checking documentation I have found that it is theoretically possible to set up uart7 on analog pins. I have made such conclusion after looking at p.21 of Discovery User Manual and by looking of p.76 of MCU User Manual:MCU PINDISCOVERY CONTACTPF10 : GPIO candidate (useful!)A1PF9 : UART7CTSA2PF8 : UART7RTSA3PF7 : UART7TXA4PF6 : UART7RXA5I'm confused because contacts A1-A5 are marked as analog and they are hooked to Alternative Functions related to Analog-to-Digital-Converter (in Discovery User Manual). (I'm new with electronics and I'm afraid to damage the Board)UART7 requires digital signals, I suppose.Is it OK to use these Discovery contacts for UART7?#stm32f746-discovery #uart #usart6

Posted on June 09, 2017 at 08:41Hi All,I am currently working on migrating a system from a EFM32 ARM Cortex-M3 to the STM32L476VGT ARM Cortex-M4. In the current hardware implementation, the processor is connected to asynchronous SRAM via an FPGA  that acts as an address latch (among other things). The following is an excerpt from the EBI (The external memory controller on the EFM32 Gecko chips) application notes explaining the workings of the current SRAM hardware connection.'The data bus width of the EFM32 EBI is 16 bits. When multiplexing the address and data bus, these 16 signal lines are first used for putting out the least significant 16 bits of the address, which are then held by the external address latch. Then these 16 signal lines are either used for 16 bits of data, or 8 bits of data and the remaining 8 bits of the address. See Figure 2.1 (p. 5) for an overview of the signals and address latch needed for multiplexed operation. The rest of the control signals are th

Posted on June 22, 2017 at 17:28Hello fellow Ethernet explorersI am currently trying to make a UDP connection between a stm32f4 discovery board and a pc.I have already made an example work and I am now trying to replicate the result but with a program made from scratch.When trying to build, the IDE tells me that the define ''MEMP_UDP_PCB'' is unknown.The error appears twice in the udp.c file.I have tried searching other reference in my project and have found none.Does anyone know what value should this be defined to? It's used in  udp_new() and udp_remove() functions more specifically it's used for: pcb = (struct udp_pcb*)memp_malloc(MEMP_UDP_PCB) and : memp_free(MEMP_UDP_PCB,pcb) Any help is much appreciated.-Andy#lwip #ethernet

Posted on June 21, 2017 at 12:47Hello, I'm working with a proprietary board using a stm32f107 and I would like to flash my soft into the ship by using RS232. To do that I have a RS232 connector which can be connected to USB and then I can collect Rx,Tx and GND from the DB9 connector. My trouble is when i'm trying to flash my soft with Flash Loader Demonstrator, I'm receiving this error : 'No response from the target, the Boot loader can not be started. Please, verify the boot mode configuration and the flash protection status, Reset your device then try again...'.I connected the Rx and Tx from the DB9 to the Tx and Rx of the stm32f107 (Rx->Tx, Tx->Rx), all my power supplies seems good and I did put the BOOT0 pin to GND to enter in the boot mode. I even try on an other board in case the first one was defective.Please does someone have an idea about how to solve the problem ? Did I missed a configuration ? It should be easy to flash a soft on this board, maybe I just mis

Posted on June 20, 2017 at 00:07 I've been working on a board based on the STM32F3 with a large number of ADCs and other peripherals. I'll also be using multiple I2C and UART peripherals; the responsiveness of I2C and UART is much higher than the ADCs so I have to reserve DMA usage for I2C and UART. Due to the above restriction, I planned to use the Single ADC Conversion interrupt to manually store the results of conversions. After implementing this I ran into an issue caused by HAL not respecting by choice of End of Conversion Selection: In my Initialization code, all four ADCs were configured with handle.Init.EOCSelection = ADC_EOC_SINGLE_CONV;�? After running into issues I traced the source of the problem back to lines ~2074 of stm32f3xx_hal_adc_ex.c: They Are: /* Enable ADC end of conversion interrupt */ /* Enable ADC overrun interrupt */ switch(hadc->Init.EOCSelection) { case ADC_EOC_SEQ_CONV: __HAL_ADC_DISABLE_IT(hadc, ADC_IT_EOC); __HAL_ADC_ENABLE_IT(h

Posted on October 08, 2016 at 16:08hi every onei am working on the digital light dimmer. i control my ssr by stm32f1.i have big problem.i want design the circuit that protect ssr(triac) when load will be short so that ssr not damage.but  any method that i know can not  hep me.this topic should be in other group such as power electronicbut if any body know the my question please help me.

