Solved

SummaryAt the end of the day, my issue is missing something in documentation. The lesson here, is test thoroughly. Just because it works for a few minutes, doesn't mean forever. Anyway, I've been running >3mA through the pins that are limited before of this "power switch" thing. I was wondering if anyone knows more about and how/why these pins are connected like this?DetailsI'm running two different boards with the same chip (STM32L431) and firmware. I have some debug LEDS on my board that flash 1sec on, 1sec off in open-drain configuration. In one case its an RGB led where I flash blue and green (10mA each)In the other case its a while LED that shares the same 2 pins (20mA total)Over time, it seems that this eventually burns out the MCU (first getting hot, then breaking all together). According to DS11453 Table 20. Current characteristics, you can easily run LEDS like this.  However!. I chose were PC13, PC14 and PC15. While is says Nothing at all about this in Electrical Chara

Please help to find out whether STM32L011F3U6TR mcu boot0/PB9 pin has internal pull-up/pull-down resistor feature. There is no mention that boot0 pin is special in this respect, ie no internal pull-up/pull-down resistor.  On my board, unable to bring this pin high even though boot0/PB9pin is configured with pull-up resistor. Any workaround fix if it doesn’t have.

Hello, sorry for asking this but I'm new to operating STM32 microcontrollers and the IDE it came with. I wrote a simple code to read the pin state and write to an LED once detected. All runs well on debugging. The problem for me is that when I unplug the USB connection (the board is powered through a power supply) the code suddenly stops and no LEDs light up after the button is pressed.Is there a step I'm missing like compiling to memory? I've spent some time looking for an answer but sadly I got no luck in solving this. If possible, could someone lead me towards finding a solution for this? Thank you :)

..

I have configed the FLASH_CR，SET_BIT(FLASH->CR, 1<<27);I want to know how to clear bank1 securable area.

Calling the ai_instrumodel_data_weights_get() function has problems with the AI_BUFFER_OBJ_INIT struct in "ai_platform.h". I'm following this guide exactly step by step: https://www.digikey.com/en/maker/projects/tinyml-getting-started-with-stm32-x-cube-ai/f94e1c8bfc1e4b6291d0f672d780d2c0What I don't understand is the fact that an initialization tells me that it has no members. What is this based on to claim this error? It's defined right there, i should be able to define whatever I want. That's like saying "int i = 0; is undefined". No, it's defined right here. To reproduce, copy the code in the link and run it with Cube IDE 1.7.0 and X Cube AI 7.0.0

2021-08-17 09:46:33,673 [1] INFO TouchGFXDesigner.App: Logging configured2021-08-17 09:46:55,655 [1] INFO TouchGFXDesigner.Main.MainWindow: Application started2021-08-17 09:46:55,656 [1] INFO TouchGFXDesigner.Main.MainWindow: Username: nodemis2021-08-17 09:46:55,656 [1] INFO TouchGFXDesigner.Main.MainWindow: Designer version: 4.17.02021-08-17 09:46:55,656 [1] INFO TouchGFXDesigner.Main.MainWindow: Designer installation path: E:\TouchGFX\4.17.0\designer2021-08-17 09:46:55,656 [1] INFO TouchGFXDesigner.Main.MainWindow: Windows version: Microsoft Windows NT 6.1.7601 Service Pack 12021-08-17 09:46:55,656 [1] INFO TouchGFXDesigner.Main.MainWindow: Current culture: tr-TR2021-08-17 09:46:55,671 [1] INFO TouchGFXDesigner.Main.MainWindow: Current culture time seperator: :2021-08-17 09:46:55,671 [1] INFO TouchGFXDesigner.Main.MainWindow: Current culture date seperator: .2021-08-17 09:46:55,720 [1] INFO TouchGFXDesigner.Main.MainWindow: Installed

Hi,I working Stm32f767zi mcu with HMI screen and I need to make communication using RJ45 interface using tcp ip. I need to know that which example is works for it, I have searched and checked a tcp ip server example code to get new incoming hmi connection on stm32f767zi RJ45 jack.But little confused between the connection setup and the selected example for working & testing initially.I request you to please confirm my above setup, if I am going wrong and please suggest proper way to start communication between stm32f767zi rj45 jack to hmi rj45 jack direct connection.Looking forward for the support.Thanks & Regards

Are here any example projects on how AcousticBF library should be configured exactly for PCM mode? There are plenty of examples for PDM mode configuration, but none for PCM, which is frustrating, since the documentation on this library is not very explicit.When I'm trying to configure it, AcousticBF_FirstStep function fills only 1/3 of the output buffer, so the output sound is very distorted. Any help is appreciated.

