Solved

HelloI am new to this forum, so if I am at the wrong place, let me know. How can this software: https://www.st.com/en/development-tools/stm32cubeclt.html be installed from a script? Namely into docker container? I get the following error: ``` DISPLAY not set. Cannot display license. Aborting. ```Thanks in advance.

I'm currently working on an STM32WB project and would appreciate guidance on the correct sequence to enter STOP2 low-power mode and wake up via an EXTI interrupt, ensuring all peripherals resume normal operation post-wake-up.Specifically, I’m looking for:The recommended steps to enter STOP2 mode, including any pre-conditions or configurations.The proper configuration for EXTI-based wake-up (I’m using a GPIO line for this).Best practices to ensure that all necessary peripherals (UART, SPI, ADC, USB, etc.) are correctly restored after wake-up.Any important considerations related to Core 2 (BLE stack), clock sources, or peripheral clocks that should be handled manually before or after STOP2.I’ve reviewed the reference manual and some ST examples, but a consolidated, recommended sequence or reference to an app note/code example that handles these aspects cleanly would be very helpful.Thank you in advance for your support!Refrence code:int main(void) { /* USER CODE BEGIN 1 */ /* USER CO

Dear allI am relatively new to STM32, using STM32H563 as an SPI slave to receive data and send some feedback data as same time, The SPI master is a Tiva MCU form Ti,  as data is relatively long, I need to use DMA, I tried to find an example for it, but there is none with DMA, could some one please provide some starting point for me? Thanks in advance.Ping 

In the STM32L4P5xx datasheet, some pins' IO structure is labelled with _l (in combination with other letters). However, this letter is not explained in Table 14 nor anywhere else.Can this please be explained?Thanks,JW

I'm having trouble enabling RTOS proxy for debugging. I followed the following tutorial:https://www.youtube.com/watch?v=iRaiMvYZ08oI get the following error:Error in final launch sequence: Failed to execute MI command: target remote localhost:60000 Error message from debugger back end: Remote replied unexpectedly to 'vMustReplyEmpty': timeout Failed to execute MI command: target remote localhost:60000 Error message from debugger back end: Remote replied unexpectedly to 'vMustReplyEmpty': timeout Remote replied unexpectedly to 'vMustReplyEmpty': timeout STM32CubeIDE v2.0.0STLink connected with SWCLK and SWDIO with up to date firmwareSTM32H725 custom boardTested on new project generated using CubeMXHere are my debug configuration settings:Please let me know if you require any additional information.Thanks in advance!

I am testing power consumption. The hardware is using nucleo-L476 and X-NUCLEO-NFC08A1, and the software is using the NFC06A1_PollingTagDetect routine from X-CUBE-NFC6. The test revealed that the average power consumption was 180 uA when entering the wakeup. I was using a 3.3V power supply. The minimum current is 40 uA.I'm not sure how to make the necessary modifications to achieve the description in AN5320. 

Hello everyone,I’m working with the 1N5822UB1 Schottky diode and need forward current (If) vs forward voltage (Vf) characteristics at -55°C. The datasheet only provides graphs for 25°C, 100°C, and 120°C, but my application requires performance data at -55°C.Does anyone have a graph or table for If vs Vf at -55°C?Any guidance or resources would be greatly appreciated.Thank you!

Hi you all,as a breef summary; I set up a timer to trigger an adc that should than use the DMA to transfer the data to memory, i need 111 samples at a time. Sadly for some reason this only works for one sample so if i check  __HAL_DMA_GET_COUNTER(g_hadc1->DMA_Handle) it will get stuck at 110.and subsequently my  HAL_ADC_RegisterCallback(g_hadc1, HAL_ADC_CONVERSION_COMPLETE_CB_ID, ADC_LineScanComplete_Callback); is never called.Though the timer and ADC for sure triggeres as i can the see the DR register updating its value.And as far as the reference manual goes (Page 961 DMA One-shot) it should be possible to use  HAL_ADC_Start_DMA(g_hadc1, (uint32_t*)dest, 111); to get like 111 sequential timer triggered samples, that are transfered to memory via DMA I tried various combinations of all possible adc settings, and all of them keep beeing stuck on 110 remaining DMA cycles. As well as trying to look up the resgisters for any errors that might have been accured, but

