About msureshkumar2610

msureshkumar2610 · 2021-06-05

Hello All,If I pass 0x38 hex value into my function, that should be came out from my one of the port as parallel data, how to do this ? please give me a simple example with code and explanation.My youtube channelStm32user

msureshkumar2610 · 2021-05-15

/* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body *****************************************************************...

msureshkumar2610 · 2020-04-03

In my Nucleo while debugging STLINK LD1(RED and GREEN) is not blinking. I study with some of documents. it is communication error, But the debugging is is normalPlease tell me what is the problem ? Any settings to change ?I have attached the photo. N...

msureshkumar2610 · 2020-04-01

In Stm32 has too many parameters, So please some explain me how to use this ?. please watch my timer videos. because I know how to use the timer in PIC, but in stm32 which is prescalar and how to calculate for generating pulse(in expected frequency)

msureshkumar2610 · 2019-10-01

Hi, This is sureshkumar, I bought one STM32 popular udemy course, on that course have one video that trainer shows some registers to set the pin directions. but my data sheet is showing different name of the register. on that video showing MODE regis...

msureshkumar2610 · 2021-06-06

Thank you, not same port, different port pinsMy youtube channel Stm32user or Arduinoenthu recently I changed to Stm32user, so may be it will take time to reflect, Anyway I shared my channel linkhttps://www.youtube.com/channel/UCMRdTbIsDBp0sBXjrMcSWyg

msureshkumar2610 · 2021-05-16

ok Thanks, then I will check the 5v pin first, I will try once then I will come back.

msureshkumar2610 · 2020-04-04

And I have some of the questions.How do I generate 2Mhz frequency using timer. What is the timer calculation ?I got calculation like from youtube.Peripheral clock/Desired clock = value = PSC*ARRIs it Correct ?. In PIC timer(8bit) I know wellthat is ...

msureshkumar2610 · 2020-04-04

Please let me know if any other. I already upgraded using HELP-> ST LINK Upgrade in CubeIDE. But no Improvement.

msureshkumar2610 · 2020-04-04

No I did't tried yet. But I would like to stay inside only cubeide. I want to learn all the things this cubeide. It is good for me. I wont migrate from cubeide.Because already switched form KEIL(without proper use). At least I would like to learn all...

User statistics

User Activity

I want to know the parallel communication

Hello All, I interfaced buzzer with my NucleoF103RB board, schematic and code attached with this post. now the problem is my buzzer is not playing loudly and I used one loop to increment the duty cycle, it is was not playing continuously.

In my Nucleo while debugging STLINK LD1(RED and GREEN) is not blinking

Timers, How to set the timer ? In STM32 Please explain me. Watch my video I am explaining Timer multi tasking concept https://www.youtube.com/watch?v=EYXbNmaPBWo My Timer explanation in PIC 8 bit https://www.youtube.com/watch?v=dP1S4p7a1js

I need to know the register name is changes every datasheet.

Re: I want to know the parallel communication

Re: Hello All, I interfaced buzzer with my NucleoF103RB board, schematic and code attached with this post. now the problem is my buzzer is not playing loudly and I used one loop to increment the duty cycle, it is was not playing continuously.

Re: In my Nucleo while debugging STLINK LD1(RED and GREEN) is not blinking

Re: In my Nucleo while debugging STLINK LD1(RED and GREEN) is not blinking

Re: In my Nucleo while debugging STLINK LD1(RED and GREEN) is not blinking