Posted on June 14, 2017 at 14:46 Hi, I'm evaluating some flash functionalities of the STM32F469NI. I have configured the Sector 12 of my STM32F469 Flash (2MB) with a Write-Protection. When I debug my Firmware I see that the corresponding bit gets set in the FLASH_OPTCR1 Register. I also run a test when I initialize my Flash Driver which only writes a word (32bit) into the beginning of Sector 12 (0x08100000). Now there should be an error in the SR of the Flash Module. But I don't see anything here. So I tried to rise an other error and wrote a half word into a word-configured Data Register. Now I got an Error. But why do I not get any error when writting into a Write-Protected area? Did I misconfigure something? I don't see anything else in the UserManual. Here is my code enReturn_t HAL_UserFlash::setWriteProtection(void) { enReturn_t errorCode = RET_ERROR; HAL_StatusTypeDef status = HAL_OK; //FLASH_OBProgramInitTypeDef flashInit; kprintf(0,'%s...\n',__FUNCTION__); /*Unlo

Posted on June 19, 2017 at 15:26On a STM32 F777 I am configuring TIM4 to read Hall sensors (HAL_TIMEx_HallSensor_Init).I have enabled capture interrupt and in capture callback  (which is triggered at every Hall event as expected) I am clearing UIF flag (i.e. timer overflow flag).The issue is that everytime the capture callback is triggered UIF flag is always found to be one even if I measure Hall events faster than timer overflow (which is expected every 32.7 ms). With reference to the attached figure: code never breaks in line 282.Any hint appreciated.#callback #tim #clear #uif

Posted on June 19, 2017 at 07:43I am using a custom STM32L051xxx, I want to change these two programing ports to PP outputs.I think I need to DeInit them then apply the normal Init procedure, I cand see how to DeInit these ports.ThanksKevin NZ

Posted on June 18, 2017 at 20:17Hello,i'm using stm32f103c8t6 and IAR as IDE and recently I was no longer able to to load the code using IAR, as error message i had 'Fatal error: ST-Link, no MCU device found '.and when i use STM32 ST-LINK Utility i can acces to the MCU and i can erase the flash (in order to connect the the stm32 to the ST-LINK Utility i have to press the reset button then press connect button of the ST-LINK Utility then release the reset button of the MCU )can anybody help fix that please and thank you#fatal-error:-st-link #no-mcu-device-found

Posted on June 18, 2017 at 05:55Good day everyone,I'm pretty new to this.I found this MCU(http://www.mouser.co.za/ProductDetail/STMicroelectronics/STM32F765IGT6/?qs=sGAEpiMZZMs0L%252b%252bydDbPChkw%252bdkA4YC2L1vKV1WRTvavAPNGSsw2mw%3d%3d) and it would be perfect for my application, although the biggest stumbling block has been storage. I'd like to sample two signals at 1MSPS each, which it seems to be able to do. I just want to find out about storage, where are the samples stored for this MCU, through the DMA into RAM or flash? Finding an MCU with sufficient storage and write speeds has been impossible. ALso is there an evaluation board available for this MCU?  The length of data storage will be around 10 milliseconds and in the upper 200 Kb data rangeThanks in advance

Posted on June 16, 2017 at 15:24Hiwhen an interrupt kicks in, th current context (core registers , pc and so on are saved). Where in a cube generated project, would I find the context save and restore part? Which registers need to be saved? How many cycles does it need?

Posted on June 09, 2017 at 11:23Hello,I have a weird  behavior with STM32F091RCT6 SPI Peripheral on Nucleo Evaluation Board.I want to interface with a 25LC640 SPI eeprom with 8 bits data modeWhen i want to send a byte, i see On Oscilloscope 16 clocks pulse instead of 8 !!I have tested several setting, i have the good number of pulses for 9 bits data size and more .Context :STM32F091RCT6HAL library 1.6Keil IDE & compiler : 5.06SPI2 Peripheral on Port B Pin 13,14,15 Master Mode without NSS pinSPI setup like this :void MX_SPI2_Init(void){  hspi2.Instance = SPI2;  hspi2.Init.Mode = SPI_MODE_MASTER;  hspi2.Init.Direction = SPI_DIRECTION_2LINES;  hspi2.Init.DataSize = SPI_DATASIZE_8BIT;  hspi2.Init.CLKPolarity = SPI_POLARITY_HIGH;  hspi2.Init.CLKPhase = SPI_PHASE_1EDGE;  hspi2.Init.NSS = SPI_NSS_SOFT;  hspi2.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_4;  hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB;  hspi2.Init.TIMode = SPI_TIMODE_DIS

Posted on March 23, 2017 at 14:57Hi,I am using SPC560B-Discovery EVK Board,I am facing some issue in input power can you please share the schematics of SPC560b-Discovery board,then it will be easy to me to debug the issue.---Thanks & Regards,Mujeeb 

Posted on June 16, 2017 at 09:59Hi,I have partitionned my STM32F4 memory into 2 parts :1 part, starting from the default startup address ( 0x8000004 ), and 1 part starting from a custom startup address ( 0x8004004).When running code from the 2nd part, I would like to RESET the STM32, but restart at my custom startup address instead of the default one.Is there any special way to achieve this ?Thanks.Best regards,Vincent.#stm32f4-reset

Posted on June 08, 2017 at 10:19I installed JAVA8_131 and downloaded System Work Bench v2.0, but I couldn't install it.After i run the install exe, a window showed but it said,...''The access denied''''An error occured with the bundled Japa Runtime Enviroment''''Trying to continue with some already installed...'' ''The specified path can not be found.''as like following screen shot.I tried it as x86 and x64 both. My PC is Win8.1. I have made Android phone program on the PC, so I think Java is OK.I have no idea where folder the installer looks to, and no idea what file I need.Let me know what should I do.Thank you.