Solved

Hello,I am using the ST25R3918 in NFC-F (FeliCa) Card Emulation (CE) mode, controlled by an MCU via RFAL (based on STEVAL-25R3916B_V2.1.0). [Issue Description]The system works correctly under normal conditions: the ST25R3918 receives commands like "Write Without Encryption" or "Read Without Encryption" from a reader and sends back the appropriate responses.However, if the reader is moved away from the ST25R3918 (resulting in RF field loss) during the communication process, the MCU firmware falls into an infinite loop. [Analysis Details]The loop occurs within the do-while block of demoTransceiveBlocking() in card_emulation.c. The call stack is as follows: rfalNfcWorker() -> rfalWorker() -> rfalRunTransceiveWorker() -> rfalTransceiveRx()Inside rfalTransceiveRx(), the state gRFAL.TxRx.state remains stuck at RFAL_TXRX_STATE_RX_WAIT_RXS. The function st25r3916GetInterrupt() is called with the following mask: (ST25R3916_IRQ_MASK_RXS | ST25R3916_IRQ_MASK_NRE | ST25R3916_IRQ

I downloaded the STM32C5 software package from st.com, but I am unable to use IAR. How can I import the CMake project?

Hello,in our design with STM32H753ZIT6 I've adjusted the C0G load capacitors on the LSE 32.768 kHz crystal so that the real-time clock is now very accurate (less than 1 second error in 24 hours). I've always performed the calibration in VBAT mode at a voltage between 2.3 and 3.2 V.However, now I've noticed that in normal VDD mode with active controller, the real-time clock is running significantly too slow, with an error of 90 seconds in 24 hours. I've ruled out the VBAT supply voltage as the cause. Any ideas what could be causing this large error in normal VDD mode?Thank you!

There is no USBX or other middleware in my cubemx2, but the connection introduction indicates that it is available. How to access middleware & utilities - STM32CubeMX2 1.0.0 documentation    

I am looking for the documents of below.How to look top marking of M24M02-DRMN6TP.How to look the label  and Tape & Reel specification. 

Hi ,Recently I got a NUCLEO-C051C8 board and tried to connect it to windows and program it using STm32CubeIDE but it does not show that st-link is connected , ST-link on board blinks RED continuously. Cant install it ( installation goes through , but cant see it in device manager ) using stsw-link009( https://www.st.com/en/development-tools/stsw-link009.html?dl=redirect ) Cant connect using STM32CubeProgrammer. Tried 2 USb cables , various ports of pc but  in vain. Can someone please help ?   

The STM32CubeIDE project output setting is not present in STM32CubeMX2. Is there a way to generate a project that STM32CubeIDE can use? How do I do this? I did try the "CMake" option but wasn't able to get a project to import correctly.

Hello i use STM32G070CBT6 with PD0 and others pins.PD0 as input pin with no internal pull-up/down with extrenal 10k pullup gives only 0.7V, when i set the pin to output and set state to high there is 3.3V.Where is the problem? 

Dear ST Community,I am currently migrating my Firmware from STM32H723VG to STM32H563VI. I have problem with Internal Temp Sensor. Based on Reference Manual on both MCU reading temperature is the same, but it doesn't work as it should.When on STM32H7 I got about 750 (24 degree Celsius) on reading ADC from TEMP Sens, on STM32H5 I have around 100.I tried both with and without cache (ICache and DCache), with Bare Metal and Zephyr RTOS code. In every configuration it is not working. I tried also on different MCUs, so it shouldn't be part itself.It worked with Nucleo H563ZI, but doesn't with H563VI.What else can I do?

According to Page 1354 of rm0394, setting LDMA_TX bit must occur only when SPE=0.However, from my reading of the function HAL_SPI_Transmit_DMA, this bit may be set or cleared when the DataSize <= 8bit and MemDataAlignment == HALFWORD, even if SPE=1.This looks like a bug.Am I correct?STM32Cube MCU Package for STM32F4 STM32L4, version 1.28.3

Hi,among probably many other registers, the ITM registers like TCR and Stimulus Port Registers described in the ITM programmers model in ARM Cortex-M7 Processor TRM are missing. Which means I either have to adapt the svd file or go to memory view and translate and modify the registers manually. Is this on purpose and or are there plans to fix this? If you have a repository somewhere I can maybe fix that on my own and start PR.Ty in advance

I am setting up my STM32F303RET6 for four differential inputs to be sampled simultaneously. As seen in the screenshot attached. there is no option for differential inputs on CubeMX. Am I missing something here? I have reset whole project to ensure no pins are assigned elsewhere.

