About Sebastian K.

Sebastian K. · 2018-01-08

Posted on January 08, 2018 at 13:26Hello,another question regarding the Nucleo-L432KC board. The user manual states that it can be powered via the +5V pin or the VIN pin. However, when I want to power it via +5V, I can't get the board to run. The re...

Sebastian K. · 2018-01-04

Posted on January 04, 2018 at 21:48Hello,I am having a problem with a simple data logging project on an L432KC Nucleo board.I have a microSD breakout board from Adafruit hooked up via SPI1 and receive data on USART1 via DMA using a circular buffer f...

Sebastian K. · 2018-01-02

Posted on January 02, 2018 at 16:32Hello,I just bought a NUCLEO-L432KC board. I understand that of its 2 USARTs the USART2 is connected to the ST-Link Virtual Com Port via pins PA2 and PA15.The RX pin PA15 apparently is not broken out on the Nucleo ...

Sebastian K. · 2017-08-09

Posted on August 09, 2017 at 17:42Hello everyone,I am having some trouble understanding the behaviour of the HAL_UART_Transmit_IT and HAL_UART_Receive_IT routines. I am using two NUCLEO-F767ZI boards that communicate via UART1 in a request/reply fas...

Sebastian K. · 2017-05-26

Posted on May 26, 2017 at 16:25 Hello, I am having problems communicating with my NUCLEO-F767ZI board over the virtual COM port on Linux. The board uses USART3 to communicate via the ST-Link USB port with the PC. The ST-Link connects fine to th...

Sebastian K. · 2018-02-06

Posted on February 06, 2018 at 21:29To generate the code for the peripherals I can only recommend to start with CubeMX, add the peripherals you need and generate a project for the toolchain of your choice. Some very basic code examples can also be f...

Sebastian K. · 2018-02-06

Posted on February 06, 2018 at 21:54I am pretty sure you want to setup one single ADC handle withhadc3.Init.NbrOfConversion = 2;and then assign Rank=1 and Rank=2 to each channel, because the way you do it it seems that there are two identical handle...

Sebastian K. · 2018-02-05

Posted on February 05, 2018 at 22:05Hello,I also played around with the STM32 MAT Target in Simulink, and in my humble opinion it is hopelessly buggy and non-functional. I could not get even simple examples to work (that was about a year ago already...

Sebastian K. · 2018-01-08

Posted on January 08, 2018 at 21:01Ok, thanks for the link. What I understand is that apparently SB9 needs to be removed for this to work, which includes a risk that I cannot reprogram the MCU anymore. So I will scratch that option and try to work w...

Sebastian K. · 2018-01-06

Posted on January 06, 2018 at 17:41romain reicher wrote:Hi Sebastian K.This is a software expansion. There is nothing to install with the Cube.You just have to extract the archie zip and copy it to your computer.You can either use the examples that ...

User statistics

User Activity

Nucleo-L432KC power options

Writing to SD card via SPI interfering with USART DMA Rx?

USART VCP connections on NUCLEO-L432KC

Question about behaviour of HAL_UART_Transmit_IT

Nucleo F767 - Serial com. over virtual com port on Linux

Re: STM32-MAT-TARGET Can not find which APB timer TIM1 is connected to.

Re: How to get data from ADC with STM32F7

Re: STM32-MAT-TARGET Can not find which APB timer TIM1 is connected to.

Re: Nucleo-L432KC power options

Re: Nucleo-L432KC store data in Flash using mbed