Solved

I am working on a project that uses the ST67W611 for cloud connectivity, but I am experiencing some issues when trying to connect to AWS IoT Core.Note: The NCP is already flashed with the T01 binary. The AWS endpoint is correct — for the sake of this question, let’s assume it is:xxxxxx-something.amazonaws.com. What Works Broker: test.mosquitto.org I am able to publish data to the broker and receive data from it when using test.mosquitto.org. However, I am now trying to get it working so that our custom device can connect to AWS IoT Core. MQTT Configuration (This is my current MQTT configuration.)   #define MQTT_BROKER "xxxxxxxxxxxxxxxxxxus-west-1.amazonaws.com" #define MQTT_PORT 8883 #define MQTT_CLIENT_ID "Thing01" #define MQTT_USE_TLS 4 #define MQTT_KEEPALIVE_S 60 static const char s_aws_ca_cert[] = "-----BEGIN CERTIFICATE-----\r\n" "Conten........\r\n" "Conten........\r\n" ..... "-----END CERTIFICATE-----\r\n" static const char s_aws_client_cert[] = "-----BEGIN CERTI

Hello everyone, I am currently working with the NUCLEO-L452RE-P board and trying to evaluate its low-power performance. I am measuring the current consumption using jumper JP6 (IDD measurement point). The jumper is removed and a multimeter is connected in series. My setup: Board powered via ST-LINK USB (then power-cycled before measurement) No external peripherals connected All GPIOs configured as analog, no pull-up/pull-down Debug set to "Serial Wire" (no trace) No RTC or wake-up sources enabled My code is as follows (I intentionally included the complete code to avoid missing any relevant detail): /* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * Copyright (c) 2026 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be

Hi I am using latest CubeMx Ver 16.7.0 and CubeIde Ver 2.1.1while trying to compile a USB CDC code this error shows once i linked the code :"C:/Users/../../Hardware - General/../Electronics/../Software/USB_CDC_U0/USB_CDC_U0/Debug/../Core/Src/stm32u0xx_hal_msp.c:102:(.text.HAL_PCD_MspInit+0x4c): undefined reference to `MX_USB_CDC_Init'C:/ST/STM32CubeIDE_2.0.0/STM32CubeIDE/plugins/com.st.stm32cube.ide.mcu.externaltools.gnu-tools-for-stm32.14.3.rel1.win32_1.0.100.202602081740/tools/bin/../lib/gcc/arm-none-eabi/14.3.1/../../../../arm-none-eabi/bin/ld.exe: (MX_USB_CDC_Init): Unknown destination type (ARM/Thumb) in ./Core/Src/stm32u0xx_hal_msp.oC:/Users/../../Hardware - General/../Electronics/../Software/USB_CDC_U0/USB_CDC_U0/Debug/../Core/Src/stm32u0xx_hal_msp.c:102:(.text.HAL_PCD_MspInit+0x4c): dangerous relocation: unsupported relocationcollect2.exe: error: ld returned 1 exit statusmake: *** [makefile:65: USB_CDC_U0.elf] Error 1 "the called the function "MX_USB_CDC_Init" exist i

Hello,I am trying to share ST-LINKV3 over the network and use it from another PC (WSL Ubuntu distro running docker and connecting to ST-LINKV3 via OpenOCD) with VirtualHere program (client and server), but facing this issue:Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'. Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD Info : clock speed 1800 kHz Info : STLINK V3J17M10B6S1 (API v3) VID:PID 0483:3753 Info : Target voltage: 3.141644 Info : [stm32h7x.cpu0] Cortex-M7 r1p1 processor detected Info : [stm32h7x.cpu0] target has 8 breakpoints, 4 watchpoints Info : starting gdb server for stm32h7x.cpu0 on 3333 Info : Listening on port 3333 for gdb connections [stm32h7x.cpu0] halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x0800bcb4 msp: 0x2001fff0 Info : Device: STM32H74x/75x Info : flash size probed value 2048k Info : STM32H7 flas

