Solved

Posted on April 05, 2017 at 00:02Although powering an LSM9DS1 with 2.8V to VDDIO and VDD, I would like to use a 1.8V-logic line for one of the chip selects for ease of retrofitting an existing design with minimum upheaval.  The line is push-pull, not open collector.The sufficient-voltage threshold for a '1' digital input is usually labeled V_IH, but I could not find that parameter listed in the published specifications.  What is V_IH for the LSM9DS1 digital inputs, especially the chip selects?A corollary question -- even if 1.8V will be sufficient fully to deselect the chip-select, would using 1.8 instead of 2.8V lead to increased power consumption?Thanks!#lsm9ds1

Posted on April 05, 2017 at 12:42Looking at the STM32F767xx Datasheet (DocID029041 Rev 4), the SRAM1 address is listed as 0x20020000.But the STM32F76xxx Reference Manual (DocID028270 Rev 2) lists this as 0x20010000 in several places: Page 98/1896: 'BOOT_ADD0 = 0x8004: Boot from SRAM1 (0x2001 0000)'Page 99/1896: 'BOOT_ADD1 = 0x8004: Boot from SRAM1 (0x2001 0000)'Page 112/1896: 'BOOT_ADD1 = 0x8004: Boot from SRAM1 (0x2001 0000)'Page 112/1896: 'BOOT_ADD0 = 0x8004: Boot from SRAM1 (0x2001 0000)'Is this a typographical error?#stm32f767 #stm32f767zi-nucleo #stm32f767zi-nucleo-board #stm32f7

Posted on April 02, 2017 at 18:19Hi all,I am developing an application with my STM32F746G-Discovery board; for this application I need to acquire 4 to 6 analog signals from external sensors.My application uses the Arduino UNO headers on the back of the discovery board to interface with a motor driver shield by Pololu; I was already able to generate the logic and PWM signals to control the motor status, direction and rotation speed by means of an LCD GUI.Now I need to acquire some analog signals from external sensors, possibly using DMA to transfer ADC samples in memory.Until now I was able to initialize the ADC and DMA using STM32CubeMX, defining the needed ADC3 channels, associated ranks, working mode and so on.This is the MX_ADC3_Init function generated by STM32CubeMX:/* ADC3 init function */static void MX_ADC3_Init(void){   ADC_ChannelConfTypeDef sConfig;    /**Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of convers

Posted on April 04, 2017 at 14:50Hi,I tried to connect to the STM32F413 with OpenOCD, but I get the following error:Info : device id = 0x10006463Warn : Cannot identify target as a STM32 family.Error: auto_probe failedI searched the source code of OpenOCD 0.10.0 and it seems as if the F413 is not yet supported. Does anyone has a patched version of OpenOCD with support for the STM32F413?Best regards,Stefan#openocd #stm32f413

Posted on April 03, 2017 at 15:57Hi,I am using the STM32F071C8 on one of my projects and it is of at-most importance that I get the IAP working. Jumping from my bootloader code to my main app code is not a problem. I copy the vector table to memory and remap to use the SRAM with the __HAL_SYSCFG_REMAPMEMORY_SRAM function. Obviously tweaking my linker files.I do not want to call HAL_NVIC_SystemReset from my main app because I want to preserve the state of my IO pins, while programming the new bin file, so I was thinking of jumping back to my bootloader. While it seems that I can jump back it does not seem to be stable. Sometimes I get systick issues or sometimes it is just running 'weird'. I tried to to the copy to memory and remap the vector table again and even tried to call __HAL_SYSCFG_REMAPMEMORY_FLASH without the copy but to no avail.Any ideas what I can try to get this 'jumping' up and down up and running?Jeff

Posted on March 23, 2017 at 19:38The problem is a complier error because in the cube MX (version 4.20.0)for the STM32F373R8Txusing ADC1 (12 bits ADC) I can choose, in the configuration tab,ADC1 and as external trigger source for regular conversion the TIM4 CC4 event....this will generate this code:.... hadc1.Instance = ADC1; hadc1.Init.ScanConvMode = ADC_SCAN_ENABLE; hadc1.Init.ContinuousConvMode = DISABLE; hadc1.Init.DiscontinuousConvMode = ENABLE; hadc1.Init.NbrOfDiscConversion = 8; hadc1.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T4_CC4; <-- compiling this will generate an undefined error ! hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT; hadc1.Init.NbrOfConversion = 8;....in the HAL libary header (version 1.7.0 lates up to date) stm32f3xx_hal_adc_ex.hat the line 1349 there is: &sharpdefine ADC_EXTERNALTRIGCONV_T4_CC2 ADC_EXTERNALTRIG_T4_CC2at the line 1827 there is: &sharpdefine ADC_EXTERNALTRIG_T4_CC2 ((uint32_t)(ADC_CR2_EXTSEL_2 | ADC_CR2_EXTSEL_0))Reading at the ma

