Solved

Hi, I have a problem with activating USART bootloader. I use USART1. Please for details about how to going in bootloader mode. Pattern 12 in  AN2606 is super complicated for me. I use now boot pin. I put it to GND and power ON . By me MCU going in bootloader mode, software put it with J-link is not started, but STM programmer show : Activating device: KO.Please, verify the boot mode configuration and check serial port configuration. Reset your device then try again.. Please for details how to put in USART1 boot mode.    

Hello ST Community,I read in the follow post question about boot sequences for STM32:STM32H7 dual core: How to start with a busy-waitin... - STMicroelectronics CommunitySo, in the post above, I see that is explain the first three Boot order of the Table 8 of the RM0399 (I put this table below), but not the last modality: Both Cortex®-M7 and Cortex®-M4 are booting.My question is: is possible to have a explanation similar to the one in the post above, but refer to Both Cortex®-M7 and Cortex®-M4 are booting?Thanks in advance,Dino

I am using ADC + DMA + USART1 + Timer in STM32 IDE in a setup consisting of:Motor → Sensors → MCU (STM32N6) → PCI am capturing the signal received at the serial port using NanoEdge AI. I have shared screenshots of:The actual current waveform observed on the oscilloscopeThe data received through the STM32N6 MCUMy doubt is:Is there anything inside the MCU or ADC that could suppress or distort the natural sinusoidal shape of the current waveform?Note:I have converted ADC values to actual current values using a 3.3V reference.I have removed the sensor bias.I have properly accounted for sensor gain.I would like to confirm whether the MCU/ADC processing could be affecting the waveform shapeEdited to place the images in the post: 

OTP portion of FLASH is a valuable asset in some STM32 families and represents a convenient place to store things like security keys. For this, it is desirable - and, as it's part of FLASH, also quite logically expected - that setting read-out protection to any level above 1 prevents the debugger from reading it.In RM0444 Rev.5 and RM0454 Rev.5 (the current 'G0 manuals), the following text indicates that this should be the case:The following table appears to indicate the same behaviour:However, user @DAlbe.3 reported, that he was able to read out OTP using debugger, while RDP was set to Level1.This, together with the fact, that the above table has changed across RM revisions, rises questions about the OTP's security.Can ST please comment? Thanks,JW

I am using STM32H563 and using seven pins to read data, all through ADC1 with GPDMA1 Channel0 -2 Words internal FIFO. I connected all seven pins to ground, expecting to get all zeros or values close to zero, but the readings seem to fluctuate randomly.Although the ADC values do increase when connected to Vcc (>3000) and decrease when connected to ground (<2000), how can I ensure that the readings are correct? Are there any settings that I should adjust?uint16_t adcbuf[7] = {0}; HAL_ADCEx_Calibration_Start(&hadc1, ADC_SINGLE_ENDED); HAL_ADC_Start_DMA(&hadc1, (uint32_t *)adcbuf, 7); while(1) { printf("ADCBUF: "); for (int i = 0; i < 7; i++) { printf("%d, ", adcbuf[i]); } printf("\r\n"); HAL_Delay(1000); } Below is the ADC1 configuration from my .ioc file. (All ranks are configured identically, except for the channel.) Below is the GPDMA1 configuration. (Use Standard Request Mode)  

HiI recently started using STM32CubeMX on MacOS and noticed that navigating through the (sub)-folder is kind of buggy or I am doing something utterly wrong.I want to create a project inside my documents folder. But everything that is inside my documents folder is not shown in the STM32CubeMX GUI when selecting a project folder. See attached picture. Can you please attempt to recreate this? I use a MacBook Air M3 16GB/265GB, Mac Tahoe V26.2 should that matter.

Heyho,the title says it...In RM0486, 14.6.5 PLL description, page 437 / 438 I find this:Using the PLLs in fractional modePLL off ... set FRAC ... PLL onCaution: Do not update DIVN and DIVNFRAC after the PLL has been enabled.On the other hand, there are comments that some dividers can be changed on the fly.So maybe it might work? Has anybody tried? With these 4 PLLs and the great clock routing possibilities, the ability to change FRAC values on the fly with this high resolution would be a fantastic feature for synchronization, without using an external VCO. 