We are pleased to announce that STM32CubeProgrammer 2.22 is available What is new in 2.22: Support for the STM32U3 microcontrollers with 2 Mbytes of flash memory: Internal memory programming through debug and bootloader interfaces Option bytes programming through debug and bootloader interfaces OTP programming through debug and bootloader interfaces Core register programming through debug interfaces Automatic mode Serial Wire Viewer Register viewer Firmware encryption/signing RDP regression with password SFI through debug and bootloader interfaces (USB and UART) Support for STM32C5 series microcontrollers: Internal memory programming through debug and bootloader interfaces Option bytes programming through debug and bootloader interfaces OTP programming through debug and bootloader interfaces Core register programming through debug interfaces Automatic mode Register viewer Firmware encryption/signing RDP regression with password Support for STM32WBA2xxx microcontrollers: Inter

I work in a workspace but I use vim with clangd for editing my code. I am wondering if it is possible to create a compile_commands.json file and if so how. If the IDE uses cmake under the hood then it should be rather straightforward but I cannot understand how to proceed. see e.g. this:https://cmake.org/cmake/help/latest/variable/CMAKE_EXPORT_COMPILE_COMMANDS.html 

Hello! Has anyone tried to deploy multiple neural networks on a stm32n6 at once? I'm developing an application which requires 5 NN. I created 5 .c libraries to deploy each NN on the NPU, I assume is because of the APIs that they overlap. So I'm curious if anyone has tried this and how it was solved. My last  option is to create a bigger models that contains all 5 on onnx, then deploy it, idk if someone knows if this could work to. 

Hello, I didn't find the layout this board online. can someone help me find the layout of this STEVAL-L99MH98 board? Layout I am asking is not present in the user manual of this board.   Thank you, Br, Gopal

Hello, Does anyone know where I can find the safety manual for L99mh98 octal half bridge driver?   br, Gopal [moderation edit: removed label Gate Drivers, added Automotive Power]

Hello.I'm having trouble transfer the UserApp to SBSFU. Here's the description of the issue.I am working on SBSFU on STM32H753-Eval, So i altered the given sample for my UART to map to ST-LINK VCP. I am able to see logs post this changes. Later I Dissabled all security stuffs with below macro and fully erase the board (by setting RDP level 1->0 ).I'm using the 2-Image example code, All security feature were disabled by#define SECBOOT_DISABLE_SECURITY_IPS in app_sfu.h. I loaded SBSFU.elf onto the board and transferred the UserApp.sfb via YMODEM. However the program went into a infinite reset loop. It is rebooting every time i send UserApp.sfb.  I tried Increasing the Download Timeout from 3000 to 10000 from this macro, same issue  /* Teraterm YMODEM */ /* #define SFU_COM_YMODEM_DOWNLOAD_TIMEOUT ((uint32_t)3000U) */ #define SFU_COM_YMODEM_DOWNLOAD_TIMEOUT ((uint32_t)10000U) /* IIs there any specific step i need to follow ?... kindly guide me here.&nb

Hi,while integrating the module, we noticed that UDP client connections appear to be explicitly blocked in the driver (w61_at_net.c) for mission_t01 firmware (LwIP offload). The following code only allows TCP and SSL connections:if ((conn->Protocol != W61_NET_TCP_CONNECTION) && (conn->Protocol != W61_NET_TCP_SSL_CONNECTION) #if (W61_NET_IPV6_ENABLE == 1) && (conn->Protocol != W61_NET_TCPV6_CONNECTION) && (conn->Protocol != W61_NET_TCPV6_SSL_CONNECTION) #endif /* W61_NET_IPV6_ENABLE */ ) { NET_LOG_ERROR("Only TCP and SSL protocols are supported for client connections\n"); return W61_STATUS_ERROR; }However, according to the official AT command documentation, UDP client connections are supported:https://applist67.github.io/Web_AT_Documentation_ST67/v2.0.106/index.html#establish-udp-connectionAfter commenting out this restriction, I was able to establish a UDP client connection successfully, and communication seems to work.Is there a specific reason why

Hi,I am presently planning to use Viper265K part for High Voltage Buck converter design with below requirements: MinMax  Vin200900V Vout4.5 V+/-5%Iout0.44 A Pout2 W  With above requirements the duty cycle for the device is observed to be 0.5%. Please can you help me to know if the device can be used for such low duty cycle and what would be recommendation from your side for achieving above design requirement.