Posted on April 03, 2017 at 05:07I've been playing with the hal sd card driver today.printf(' Product name : %lx%x\r\n', pSD_CID_Info.ProdName1, pSD_CID_Info.ProdName2);where pSD_CID_Info is of the type HAL_SD_CardCIDTypeDef which istypedef struct{  __IO uint8_t  ManufacturerID;  /*!< Manufacturer ID       */  __IO uint16_t OEM_AppliID;     /*!< OEM/Application ID    */  __IO uint32_t ProdName1;       /*!< Product Name part1    */  __IO uint8_t  ProdName2;       /*!< Product Name part2    */  __IO uint8_t  ProdRev;         /*!< Product Revision      */  __IO uint32_t ProdSN;          /*!< Product Serial Number */  __IO uint8_t  Reserved1; &nbs

Posted on April 02, 2017 at 02:40I have a part in a car infotainment system that I can't identify. It has ST branding, but I can't figure out what it is. Can anyone help me? I've uploaded 2 shots of the same part. Thank you.

Posted on November 04, 2016 at 13:42 In STM32Cube MX 4.17 I have set up an empty STM32L476 Nucleo project with and created code for the Low-Layer API. The parameters were: LL_PWR_REGU_VOLTAGE_SCALE2LL_RCC_MSIRANGE_8 The function SystemClock_Config() of the generated code starts with void SystemClock_Config(void) { LL_PWR_SetRegulVoltageScaling(LL_PWR_REGU_VOLTAGE_SCALE2); LL_RCC_MSI_Enable(); /* Wait till MSI is ready */ while(LL_RCC_MSI_IsReady() != 1) { } LL_RCC_MSI_EnableRangeSelection(); LL_RCC_MSI_SetRange(LL_RCC_MSIRANGE_8); LL_RCC_MSI_SetCalibTrimming(0); LL_FLASH_SetLatency(LL_FLASH_LATENCY_2); if(LL_FLASH_GetLatency() != LL_FLASH_LATENCY_2) { Error_Handler(); } LL_RCC_SetAHBPrescaler(LL_RCC_SYSCLK_DIV_1); ⋮ The documentation (DocID024597 Rev 4, section 5.1.7 Dynamic voltage scaling management) reasonably states that the FLASH latency must be set up before the core voltage is changed. However the function SystemClock_Config() does it the other way aroun

Posted on March 09, 2017 at 12:10Hi all. I'm trying to read the eeprom I'm using the std_periph_library. I can send the address information to eeprom and get the ack bits correctly. I've connected pullups on the SCL and SDA pins. I'm using the I2C1 (I2Cx)const uint8_t DEVICE[] = {0xA0, 0xA4};const uint16_t WP[] = {GPIO_Pin_10, GPIO_Pin_11};&sharpdefine WP_PORT        GPIOB&sharpdefine WP_DISABLE(p) GPIO_WriteBit(WP_PORT, p, Bit_RESET)&sharpdefine WP_ENABLE(p) GPIO_WriteBit(WP_PORT, p, Bit_SET)&sharpdefine I2Cx_PIN_ENABLE() RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE)&sharpdefine I2Cx_SCL_PIN   GPIO_Pin_8&sharpdefine I2Cx_SDA_PIN   GPIO_Pin_9&sharpdefine I2Cx_PIN_PORT  GPIOB&sharpdefine I2Cx_CLK_ENABLE() RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE)void RMSNO_Init(void){ I2C_InitTypeDef i2c; GPIO_InitTypeDef gpio; NVIC_InitTypeDef nvic; gpio.GPIO_Pin = I2Cx_SCL_PI

Posted on March 24, 2017 at 14:38Everyone,I tried to run SDIO with RTOS, but never got luck,Any ideas why ?If I disabled RTOS, SDIO can run properly but if I enabled it, SDIO is stopped running..Thanks#freertos #sdio