Hi I have a USB-C Connector that will be used for Power Delivery Sink  for charging and USB Full Speed Mode(12Mbps) for communicating with onboard STM32F767ZIT6. But only one thing will happen at a time.    As seen in the attached schematics, I have used STUSB4500 as PD Sink controller. I will communicate with it via I2C using STM32. I understand that this STUSB4500 will negotiate 20V(60W which i want for charging) with the source(which in this case is AC-DC Wall adapter) in Power Delivery Mode. But my question is during USB Full Speed Mode Communication with STM32, when that USB-C Receptable is connected to a PC instead of Wall Adapter. As during charging mode, USB_VBus is 20V and in Full Speed mode, it is 5V and my STM32 is Self-Powered and VBus sensing is mandatory. But due to USB VBus varying between 5V and 20V, I cant connect it to for example PA9 VBus sensing pin of STM32 using a voltage divider.  So, i was thinking maybe there is another option to sense

Hello Everyone,I’m still getting up to speed with the STM32N6 series, so apologies if my question seems off, but I’d really appreciate your help!I’m working on implementing object tracking using the STM32N6570-DK board with the MB1854B camera. I'm wondering if it’s possible to deploy OpenCV on this platform to support the tracking logic.If anyone has experience with this or knows of any courses, guides, or resources that could help me deploy OpenCV (or similar tracking frameworks) to the board, I’d be incredibly grateful.Also, if you have relevant experience and are open to offering support or consultancy, I’m more than happy to discuss compensation. Please feel free to reach out!Thanks in advance for your time and help!

Dear ST,I am searching for  LTE module , basic data transfer is to send 2Kb of data using mqtt and perform http opeartion. I have got to know about ST87M01 LTE module, for getting started i got the evaluation board EVKITST87M01-2 i have few doubts before getting it 1) Can i use Vi, Jio or Airtel sim card with it.2) In some series it is showing esim, so does it have built-in esim or need to add it in design externally.3) can i interface ST4SI2M0020TPIFW esim with it.4) If i done with prototype with it, can i get the design and component availability for large.5) Documents for gettign started with ST87M01 and ST4SI2M0020TPIFW esim. Regards,Shubham

Hello, I tried to program a MSD on an STM32C071. My computer "sees" the USB device but didn't recognized it as a storage device. I use the NUCLEO-C071 and have setup the following: RCC:High Speed Clock(HSE): Crystal/Ceramic Resonator Clock Configuration:Input frequency: 8HCLK: 48ToUSB(Mhz) HSIUSB48: 48 CubeMX USB:Mode: Device_Only,USB interrupt enabled CubeMX USBX:UXDevice memory pool size: 1024*5USBX Device Generate Core Init code: yesUSBX Device System Stack Size: 1024*5 In CubeIDE:main.c: /* USER CODE BEGIN 2 */ MX_USB_PCD_Init(); // Line 94 /* USER CODE END 2 */ /* USER CODE BEGIN USB_Init 2 */ HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x00 , PCD_SNG_BUF, 0x20); // Line 180 HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x80 , PCD_SNG_BUF, 0x60); HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x81 , PCD_SNG_BUF, 0xA0); ux_dcd_stm32_initialize((ULONG)NULL, (ULONG)&hpcd_USB_DRD_FS); HAL_PCD_Start(&hpcd_USB_DRD_FS); /* USER CODE END USB_Init 2 */ In ux_device_msc.c /* USER CODE BEGIN P

Hello,after updating MEMS Studio to version 2.3.1 I am experiencing an issue when working with FSM configurations.Previously everything was working correctly, but now I cannot reload FSM configurations saved as JSON files.Steps to reproduce the issue:Create a new FSM in MEMS Studio.Save the configuration as a JSON file.Try to reopen the same JSON file.The file loads without any error message, but the FSM editor remains empty and the FSM configuration is not shown.However, individual FSM examples included in MEMS Studio open correctly without any issues.This happens both with:JSON files generated previously with an older version of MEMS StudioJSON files generated directly from example FSM projects in the current versionSo the issue does not seem to be related to the JSON content itself.My setup:MEMS Studio version: 2.3.1Sensor: LSM6DSOXQuestions:Has the FSM JSON handling changed in MEMS Studio 2.3.1?Is there a specific way to reopen a saved FSM configuration JSON?Is this a known issue o

I'm working on a design with an STM32L072CZT6TR, where I want to calibrate my main timebase. That main timebase is TIM6, which counts 16,000. The HSE is 16MHz, so there's an interrupt evey 1ms. Calibration is done by counting the number of HSE cycles between two consecutive PPS pulses from a GPS receiver. The PPS triggers an EXTI interrupt, which starts TIM21 and TIM22 at 0 on the first pulse, and reads the timer values on the second.TIM21 is set to count 16,000 pulses and TIM22 is slaved to TIM21. This way, I can conveniently determine whether the HSE is slow (TIM22 == 999) or fast (TIM22 == 1000), and calculate a correction based on TIM21.This logic is copied straight from an older design with an STM8, where it works like a charm. However, the cascading does not work. No matter what, TIM22 is always 0 on the second PPS. I have used CubeMX to set the timers up, and, going over the code with the reference manual as my guide, I can see no errors. Being a hardware engineer

I'm using eFuse STEF05D, found 2 version of the datasheet below which show the different formulas:STEF05_en.DM00034383,pdf: R-Limit = 65/IshortSTEF05D.pdf: R-Limit = 42/IshortCan someone help clarify which formula is correct? 