MCU: STM32H7S7L8H6HIssue: Choppy scroll animations after regenerating TouchGFX/target/generated in CubeMX files with TouchGFX 4.26 (previously 4.24.1 or 4.25)SymptomsScroll wheel with custom containers (toggle buttons + text) now shows low FPS when swiping. The same widget was way smoother before regeneration. I have a device with old generated files still running smoothly, confirming the regression is in the regenerated target code (check video, the smoother one is the bottom one).Unfortunately, I haven't git the  TouchGFX/target/generated because I thought it was being generated by TouchGFX Designer and not CubeMX, so I have no idea what code it was running before. Sure thing is, the scroll wheel logic in the GUI folder is the same for both things.I was already using TouchGFX Designer updated to 4.26 when everything was smooth so, I think the file generated by it are ok.What ChangedRegenerated via CubeMX, replacing:nema_hal.cOSWrappers.cSTM32DM

Hello,I want to ask if it is possible to install STM32Cube extensions into Cursor.I looked in the normal extension list but I could not find them.Is this supported now or will it be supported in the future?Thank you.

I am currently using the X‑NUCLEO‑IHM16M1 expansion board and noticed a discrepancy between the Motor Control Workbench and the official ST documentation regarding the rated current.In Motor Control Workbench, the Rated Current is shown as 2.1 A.On the official product page and data brief, it states Output current up to 1.5 A rmshttps://www.st.com/en/evaluation-tools/p-nucleo-ihm03.html Could you please clarify the following:What is the basis for the 2.1 A figure shown in Motor Control Workbench (e.g., RMS, peak, or internal limit)?Which current rating should be considered as the actual board limit for design purposes?Does the difference relate to the STSPIN830 driver’s internal specifications or to a configuration setting in the tool?Thank you very much for your support.Best regards,HyeonSeok​

M95P16 data sheets says chip erase cycle is 100, but an5866 says chip erase counts as a cycle every page. Which is correct? Datasheet:AN5866:

I have managed to create a template application on a NUCLEO-H755 that has several CM7 FreeRTOS tasks running to flash various LED patterns combined with a CM4 application that flashes one of the other LEDs.  I have mainly been testing using a run configuration (with LEDs to verify behavior), but sometimes a debug configuration, and when working, the program behaves well and runs overnight.  Flashing and starting the code has always been somewhat questionable (likely due to my inexperience with STM32CodeIDE (V 1.19)), but recently I am no longer able to successfully Run or Debug at all.The current behavior is as follows:1) The first time I try to Debug (or Run), I get a "Failed to execute MI Command" with the error indicating failure to finish loading the flash for the CM7.elf.2) The second time I try the same Debug or Run command, I get a "Failed to Start the GDB server", and I am not able to communicate with the ST-Link on the NUCLEO at all.3) The only way that I have been a

Hi Team, It appears that the varistor turned on at a voltage lower than the value specified in the datasheet.・​Detailed V-I characteristics of the varistor・​How significant is the variation between individual varistors?・Once a varistor turns on, does it remain on even after the power is turned off?・What is the tolerance of VBO?​・Does the failure mode of this varistor result in a short circuit?Thanks

Greetings,I'm trying to run an application using X-CUBE-ST67W61, but I'm encountering a problem at this line in w61_at_common.c: int32_t W61_AT_ModemInit(W61_Object_t *Obj) { (...) xReturned = xSemaphoreTake(mdm->sem_if_ready, pdMS_TO_TICKS(4000)); (...) } everytime, xReturned equals 0, which means that sem_if_ready is not received.My setup consists of STM32N6570-DK with X-NUCLEO-67W61M1, and the code I'm trying to run is mostly ble_p2p_server app from X-CUBE-ST67W61. Some of the SPI communication starts, as seen below: but these are the only signals that are appearing.