Hi,I'm trying to control a BLDC motor connected to B-G431-ESC1 driver in Open Loop Voltage mode. With Motor Pilot control there's no problems. I'm not able to find the correct HAL commands to use for:A) Set Open Loop Voltage mode ( B) Set the reference voltageC) Set the speed in RPMStart, Stop, Ack Fault commands are ok. AI gave me a lot of indications but nothing seems work ok. Many thanks who will help me.Bye  Rossano 

Hi I have a question regarding use of STL6P3LLH6 MOSFET in the reference design as shown in EVAL-SCS001V1. In this reference, there is only one STL6P3LLH6(T1) used as shown below:   But in the datasheet of STUSB4500, Fig 10 shows use of 2 such MOSFETs as shown below. What is the advantage of using 2 of these? In my design, i will use STUSB4500 to negotiate only fixed 20V, 2.5A. So, wondering if i need to put 2 MOSFETs or would it be OK with only one?Thanks!   

Hi Community,I am working on STM32H747I-DISCO Board and trying to bringup digital MEMS Mic (MP34DT05) which is integrated on STM32H7-DISCO Board.I am trying to record random voice for 5 seconds and need to play back via audio jack out which is connected to codec also it is integrated on the board. I am sharing you schematic of the board as below:MP34DT05 is connected to MCU directly with SAI4 Interface and Solder Brifdges are provided to connect via codec Here I developed the application code to interface and record via MIC and playback via Audio Jack out./* Includes ------------------------------------------------------------------*/ #include "main.h" /* Private includes ----------------------------------------------------------*/ /* USER CODE BEGIN Includes */ #include "stm32h747i_discovery_audio.h" #include <math.h> #include"log.h" #include<string.h> #include "pdm_config.h" #include "pdm2pcm_glo.h" #include <stdio.h> /* USER CODE END Includes */ /* Private t

Hi Team,Is there any framework or lib support available from ST for automation testing of TouchGFX based UI either on simulator or on actual device?If anyone has any idea or workaround, then please share!Thanks

Left commented out SFU_NO_SWAP and defined ENABLE_IMAGE_STATE_HANDLING in app_sfu.h, but when trying to build SECoreBin and SBSFU errors appear:/Middlewares/ST/STM32_Secure_Engine/Core/se_fwimg.h:47:61: error: unknown type name 'SE_FwStateTypeDef'Is there something I am missing? I selected AES-GCM crypto schemeI have followed https://www.st.com/resource/en/application_note/an5056-integration-guide-for-the-xcubesbsfu-stm32cube-expansion-package-stmicroelectronics.pdf (Chapter 8.5)  

Hi all! I'm trying to implement a wear leveling in user memory accessed from I2C for a counter on bit level. My question is: Are ST25DV eeprom byte cells similar to classic ones where each write cycle starts with a clear (which sets the byte to 0xFF) and after it writes 0 bits where needed? Or is there somewhere an inversion taking place? Could someone help me, by pointing out some directions in datasheets for me in this matter? I found another post where memory default state is quoted from the datasheet which specifies that factory default is 0x00, but this doesn't imply that it's default state isn't 0xFF. Thanks in advance, notram

I have been using RFAL succesfully with STM32L4. For a more price sensitive project I need to port the code to STMG070 and I cannot get RFID readings to work. Measuring ampltiude gives same result on both codes:st25r3911MeasureAmplitude(&c); printf("Amplitude %d\n\r", c); The following have been verified:* Same RFID PCB is used for both processors (RFID PCB and processor PCB are connected by pin connector)* Same RFID card is used* Init of RFAL gives ID 13 on both codes* GPIO interrups are generated* Same LDO on both PCB* Voltage to ST25R3911B is stable* Both processors runs at same frequency 16 MHz On STM32L4 the state change (during a succesful RFID read) of rfalNfcWorker goes like:RFAL_NFC_STATE_IDLERFAL_NFC_STATE_POLL_TECHDETECT x 19RFAL_NFC_STATE_POLL_COLAVOIDANCE x 29RFAL_NFC_STATE_POLL_ACTIVATION x 2But when running on STM32G070 RFAL_NFC_STATE_IDLERFAL_NFC_STATE_POLL_TECHDETECTRFAL_NFC_STATE_LISTEN_TECHDETECT until timeout  Anyone have