My post was deleted without any notification or reason? https://community.st.com/t5/escalated-topic/stm32h5-fdcan-system-bootloader/m-p/886189#M30060  

Hello,I’ve recently started using ST products and the IDE with CubeMX, which is why I’m asking for your help. I’ve just begun developing a communication system using a Nucleo H743ZI2; my goal is to set up a UART and a CAN bus.The UART is done; I used DMA access to optimize it. However, when I try to enable the CAN bus in Cube MX, I run into a problem with the clock configuration related to the bus.When I use the “Resolve Clock Issues” function, I get the error: “Cannot find a solution for some constraints.” Does anyone have any ideas to help me solve this problem? Thank you in advance, and have a great day,

Hi Guys,Based on some tutorials, I am trying to execute ADC module of STM8S105 and display the ADC result in 16x2 LCD display. The problem is : thousandth digit place is showing alphabetic character right from "A"  when I increase voltage on ADC channel from 0. Please see my code as well as adc.h file. I am eagerly awaiting someone to suggest where I have made the mistake.  #define LCD_RS GPIOD, GPIO_PIN_2 #define LCD_EN GPIOD, GPIO_PIN_3 #define LCD_DB4 GPIOD, GPIO_PIN_4 #define LCD_DB5 GPIOD, GPIO_PIN_5 #define LCD_DB6 GPIOD, GPIO_PIN_6 #define LCD_DB7 GPIOD, GPIO_PIN_7 #include "STM8S.h" #include "lcd.h" #include "adc1.h" main() { //Variable declarations unsigned int test_var ; char d4,d3,d2,d1; gpio_adc_init(); adc_init(); Lcd_Begin(); Lcd_Clear(); Lcd_Set_Cursor(1,1); Lcd_Print_String("STM8S103F3P3 LCD"); delay_ms(5000); Lcd_Clear(); Lcd_Set_Cursor(1,1); Lcd_Print_String("Circuit Digest"); Lcd_Set_Cursor(2,1); Lcd_Print_String("Test: "); while (1) { test_var

Hi,I have a question about choosing some fairly basic security settings for an STM32H5.We are developing a system that uses both G4 and H5 micros. We have developed a largely common bootloader that receives a signed encrypted application over variously USB, UART, or CAN, and flashes it to internal memory. This is working on the G4 and H5.For the G4, we understand that if we select "Level 1" read protection, the bootloader will still be able to erase and re-flash a new application but a user will not be able to gain access to the code (bootloader, application, or data in CC RAM). Further, the G4 can be reverted to Level 0 if required, but this will erase the proprietary code.Ideally, we would like the same security behaviour on the H5. I have been reading about the bewildering selection of security settings with privileged and secure settings for individual peripherals but I feel this is more complicated than we require. Our bootloader already prevents someone installing malicious code

Hi,I am using the latest version of STM32Cube extension for VS Code (3.8.0). I created a simple project for STM32H735G-DK board using CMake as the toolchain and ST-ARM-CLANG as the compiler. I do not know if it is relevant, but I also enabled FreeRTOS and configured the USE_NEWLIB_REENTRANT option to Enabled.I generated the project and I am compiling it with VSCode. I changed in the starm-clang.make to use the NEWLIB instead of the PICOLIBC:set(STARM_TOOLCHAIN_CONFIG "STARM_NEWLIB")The compilation works, but clangd complains about some errors. In the output of clangd, I can see multiple instances of:D:\ST\stm32cube\bundles\st-arm-clang\21.1.1+st.6\bin\..\lib\clang-runtimes\multilib.yaml:47:3: error: unknown key 'IncludeDirs' IncludeDirs: ^~~~~~~~~~~ D:\ST\stm32cube\bundles\st-arm-clang\21.1.1+st.6\bin\..\lib\clang-runtimes\multilib.yaml:21:1: error: multilib "arm-none-eabi/armv4t_exn_rtti_size" specifies undefined group name "stdlibs" MultilibVersion: '1.0' ^and because of these erro

Is it ok to use different build configuations for different pinout version?As you may have experienced, sometimes pcb version how the pinout. Sometimes another UART or TIMER is used in another pin etc,... Is it ok to  use different build configuations for different pinout version?