Hello, I made a board with an STM32F103C8T6 which uses USB.My issue is that when conecting USB (self powered or with external power) I get the following error on windows:Windows has stopped this device because it has reported problems. (Code 43) A request for the USB device descriptor failed.Things I checked:- When no USB is connected, the D+ line is pulled to 3v3, but when connecting the USB it goes down to 2.8 with 0.5v being on the resistor.- Checked continuity from USB header to A11 and A12 pins (when unpowered)- Resolder pins to ensure propper contact (Except FL1, I checked that everything else is proppery soldered, but I guess continuity is a good proxy test)- Changed MCU, USB header and FL1 for new ones in case they got damaged- Firmware was tested with a bluepill and everything worked.It's been a week with this issue, if someone know what could be happening or could give me tips to help diagnose this I'd appreciate it.Here are the schematics for that part of the board: &n

Hi everyone,  I'm looking for a way to be able to encrypt my flash on stm32g030. How do I do it? Thanks

I am trying to create a codeplug for my TYT MD-2017 handheld radio.  I have gotten to the point where the radio is listed in Device Manager under "Universal Serial Bus Devices" as "Digital Radio in USB mode" with no error icons.But when I attempt to have CPS talk to the radio it says it is disconnected.  I have been working for several days on this issue with no success.  The radio IS in DFU mode and is seen by Device Manager. I am using GD77 CPS and it's driver.  I have used Zadig to load the WinUSB driver.  Perhaps I should blow all of the GD77 stuff away and use default MD-2017 radio STM software and driver?  If so, is there any installation procedure info for this approach?Any help appreciated!  What additional info is needed?73, WhiteBeard

Hi, I'm have a trouble with UART Interrupt when using FreeRTOS.I want to receive a string buffer send from Serial Terminal ( Hercules Software ) using UART interrupt mode. But when I send data, I just receive 2 character. Ex: When I send "Resume", I just got echo back 2 line: "Rx_data:R","Rx_data:e".Has anyone else encountered this problem? Please share a solution with me.This is my call back function: void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) { BaseType_t xHigherPriorityTaskWoken = pdFALSE; HAL_UART_Receive_IT(&huart1, &Rx_data, 1); if(Rx_data == '\n') { Rx_buffer[Rx_index] = '\0'; if(strcmp((char*)Rx_buffer,"Resume") == 0) { xTaskResumeFromISR(AboveNormalHandle); } Rx_index = 0; } else { if(Rx_index < sizeof(Rx_buffer)-1) { printf("Rx_data: %c \n",Rx_data); Rx_buffer[Rx_index++] = Rx_data; } } portYIELD_FROM_ISR(xHigherPriorityTaskWoken); } 

Hi,I selected STM32H7A3ZIT6Q to use external SDRAM. However, in STM32CubeIDE under Connectivity → FMC, the SDRAM option is not available.When I select STM32H7A3ZIT6 (non-Q), the SDRAM option appears.Does the STM32H7A3ZIT6Q support SDRAM, or is this a CubeIDE limitation?Thanks.

..

Hello everyone,I'm trying to disable the TrustZone (TZEN bit) on an STM32L562E-DK development board to leave it in a completely clean state (without protections) so I can use it as a standard MCU. However, I'm encountering errors when trying to modify the Option Bytes with STM32CubeProgrammer, and I would appreciate your help.My configuration:Board: STM32L562E-DKSoftware: STM32CubeProgrammer v2.21.0Connection: Integrated ST-LINK (SWD at 8000 kHz)Current Option Bytes status (initial read):TZEN = 0x1 (Trust Zone enabled)RDP = 0xAA (Level 0, no readout protection)SECWM1_PSTRT = 0x0, SECWM1_PEND = 0x7F (Safe area defined)Screenshots of the complete configuration are attached.The problem:From the STM32CubeProgrammer graphical interface, I can modify and apply changes to almost all Option Bytes (such as safe areas or write protection) without issue. However, when I try to uncheck the TZEN box (to set it to 0) and click "Apply," I get the following errors:Error: Option Byte Programming failed

Hello!I'm trying to set up a program via STM32CubeMX. The MCU I'm trying to use is the STM32WBA65CIU6 with the SMPS Pinout.source: datasheet page 72 (https://www.st.com/resource/en/datasheet/stm32wba62ci.pdf).However this configuration seemingly isn't available in STM32CubeMX, only the SMPS_USB Version.source: STM32CubeMX with STM32WBA65CIUx chosen as MCU.There's only one MCU listed in the MCU/MPU selector. Just in case if there are supposed to be multiple.source: STM32CubeMX with search-string STM32WBA65CIU6 in commercial part number.Is there an option that I'm missing? Or will I have to address this manually in code?Thank you in advance!  