Hi ST team,I am using STM32U5G9 MCU. After modifying option bytes, HAL_FLASH_OB_Launch() would be called to apply the changes.But in the launch function, it states that "Option byte launch generates Option byte reset". I have other tasks need to be done after calling HAL_FLASH_OB_Launch(). I don't want device to be reset after calling HAL_FLASH_OB_Launch() immedately.Is there a way to trigger reset manually after modifying option bytes?1. Modify option bytes2. Call HAL_FLASH_OB_Launch()3. Reset device manually Thank you.

I am using ST25R3916B with differential antenna without varicaps.The antenna is configured to receive maximum signal  from the smartphone on the RFI1.There is a TFT display between the antenna and the smartphone. The smartphone reads the tag with great difficulty even when pressed against the display.The ST25R3916B reads cards in card reader mode at a distance of about 2 cm from the display (when setting up the antenna to get the maximum signal from smartphone).Question: How can I increase the tag's reading range with my smartphone? ST25R3916B has sensitivity control registers, but there is no method for setting these parameters.Best regards.

I have a STEVAL-MKBOXPROm and I flashed "STM32CubeFunctionPack_DATALOG2_V3.1.0"  (DATALOG2_Release.bin) to it. In the ST BLE App, I can start and stop an acquisition, edit which sensors are logged, and edit the fillenames. However, the acquistion_info.json file does not show my updates Acquisition Name, Description, or any of the Tag Names. I tried rebooting my phone and the device. Anyone have any suggestions?

Hello,Is the STM32CubeProg + STlink (v3) supposed to work with STM32MP257 ?I can't get any connection.Thank you 

Hi!I’m working on a motor controller design that utilizes an stm32f4 and a magnetic angular position sensor which communicates via spi.My design currently performs current sensing; I use channel4 of timer1 to trigger ADC reads near the center of my center-aligned UVW PWM period.This works great so far, but now I’m trying to think through how/when to schedule SPI reads of my angular sensor. I can straightforwardly perform an spi read when the ADC conversion completes, as part of my inner torque control loop. Is this reasonable to do? Is there a better way? It seems like the best time to touch off such a read is at the same time as when I trigger my ADCs. But I can’t quite figure out how I might do this.Thanks!

Hello. I am currently working on a NUCLEO-L152RE project in the latest version of the CubeIDE. I am running into an error where I can not install break points due to an "unmatched quote". I have tried the common fixes (New work space) for this that I could find online and it hasn't resolved it. I also ran fresh installs of the programs and encountered the same issue. Has anyone else encountered this problem? I have included a screenshot below for reference.   

Hi,I made a custom bootloader to upload my application using the virtual com port by the USB interface.This works nicely, but my application also has a part in flash to store its configuration. When I flash my user program, I do not want to overwrite the configuration. Therefore, this is a special part in the flash memory.Is it possible in the STM32CubeIDE to generate a bin-file for this configuration to have a default configuration?Is it also possible to generate a bin-file using my bootloader, by reading the flash memory where the configuration starts? Because it would be great to backup a configuration.Greetings,ErX  

P-NUCLEO-WB55Just a sanity check really.I'm using the DWT unit to time a chunk of code, am I right that each tick is at 1/32MHz?

I am entering the world of NFC with a somewhat complex project, but I took the initiative to start it. The goal was to create a sensor that would work only with Energy Harvesting from the reader.For this, I chose the ST25R300 chip to be the chip for my reader board and sensor power supply, mainly due to its high transmission power.I am having difficulty getting it to work properly. Basically, I ran several tests with some DEBUG codes on the reader board. In these tests, I found some inconsistencies. The first is the VDD_A voltages, which come from a reading of the chip itself, which is registering almost 6V, and the other inconsistency is the RSSI giving 0.I believe the error is in my antenna and matching circuit. I would like someone to help me improve this system by pointing out where I may have made a mistake in their design.I made the antenna using the ST website (eDesignSuite antenna design tool). I also made the maching circuit using ST's eDesignSuite.In addition, my circuit was

Hello STI would like to ask about is it possible to change the STUSB4500 FTP_KEY default values through SMBUS interface? If its possible, could you suggest the appropriate step to do so?