Solved

Dear ST,Now I'm testing my VL53L7CX sensor that is on the package P-NUCLEO-53L7A1 in Autonomous Mode with integration time = 2ms, ranging freq. = 4Hz and 4X4 Resolution, the attached screen-shot represents the output current related to my integration time and it's typically 2ms.My question is about the added peaks after the integration time peak, Why could this happen?and, How can I eliminate or reduce it?Knowing that the duration of these peaks illustrated in the other screen-shot attached.Thank you.    

With the recent split of STM32CubeIDE and STM32CubeMX, I'd like to propose a dark mode option be added to STM32CubeMX.In consideration of the competing priorities for STM's software development team, I have two suggestions for how this proposal could be implemented:The first suggestion is the typical route: STM's in-house software development team add the UI theming and inputs to switch between dark and light mode.The second suggestion is less typical: make STM32CubeMX open source and let the larger software community assist with adding dark mode. Perhaps the source could be placed alongside other repositories in STM's current GitHub account....The benefits of adding such an option would be as follows:Consistency with STM32CubeIDE, from which STM32CubeMX was split from (STM32CubeIDE already has a dark mode)Consistency with the vast majority of other software in the industryConsistency with what has become a common user experience across operating systems, browsers, and setups in g

Hi, We are planning to use STM32H743ZI for our project. Our requirement is to interface a 7-inch LCD touch display with 1024x600 resolution using a 24-bit RGB interface (RGB888) through LTDC. Can STM32H743ZI reliably support this display resolution? Also, what frame rate can realistically be achieved with this configuration? Are there any important hardware or performance considerations before selecting this MCU? Any suggestions or reference designs would be helpful. Thanks.

Hello There,I am currently trying to use the ST25R200 with the X-CUBE-NFC10 Software package.First thing am not sure about: In the "Software Packs Component Selector" I have to configure the "Board Extension NFC/NFC10A1" even when i don't plan to use this board. Otherwise i get a warning that "NFC10Boardlface" requires "NFC/NFC10A1". If I don't select the board part, I get a simmilar warning from the RFAL component.If i either don't add NFC/NFC10A1 in the component selector or don't select "Board Part NFC10Boardlface" in the Mode selection for the X-CUBE-NFC10 package, CubeMX seems to have problems generating the header "nfc_conf.h", which i have attached to this post.This is how the configuration looks, which generated nfc_conf.h:Am I using this library not correctly? Or rather which components of this library am i supposed to configure if i want to use the library with a custom board based on the ST25R200?Best Regards, Cecil

I have created a firmware for a STM32L010F4Px microcontroller.I was able to Connect and Download Firmware by using ST-LINK V2.For some reason, I can't connect to the MCU at the moment by using CubeProgrammer + ST-LINK V2.Instead, I can connect/debug my microcontroller by using a SEGGER J-Link Ultra+ + J-Flash tool.The log from CubeProgrammer doesn't give me much details:13:28:34 : UR connection mode is defined with the HWrst reset mode13:28:34 : ST-LINK SN : 37FF71064E573436D2C1144313:28:34 : ST-LINK FW : V2J47S713:28:34 : Board : --13:28:34 : Voltage : 3.28V13:28:34 : Error: Unable to get core ID13:28:34 : Error: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug Authentication

I'm working on STM32mp25f-EV1, i have downloaded FLASH-stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v26.02.18 package but i'm facing problem while accessing SSH.

Hello, I'm trying to configure my SAI to receive TDM packets from my external ADC. For some reason, no matter what sample rate I choose, the real audio and error between selected is always 0. I've tried changing the clocks to the SAI1 module to 50 and 100 MHz, but it didn't change anything. Is this a visual bug with CubeMX or is it something with how I'm configuring the peripheral? Thanks.  

Excuse me, how can I implement this kind of loadingI'm really at a loss for ideas. Please help me out, thank you

Hi all, I'm planning to use USB (DFU mode) for production programming of the STM32C071K8U6 — including the very first firmware upload. The board has no external crystal; I intend to rely solely on the internal RC oscillator.   A few questions: 1) Is USB DFU feasible on this specific part without an external crystal? I've read that not all STM32 variants support USB boot without an external crystal (due to clock accuracy requirements for USB). Can anyone confirm whether the STM32C071K8U6's internal oscillator is sufficiently accurate for this?   2) Are there any specific hardware or configuration requirements I should be aware of for first-time USB DFU programming on this part? As the moment I just have the two USB traces connected to the USB connector but no 5V (VBUS) connected anywhere to the micro. I also have a pushbutton on the BOOT0 pin.   3) What USB speed does the built-in bootloader use, and is it possible to force a lower speed? The reason I ask is that the USB

Hi, we have purchased stm32h750vbt6 microcontroller for analog signal validation with 10k potentiometers to integrate with game controller joystick especially joy.cpl using windows 10 OS.   We have dealt with DMA Circular mode configuration pointing cortex-M7 DRAM to 0x30000000 to retrieve the analog signals associated with respective 10k potentiometers. Totally we have four analog pins such as PA0,PC0,PA3 and PC5 from ADC1 & ADC2 with proper distinguished rank allocation alongside desired maximum sampling cycles but although we have altered and tested with different values of this above configuration it ended up with ADC channel leakage which is declared 16 bit ADC.    Moreover we have tried adding external 100nf capacitors to avoid these linkage but failed.    We kindly request you to resolve the ADC channel leakage in our current stm32 Project. Our entire stm32 project attached for your reference and fault identification.  