Hey guys,I am searching for RoHS/REACH records for STM32G431KBU3/STM32G431KBU6 but they're only accessible for one of the STM32G431 parts.Any of you have any pointers to how I may else obtain such documentation?

stm32_IEC_project_CM7.elf [cores: 0]Thread #1 [main] 1 [core: 0] (Suspended : Signal : SIGTRAP:Trace/breakpoint trap)0xfffffffe<signal handler called>() at 0xfffffff1HAL_TIM_IRQHandler() at stm32h7xx_hal_tim.c:3,777 0x8055b74TIM3_IRQHandler() at stm32h7xx_it.c:185 0x804a352<signal handler called>() at 0xfffffffdprvPortStartFirstTask() at port.c:267 0x8065f78xPortStartScheduler() at port.c:379 0x806608cpxPortInitialiseStack() at port.c:214 0x8065ed0   This is the error which comes suddenly. here i use tim3 as base source for the tick interrupt of task scheduler as replace of  systick. Previously this code works fine. suddenly creates issues in worked hardware itself  . after some time device works and fails randomly but same code what reason    

Hello, after some time trying to debug the PA2 pin on my Nucleo H503 I realized, by looking at the board, that PA2 goes into SB7 and SB1. Reading the manual it seems like both SB1 and SB7 must be off for USB Device to work, however, this will disable PA2 and doesn't seem to be documented in the manual for the H503 board (while there are some explicit SB configs for PA2 on the H533 board). Am I missing something?

Hello, I installed STM32CubeIDE and attempted to set up my first project as you can see in the three attachments.Based on YouTube videos, I expected to see the MCU outline so I can assign functions to the pins.  As you can see in one of the screenshots, I'm getting a message stating that "There is no active editor that provides an outline"I did the following to try and address this, with no luck...   *  Uninstalled and Reinstalled STM32CubeIDE, including manually deleting folders that were not removed by the automated removal process.  To be safe, I used a different project folder name but this didn't help.  *  Installed STM32 on a second Windows 11 laptop but saw the exact same problemI didn't bother trying older versions of STM32CubeIDE because I read in a different post that this did not solve the problem for the other user.Any help is appreciated.

SYS CONFIG =========================================== IO Supplys = 3,3V, VCORE = 2,5V regulator used, FSystem = 200 MHz Timer1 is configured for Output Compare CH1, sig 0.1MHz 50% duty expected (all necessary clk enabled) Compare SIG is routed to PK1 via alternate conf  __HAL_RCC_GPIOK_CLK_ENABLE(); GPIO_InitStruct.Pin = GPIO_PIN_1; GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; GPIO_InitStruct.Alternate = GPIO_AF1_TIM1; HAL_GPIO_Init(GPIOK, &GPIO_InitStruct); After exec of this routine, PK1(J15) pin is in floating mode (1V because of 2Meg external pull-up to supply) . Same signal routed to another port/same load with same routine is working properly  Same problem and behavior with TIM8 witch can use the same PK1 pin Note1 : if internal pull-up or pulldown added to pin conf, the pin is no longer floating, Hi(3,3V) for pull-up, Low(0,1V) for pulldown but still no signal output (input mode suppose

Hi,I am making updates to a custom PCB where I would like to add ADC functionality. My board is powered by batteries and I expect the supply voltage to fluctuate slightly and I need the ADC conversions to be accurate. The reference manual says I can use the internal Vrefint to calculate what the value of VDDA/VREF+ so that I may calculate my conversions with better accuracy. Additionally, I wanted to follow this guide (https://community.st.com/t5/stm32-mcus/how-to-use-the-stm32-adc-s-internal-reference-voltage/ta-p/621425) to understand how I may implement this in firmware.The issue I see now is that on the chip's datasheet it mentions that Vrefint is internally connected to ADC1_IN0, however, ADC1_IN0 has no pinout on this package of the chip. Furthermore, in STM32CubeMX the ADC1_IN0 channel is not able to be selected (although Vrefint channel is able to be selected).Now I have some confusion since the datasheet mentions the internal connection. Maybe this package does not have this a

