Browse
STMicroelectronics Community
FAQs
Sign In
Product forums
STM32 MCUs
STM32 MCUs Products
STM32 MCUs Boards and hardware tools
STM32 MCUs Software development tools
STM32 MCUs Embedded software
STM32 MCUs TouchGFX and GUI
STM32 MCUs Motor control
STM32 MCUs Security
STM32 MCUs Wireless
STM32 MPUs
STM32 MPUs Products
STM32 MPUs Boards and hardware tools
STM32 MPUs Embedded software and solutions
STM32 MPUs Software development tools
MEMS and sensors
MEMS (sensors)
Imaging (sensors)
Automotive and Transportation
Automotive MCUs
AutoDevKit Ecosystem
GNSS positioning
Edge AI
Analog and audio
Interface and connectivity ICs
Power management
ST25 NFC/RFID tags and readers
STM8 MCUs
Other: hardware
Other: software
Knowledge base
STM32 MCUs
STM32 MPUs
MEMS and sensors
Analog and audio
EMI filtering and signal conditioning
Interface and connectivity ICs
Power management
Quality & reliability
Academy
About
Community guidelines
Feedback forum
Community blog
Developer news
Ocebe.1
Associate III
since
2020-11-07
2023-10-09
User statistics
14
Posts
1
Solutions
0
Kudos given
1
Kudos received
View all badges
STMicroelectronics Community
About Ocebe.1
Options
Report User
User Activity
Posts
Replies
Hello, how can I write start,stop,address and write functions for I2C Master Mode in stm32g031k8
2021-04-08
Hello, In my project when program come to this "_HAL_UART_ENABLE_IT" ,hard_fault happened What is the problem ? or what are this code ? Are there anyone help me please?
2021-03-30
Hello,I use microphone and When I talk I get the data from microphone to eeprom.I want to playback to speaker from eeprom .I think,I have to produce analog signal.But I shouldn't use DAC .How can I produce Analog signal without DAC in stm32 ?
2021-01-10
Hello,I have stm32g031k8 and I want to write and read on eeprom with registers.How Can I do that
2020-12-30
I have atmel 24c512 eeprom ,How should I do connection between board and eeprom .
Hello , I want to connect boot0 and 3.3V for reset my chip .I find boot0 pin is in PA14 but I cannot see on my board, could you help please (my board is stm32g031k8)
2020-11-08
View more
Re: Hello, how can I write start,stop,address and write functions for I2C Master Mode in stm32g031k8
2021-04-08
Thank you for your advice , I wrote a code for printf() :grinning_face:
Re: Hello, how can I write start,stop,address and write functions for I2C Master Mode in stm32g031k8
2021-04-08
I looked these examples but it used HAL Library and I don't want to use HAL , but thank you your response
Re: Hello, how can I write start,stop,address and write functions for I2C Master Mode in stm32g031k8
2021-04-08
Thank you, I will look.
Re: Hello,I use microphone and When I talk I get the data from microphone to eeprom.I want to playback to speaker from eeprom .I think,I have to produce analog signal.But I shouldn't use DAC .How can I produce Analog signal without DAC in stm32 ?
2021-01-10
In the PWM ,I can change duty cycle and frequency but I think ,I have to change amplitude
Re: Hello,I use microphone and When I talk I get the data from microphone to eeprom.I want to playback to speaker from eeprom .I think,I have to produce analog signal.But I shouldn't use DAC .How can I produce Analog signal without DAC in stm32 ?
2021-01-10
How can I change PWM'S amplitude?
View more
Kudos from
User
Count
Legacy member
1
View all