Posted on March 30, 2017 at 18:47I see varying information about whether the timers in my STM32F437 are 16 bit or 32. Maybe I missed a table in RM0090 or the data sheet. Could someone please point me to a place where this info might be consolidated? So far by hit or miss it seems TIM2 is 32 bits and TIM4 is 16?Thanks,JH

Posted on November 23, 2016 at 17:30The absolute path of a CubeMX project is embedded in the .ioc file. This makes a little more difficult moving the project elsewhere or restarting with the project for example when retrieving it from a remote Git repository. It would be better having the option to keep the project location-agnostic and to regenerate the project-derived files in the directory which contains the .ioc file. #feature-request #stm32cubemx

Posted on March 10, 2017 at 14:55Hello All,I am using SPC560B540L5 Discovery board and SPC stdutio 5.2.3 updated version code generator.I am trying to emulate the Flash as EEPROM using EED driver. The IDE is installed with EEPROM emulation software and the way I generate the project is also proper even then the necessary configuration files and libraries for EED are not getting generated after generating the code. Normally, it should get listed under the EEPROM Emulation driver in components directory, but nothing exists other than ''mak'' folder. Please find the snap below.But still I tried to build the project but the compilation failed due to below shown error.I also tried with the Test application''SPC560Bxx_RLA EE Test Application for Discovery'' but the problem repeats.Even I tried with different versions of (SPC5studio) 5.0.0, 5.2.1 and 5.2.3 but nothings works.Kindly help in getting the problem resolved.Thanks in AdvanceRegards,R.Santhamurthy

Posted on March 27, 2017 at 19:20 HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_3); HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_1); HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_2); HAL_TIM_PWM_Start(&htim1,TIM_CHANNEL_4); __HAL_TIM_SET_COMPARE(&htim1,TIM_CHANNEL_1,40); __HAL_TIM_SET_COMPARE(&htim1,TIM_CHANNEL_2,80); __HAL_TIM_SET_COMPARE(&htim1,TIM_CHANNEL_3,120); __HAL_TIM_SET_COMPARE(&htim1,TIM_CHANNEL_4,190); //TIM1SETUP（cubeMX CODE）： /* TIM1 init function */ static void MX_TIM1_Init(void) { TIM_ClockConfigTypeDef sClockSourceConfig; TIM_MasterConfigTypeDef sMasterConfig; TIM_OC_InitTypeDef sConfigOC; TIM_BreakDeadTimeConfigTypeDef sBreakDeadTimeConfig; htim1.Instance = TIM1; htim1.Init.Prescaler = 24; htim1.Init.CounterMode = TIM_COUNTERMODE_UP; htim1.Init.Period = 200; htim1.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; htim1.Init.RepetitionCounter = 0; htim1.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE; if (HAL_TIM_Base_Init(&htim1

Posted on March 24, 2017 at 16:35I have a NUCELO board with STM32F767ZI.I have read that there are http://www.st.com/content/ccc/resource/technical/document/errata_sheet/group0/23/a6/11/0b/30/24/46/a5/DM00257543/files/DM00257543.pdf/jcr:content/translations/en.DM00257543.pdf on ethernet RMII, fixed in chip revision Z (see https://community.st.com/0D50X00009XkaTYSAZthread).How can I tell which chip revision my NUCLEO board is mounting?Thanksnull

Posted on March 28, 2017 at 10:35Hi,I have a STM32F334 with a cylindrical watch 32.768kHz xtal connected as a LSE oscillator. LSE now works. Folks on the forum, were kind enough to point out to me about possible PCB related issues.Originally, I've had a EPSON SMD crystal in there.Found a multitude of problems in there after digging into the issue, the first problem was a dead 32.768kHz crystal. Many trials later, tried the same crystal connected to a HEF4060 on a veroboard to test the crystal, which verified that the crystal was dead. Tried a cylindrical watch crystal with the HEF4060 and it worked. Tried the same cylindrical crystal in the same position, which did not work at all. The PCB design issue came to my mind, eventually stuck the crystal on top of the F334 and soldered the pins directly on to the F334.Unfortunately, this also did not help. After pulling out some hair, I found that for the LSE to be turned ON, the RTC domain had to be reset, which allowed the LSE to be turned

Posted on March 25, 2017 at 09:16Hi all, I have SPC56P-Discovery and I have setup UDE Visual Platform 4.8. But I'm not add key.Need for help!Thanks#spc5studio #pls