On an STM32U5G7VJTX I'm using a custom board with an ILI9488 480x320 display in 16-bit mode on the FMC.I am using NemaGFX version 3.5.0 for the STM32U5x9 as I don't have STM32U5x7.Drawing lines for a test works fine as long as I skip the nema_cl_wait() function, which hangs forever.To give GPU2D time to finish the work, I replaced nema_cl_wait() with a short loop that takes enough time. But that's obviously not a good idea, as some tasks can take longer or shorter.On the STM32U5G9J-DK2 Discovery kit the same GPU2D stuff runs just fine!Is this because the GPU2D in the STM32U5G7VJTX isn't exactly the same as in the STM32U5G9ZJT6Q?I've experimented with the GPU initialization in nema_hal.c, but without solving this issue.Does anyone have any ideas?/** * @brief Draws a line * [in] x1 * [in] y1 * [in] x2 * [in] y2 * @return None */ void Draw_Line(float x1, float y1, float x2, float y2) { /* Create GPU Command List */ Display.NemaGFX.cl = nema_cl_create_sized(8192);

Hello STM32 enthusiasts,While testing NemaGFX v1.3.0 for the STM32H7RS (M7), I discovered some differences compared to NemaGFX v3.5.0 for the STM32U5x9 (M33).1. nema_clear(color); Doesn't work, I had to come up with some solution: nema_matrix3x3_t m; NEMA_VG_PAINT_HANDLE paint; uint32_t color = nema_rgba(0xFF, 0xFF, 0x00, 0xFF); /* Fill the screen with a color */ #if defined(STM32H7S7xx) /* Use this on STM32H7RS */ paint = nema_vg_paint_create(); nema_vg_paint_clear(paint); nema_mat3x3_load_identity(m); nema_vg_set_fill_rule(NEMA_VG_FILL_NON_ZERO); nema_vg_paint_set_paint_color(paint, color); nema_vg_draw_rect(0, 0, DISPLAY_SIZE_W, DISPLAY_SIZE_H, m, paint); nema_vg_paint_destroy(paint); #else /* Does not work on STM32H7RS */ nema_clear(color); #endif2. nema_bind_src_tex / nema_blit Does not work with the NEMA_AL88 format, but luckily it does work with the NEMA_ARGB8888 format.// Format = NEMA_AL88 /* Doesn't render any output using AL88 bitmaps */ Format = NEMA_ARGB88

When opening a project directory in VS Code, the STM32CubeIDE for Visual Studio Code extension gets stuck in an infinite loading state (as shown in the screenshot below).Symptoms:"Go to Definition" does not work.The Build Analyzer view does not appear. clicking the "Build" button still triggers a successful compilation.Most dependent extensions, such as STM32Cube CMake Support, remain inactiveHere is the log output from STM32Cube Core during the failed loading:I discovered that if I completely disconnect my PC from the internet before launching VS Code, the extension reports a network error but then successfully initializes after a short period. Once initialized offline, all features (including Go to Definition) work perfectly.Here are the logs from a successful (offline) launch:My computer’s network connection is working fine. I tested this URL in the VS Code command line —developer.st.com/bundles/BundleRepositoryIndex.json — and it downloads normally. I’ve tried both the latest

Hello everyone, I'm having some trouble implementing I3C communication and would like to ask for some help. I am using the NUCLEO-H503RB board as my main controller. For the target devices, I have the NUCLEO-IKS01A3 expansion board and the TSC1641 (Click Board) connected. I'm currently facing some issues with the I3C communication setup between these components. I have successfully managed to read the WHO_AM_I ID from the LSM6DSO (on the NUCLEO-IKS01A3). However, when I attempt to read the ID from the TSC1641, the SCL line continues to output a clock signal (or stays toggling) without a proper response. I am seeking assistance in analyzing the root cause of this issue.