I am using the Analog Devices EVAL-ADE9430 Evaluation board for testing one of their devices. The Evaluation board uses the NUCLEO-144 STM32F413ZH processor. I am using the Keil uVision development setup to run and debug code.  I am specifically concentrating on the SPI Bus Driver and the timing. I have no previous experience with STM Devices and how the SPI transfers happen in the processor. so I apologize a head of time.  My question is very basic I am trying to understand how the NUCLEO-144 STM32F413ZH board is transmitting the data over the SPI Bus. What setup is involved and what kicks off the actual transmission in the the HAL_SPI_Transmit() code below. The code i am using is transmitting 8 bits at a time.  The Chip Enable (SS) is set active prior to this code. I see a structure called hspi that has a bunch of parameters that are initialized at line 29 below By single stepping know when line 108 below executes I can see 8 bits of data on my scope. I

DeviceSTM32H563ZIT6, single binary (no separate bootloader), dual-bank OTASetup Bank1: Current running firmware (original)Bank2: New OTA firmware (potentially corrupted)IWDG: Started in Bank1 before swapOTABootSafetyCheck: In Reset_Handler of every binary buildBKP0R: Boot counter set before swapProblemAfter bank swap, if Bank2 firmware is corrupted and Reset_Handler never executes:  Bank swap → resetCPU reads 0x08000000 → SP (may be valid)CPU reads 0x08000004 → Reset vector (may be valid)CPU jumps to Reset_Handler addressReset_Handler code is corrupted → garbage instructions → crashOTABootSafetyCheck never runsBoot counter never incrementsIWDG fires → reset → same crash → infinite loopRollback never happensBank1 original firmware never recoversDevice is permanently stuck What We Have Tried1. OTABootSafetyCheck in Reset_Handler  asmReset_Handler: ldr r0, =_estack mov sp, r0 bl OTABootSafetyCheck ; before SystemInit and main bl SystemInit bl __libc_init_array bl

Hello,I am an engineering student working on my senior graduation project using the STEVAL-WBC2TX50 evaluation board. I need the STSW-WBC2STUDIO (or the updated WPSTUDIO) GUI to configure the board, but all official links on the ST website return a 404 error.Could you please provide a working download link or the installer files? My project exhibition is approaching soon, and this is a critical blocker.Thank you for your support.

ST moderator: updated the title to be more concise according to the below exchanges. Hello All,   I am facing a problem for debugging one of the board which uses stm32h7 controller. I am not sure why this is happening but on other board I am able to debug it, but for first one its not working. Though the code and debug config settings are same for both the board and using same system to debug both, but on one board I am able to debug while on other its is not. so could you please tell me what I can try to resolve this issue.   Thanks, SD 

Hi, I have all configured using internal loop FDCAN1 and there is not working on my STM32G474RE-Nucleo board 

Hi, We are busy making a setup with 2 nucleo-c092rc boards. Our first test was to send from board 1 to board 2 by the integrated CAN interface on these boards. We started at 1Mbits and this worked great. Also on 4Mbits the setup worked great. But we also want to test this on 8Mbits and now the transmitter is not sending correctly. We only see that the arbitration phase is send out and a couple of bits of the data part, but then the transmitters stops sending. We have tried with internal HSI(48Mhz) and external HSE crystal which is also 48Mhz on the nucleo boards.  We calculated the values for the SyncJumpWidth and timeseg1 and 2 and also tested with values slightly altered. hfdcan1.Init.DataPrescaler = 1; hfdcan1.Init.DataSyncJumpWidth = 2; hfdcan1.Init.DataTimeSeg1 = 2; hfdcan1.Init.DataTimeSeg2 = 3; But we allways have the same outcome. Sometimes it's not sending anything and sometimes only a small part of the total message of 64 bytes. What could be the issue here?  