Posted on March 28, 2017 at 13:14Hello All,I am using SPC560B54L5 board. I am trying to make use of software Reset to boot up the MCU from start. Initially I tried to using DRUN mode but it didn't worked since it is getting stopped at irqSysHalt();Kindly guide me in triggering the software reset and executing the software reset service sequence#spc5studio #spc5x

Posted on March 24, 2017 at 17:58 Hi, I'm semi experienced with STM32, have been doing a lot of things. This issue is totally new to me: I'm trying the simplest thing ever, basic SPI, set as master, chip select managed by myself. Transmit works, clocking works, RXNE interrupt comes as supposed, but data register always reads as zero! The issue is only with SPI1; SPI2 (in different pins) works with exact same code! Done a lot of debugging, and reduced the issue to the minimal, super simple code: CPU: STM32F205VFT6 Clock config: SYSCLK at 120MHz, SPIs running at 30 MHz, but potential issues related to clock ruled out by running from 8MHz HSI divided down to 4MHz for SPI. This is the bare minimum initialization: RCC->AHB1ENR |= 0b111111111 /* PORTA to PORTI */;RCC->APB1ENR |= 1UL<<18 /*USART3*/ | 1UL<<14 /*SPI2*/;RCC->APB2ENR |= 1UL<<12 /*SPI1*/;GPIOA->AFR[0] |= 5UL<<20 | 5UL<<24 | 5UL<<28; // SPI1 alternate functions.GPIOB->AFR[1]

Posted on March 23, 2017 at 13:47I am using TIM2.CH2 input compare. No other interrupts are activated except TIM2.CH2. In TIM2_IRQ handler all IC bits except CH2 are set. Why?Using STM32Discovery on IAR. I expect TIM2_IRQ to fire up on trigger from outside. It does but CH2 interrupt ic leared and all other 3 IC interrupt bits are SET. Why?

Posted on March 25, 2017 at 09:27Hello everyone. I am using STM32F401RE Nucleo Board. I want to communicate with PC through USB CDC Virtual COM Port. I was following an instruction for STM32F4 Discovery and then I realized that my Nucleo Board didn't have a second micro USB port like his Discovery Board. Is it possible for me to make my own second USB port like Discovery Board on my Nucleo Board ? What should I do ? Thank you very much. 

Posted on March 22, 2017 at 22:54I ultimately need 'instant on' ADC conversions.  For instance, when a timing gate goes high, I need to start taking ADC values immediately (the signal is only 100us wide),  The problem I'm running into is the lag: firing up the ADC in DMA mode from a 'cold start' takes 50+ usec to start getting values.  I tried leaving the ADC/DMA running, and just enabling/disabling interrupts, but even that takes ~25us from the point of enabling interrupts to getting values out.The attached picture shows the dilemma: blue is the timing gate, yellow/purple is the signal I need to sample, and green is toggling when samples are being taken.  You can see that from the rising edge (when DMA interrupts are enabled) to getting samples takes ~25us. Now I've got the ADC/DMA dumping values into a 1000 element array (circular, continuous conversion).  That's working fine, but I need to be able to either 1: see what 'index' the DMA is pointing to in

Posted on March 23, 2017 at 17:49Hello,I use DSI with external 25MHz osc. In some design I wanted to useHSI (is seems supported wrt. ref.manual) but the DSI PLL doesn'tlock at all.I use IDF=3 to have INFIN=16/3>4MHz and NDIV=125, thus Fvco=666MHz.ODF=2 (/4) hence DSI clk is 166MHz. All is in correct range.With HSE, the only difference is IDF=4...Maybe, HSI is not stable enough ?M.#f7 #hsi #dsi

Posted on March 24, 2017 at 11:38Hello All,I am using SPC560B54L5 Discovery board(SPC560B-Discovery), SPC5studio version 5.2.3 and UDE Visual Platform 4.2 version.When I  try to load the application the .elf is working fine. If i try to make use of .hex or .bin file (as per my requirement)I am facing following problems,When I try to load ''.hex'' file the code gets loaded successfully but while running it is throwing an error as '' Unknown Break cause''. Similarly, when I try to even  load ''.bin'' file it prompts with ''Unknown File Format'' error.Error While loading .hex file:Error While loading .bin file:Kindly suggest if I need to do the changes to the settings or preferences in IDE (or) UDERegards,R.santhamurthy