About thomfischer

thomfischer · 2021-10-08

CubeMx generates the following code /* Initialize all configured peripherals */ MX_GPIO_Init(); MX_RTC_Init(); MX_USART1_UART_Init(); MX_TIM5_Init(); MX_SPI1_Init(); MX_TIM14_Init(); MX_I2C1_Init(); MX_QUADSPI_Init(); MX_SAI1_Init(); MX_SAI2_Init(); ...

thomfischer · 2016-10-27

Posted on October 27, 2016 at 10:58Hello,I made a simple project with usb host msc on STM32L476G-DISCO ,The application works after reset, the usb stick is correctly enumerated.After Disconnect and Reconnect of the USB-stick ,the Enumeration of the ...

thomfischer · 2016-05-19

Posted on May 20, 2016 at 08:49When selecting I2S protocol for SAI Interface,CubeMX does not allow to modify all parameters of SAI Interface,in my case I need to change the clock Strobing for receive in SAI B to SAI_CLOCKSTROBING_RISINGEDGE,the gene...

thomfischer · 2016-05-18

Posted on May 18, 2016 at 14:18 i tried to port software from F4 to F7 but got HAL_TIMEOUT and wrong reading of data from functio n HAL_I2C_Master_Receive() i changed the following code --- stm32f7xx_hal_i2c.c Tue Dec 22 14:36:08 2...

thomfischer · 2016-04-10

Posted on April 11, 2016 at 08:51Hello, I try to download CubeMx 4.14.0 from ST Webpage, but only always get ''Sorry page not found'' I need the setup program for a restorable development enviroment.

thomfischer · 2021-03-11

Hello,the hex file is ok,i had to modify "program_hexfile.bat"it could not load the external loader file, because of the SPACE in "Program Files"1. changed the path to my programmer directory2. copy the external loader file "MX25LM51245G_STM32H735G-D...

thomfischer · 2021-03-08

Hello,freertos calls the task entry function, when it starts a task.This is the wrapper function Task1::task1Run with C-linkage (extern "C").This calls the calls the member function Task1::run of class Task1. The tasks are then running in the for(;;)...

thomfischer · 2021-03-02

use cubemx programmer,can you connect to the board over STLINK and erase it ?if not can you connect to the board over USB (CN14 USB FS) and erase it ? (set JP7 5V PWR to USB FS and switch SW1 to SYS MEM and reset)if erased you can try to program the ...

thomfischer · 2021-03-02

CubeMx 6.1.1 generates wrong code in SystemClock_Config().I had the same problem and erased the board over USB FS with cubemx programmer.(set JP7 5V PWR to USB FS and switch SW1 to SYS MEM)/** * @brief System Clock Configuration * @retval None */void...

thomfischer · 2019-06-29

1.The boot address must point to an address where there is real memory mapped to.ICP = In Circuit programming. In the flowchart Figure 46, if Boot add is "If boot address is out of memory range or in ICP", it goes to point "Continue Bootloader execut...

User statistics

User Activity

CubeMx 6.3.0 STM32H753ZITx peripherals initialization sequence bug ?

STM32L476G-DISCO USB HOST MSC Enumeration problem, STM32CUBE 4.17.0, STM32Cube FW_L4 V1.5.2

CubeMX 4.14.0 STM32 FW_F7_V1.3.1 SAI I2S Initialization problem

STM32 FW_F7_V1.3.1 I2C HAL_I2C_Master_Receive() BUG

need link to download CubeMx 4.14.0

Re: Where is STM32H735G-DK full .hex file as supplied from the factory?

Re: C++, FreeRTOS, tasks, classes, and how to make them work.

Re: STM32H735 - Error in initializing ST-Link device.Reason: (4) No device found on target.

Re: STM32H735 - Error in initializing ST-Link device.Reason: (4) No device found on target.

Re: Setting up STM32F765 for dual boot operation.