The STM32L476 does not have an nBOOT0 option bit in its option bytes. Is there a way to boot from the main flash memory without using the BOOT0 pin?

I'm developing using the STM32WBA65I-DK1. I'd like to know how to implement interrupt handling for button presses. It appears that stm32wba65i_discovery.h does not contain any APIs related to button presses (which is perhaps to be expected since the DK does not have push buttons). The sample code I'm using is BLE_HeartRate_Thread. If you have any source code that might be helpful, please let me know.

Hi everyone,I'm facing a really frustrating issue where my STM32CubeIDE can no longer detect my ST-LINK, and I've narrowed the problem down specifically to stlinkserver.exe failing to launch. This problem appeared completely randomly on my PC.Here are the symptoms and what I have already ruled out:The Problem: When I try to manually execute stlinkserver.exe via PowerShell to see what's wrong, it exits instantly without printing any output, errors, or logs. Even forcing the help menu or debug mode does absolutely nothing:PowerShell PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe -d 5 PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe -h Running Get-Process stlinkserver confirms the process is not running in the background at all. It just dies immediately upon execution.What DOES work (Hardware & Drivers are fine):STM32CubeProgrammer

Hello everyone   i am currently working on a project with a NUCLEO-C092RC Board. With this Board i want to send OBD-II Frames to my car and receive reponses with data. I also use a LCD Display via SPI. But now i have a problem. i connected CANH/L with the Board. I also connected 12V and GND from the OBD-II-Port to a buck converter, which steps the voltage down to 7 V for VIN on the Board, which should be within spec. Then i tried to send a frame, but i did not get a response, when the Board was only powered by 12V via buck converter. After that i think i broke my MCU, because then i connected my PC with the Board and switched the power source back from VIN to ST-Link with a jumper. I was able to debug my programm. but when i also disconnected CANL and CANH from the Board or switching the jumper from VIN to ST-Link (i am nor sure anymore), the red LED from STMPS2141STR came on. It only turns off, if i disconnect VDD from 3V3 Volt with pulling JP5. I also measured from what i think

Hello,   I would like to learn if there is an easy way in STM32CubeMX2 to start a new project with an existing ioc2 file. It seems that the only way I can do this is make a copy of the ioc2 file, do a text find and replace for the name of the project and reopen the project in MX2. In essence, I like to start a project from a working ioc2 configuration and modify it to work on a fork of the project. I don't want to recreate a complex configuration from scratch because I found the hard way that it is easy to make mistakes or to omit something.   Thank you, -Gil   Please check the follow-up discussion here: Issue with Save As feature in STM32CubeMX2

I'm designing a USB-C charging circuit for a battery-powered device using the STUSB4531 for PD negotiation alongside a BQ25792 buck-boost battery charger. The BQ25792 handles the full VBUS power path internally (inrush limiting, reverse current protection, OVP, and dead battery support), so I'm trying to understand whether the external P-FET that STUSB4531 normally drives is still required. Specifically: 1. Can the GATE pin be left NC or tied off without affecting CC detection and PD negotiation? Or does the IC require a valid FET load on GATE to operate correctly?2. If the GATE pin must drive something, would it be acceptable to connect GATE to the BQ25792's CE (charge enable) pin instead of a FET gate — effectively using it as a charger enable signal rather than a loadswitch?3. Dead battery / no battery scenario: I need the system to power up from VBUS even when the battery is absent or fully depleted. The BQ25792 already supports dead battery mode on its own. If the external FE