This is some feedback for the STM32C5 OEMiRoT example provided by ST.This is based on the STM32C5-MCU-HAL2.0.0 pack download 06-05-2026.Attached you can also find the CMake Config files for the example, specifically for the NUCLEO-C542RC board.General Bug Provisioning Python ScriptThe provisioning python script has a small bug when it comes to the prebuild script which adjusts the linker files.These files are compiler specific so the correct adjustment function needs to be called.This compiler dependent code is missing in the `_update_linker_define()` function in `STM32C5-MCU-HAL/rot/rot_provisioning/helper/project/project_generic.py` starting at line 318:linker_path = self.config.get_compiler_linker(compiler) value = f"0x{self.flash_layout.get_flash_layout(define):X}" update_define_in_file(linker_path, define, value)change tolinker_path = self.config.get_compiler_linker(compiler) value = f"0x{self.flash_layout.get_flash_layout(define):X}" if (compiler == "gcc"): update_variable_

Hello, ST expert For GPIO structure, what are the differences between FT and TT mode? Are there any differences for the ESD diode and the other diode in these two modes?     BR Yang  

Hi All,I've just been watching an ST tutorial video on how to implement  bare-metal Device CDC USB  on an STM32U3.During the video, the lecturer says that the code is available within the workshop download. No link is provided to the workshop code....Does anyone know where I can find it? This is the video in question : https://youtu.be/m8ph9JIY5QE?list=PLTJzs51NlEIAHFfePhKJPsnWvT5XidJuU&t=1164Any help would be appreciated.CheersMichael 

Hello ,I am working on a project with the STM32L562CET6 microcontroller and have encountered an issue with the timer interrupt callback function.   1. I configured TIM6 as the clock source for the microcontroller. Consequently, the HAL_TIM_PeriodElapsedCallback() function is automatically triggered whenever the TIM6 interrupt occurs.   2. Now, I have configured TIM2 for a different purpose, but I noticed that when the TIM2 interrupt occurs, the same HAL_TIM_PeriodElapsedCallback() is triggered.Since the HAL_TIM_PeriodElapsedCallback() is defined with the weak attribute, I understand that I can redefine it in my user code. However, this causes conflicts when multiple timers (like TIM6 and TIM2) trigger this callback.Questions:  1. Is there a way to alias or redirect the HAL_TIM_PeriodElapsedCallback() to separate functions for different timers (e.g., one for TIM6 and another for TIM2)?  2. Is there any other specific callback function available for timers i

Hi All,    I want to do something very basic, but somehow cannot manage to do it. What happens if you have a PWM signal on an IO Pin, generated by a timer, and you disable the timer?  What happens to the physical IO Pin ? Is it stuck at the state where it was when you disabled it ?, Does it go Low ? Or High. The Idle state of the Timer is Low, and the On state High.    Thanks,  DJ 

I am trying to learn how to program a STM32 micro-controller, specifically a STM32C593. The thing is according to its datasheet it has Ethernet functionality, bit it is missing in the peripheral list inside STM32CUBEMX2 IDE. 

Hello ST Community team,I would like to report a possible inconsistency in the STM32 MCU Portfolio Selector regarding Ethernet filtering for the STM32C5 series.While selecting MCUs using the Portfolio Selector, I filtered devices through:- EthernetThe reference STM32C593CET6 appears as supporting Ethernet functionality. However, according to DS15136 (Table 1), this specific MCU does not include the Ethernet peripheral.This may create confusion for developers, especially since the STM32C5 family is still relatively new and many users rely on the Portfolio Selector during early device selection.Could you please review and correct this behavior.Ps: more details available on this post. Best Regards.II

Hello!I am having trouble verifying NPU operation on the NUCLEO-N657X0-Q board.I am trying to test a simple INT8 FNN (Feed-Forward Neural Network) using an ONNX model. The project was generated via X-CUBE-AI within CubeMX. I have configured the AXI and Clock settings (CPU: 600MHz, NPU: 800MHz, NPU AXI: 800MHz) and, given the model's simplicity, I set it to use internal SRAM only.While the code execution seems to flow correctly without errors, I noticed that the output values are not being updated. The output buffer remains unchanged, or in some cases, still holds values that look like the input data. It seems the NPU's computation results are not being written back to the memory correctly.I would greatly appreciate any advice or suggestions, even if they aren't complete solutions!Environment Versions:CubeIDE: 2.1.1CubeMX: 6.16.1CubeProgrammer: 2.22.0ST Edge AI: 4.0ST-LINK: V3J17M10I have attached one of the project files I’ve been testing for your reference. Thank you always for your s

Dear STMicroelectronics Community / Support Team,I hope you are doing well.I am currently working with the STM32N6 Discovery Kit and noticed that it uses an external Octal NOR flash device with the part number MX66UW1G45G. However, I have been unable to locate a public datasheet for this exact component.I was able to find datasheets for similar parts such as MX66U1G45G and MX66UM1G45G, but not for the “UW” variant used on the board. This has led to some confusion regarding the exact specifications, supported features, and command set of the device.I would appreciate your guidance on the following points:Is MX66UW1G45G a custom or internal part number used specifically for STM32 evaluation boards?Is there a publicly available datasheet for this device, or can it be shared upon request?Can MX66UM1G45G (or another publicly documented part) be considered a fully compatible equivalent for development purposes?Are there any specific differences (e.g., command set, timing, interface behavior)