I purchased P-NUCLEO-53L5A1 including X-NUCLEO-53L5A1 and NUCLEO-F401RE.And I assembled them and connect to PC, and then I installed its driver and reboot windows 10.When connecting, the explorer open the mass storage drive (D: (F401RE)).However, VL53L5CX GUI shows no list of VL53L5CX using X-NUCLEO-53L5A1 as the belowEven after pressing the refresh button several times, the result was the same. I changed the driver's port number from COM15 to COM2.It's because COM1, COM3~COM15 were already used.After this, the result was the same.When I use X-NUCLEO-53L0A1 instead of X-NUCLEO-53L5A1, VL53L0X_GUI works well.Even after changing NUCLEO-F401RE with X-NUCLEO-53L0A1's instead of X-NUCLEO-53L5A1's, VL53L5A1_GUI shows no list.Even after updating ST-Link, VL53L5A1_GUI shows no list.Even after copying 53L5A1_MultiSensorRanging.bin to D:, VL53L5A1_GUI shows no list.Why does this happen? Is X-NUCLEO-53L5A1 broken?Thanks in advance.

Hello,​I experienced a phenomenon in which the USB port was not reconnected.This phenomenon occurs when a USB port is connected to the product and reboots.​I check my device manager. When i turn off product, com port also disappear.and product reboot then com port appear.But i can't receive any data.When i reconnect USB cable then communication work well. ​SummaryUSB virtual com port can't receive data when device reboot.In the same state as above, USB cable reconnect then USB connect well. I need your support.Thanks. best regards.​​​

Hello! I am trying to simulate an octave model on a microcontroller and ran into a snag I thought I'd get some help with. So I have an FFT I am running on a sample of data (we'll say 4096 bytes). In octave, I'm using an FFT of the sample (where the sample is a 1 x 8192 array):fft_data = fft(sample);Pretty straight forward function. I have the data extracted to a csv file for comparison to ensure the data matches up. I am now trying to replicate the fft on a microcontroller. I thought I had set it up correctly from a few forum posts but I can't tell if I'm using the wrong type of fft, the wrong data size, etc. Below is essentially what I have on the microcontroller:float32_t sample_flt[4096] = {0}; float32_t fft_out_buf[4096] = {0};   arm_rfft_fast_instance_f32 fft_handler; arm_rfft_fast_init_f32(&fft_handler, 4096);   arm_rfft_fast_f32(&fft_handler, (float32_t *)sample_flt,(float32_t *)fft_out_buf,0);When I'm looking at the contents of the sample, I'm getting sample[0

HiThe new dynamic graph widget is great, but is there a setting / different graph widget that will allow me to plot data based on a set of coordinate points (x and y)?For example, with the dynamic graph widget there is an addDataPoint(y) method. Is there a similar method for plotting data that doesn't have fixed x coordinate intervals?Thanks

..

I had STM32WB55CGU7 chips with original factory FUS version 0.5.3. I upgraded it to version 1.0.1 successfully, then I tried to upgrade to latest released version 1.0.2, but I get "Error: Firmware not authentic!"

In former CubeMX versions an Clock to ADC of 400MHz was possibleNow I am working on CubeMX V 6.3.0 with STM32Cube FW_H7 V1.9.0.The maximum Clock frequency I can adjust is now 79MHz (selected clock source is the PLL2) What is the meaning of the "79 to ADC (MHz)" exactly.If, it is the input for the prescaler of the ADC, why it is limited to 79MHzWenn > 79 MHz is selected, CubeMX shows an error.If it is the maximum Clock frequency of the ADC, why is it not limited to 50Mhz as discribed in the datasheet for the V designV-design is also selected

I see that ODR mentioned in datasheet is 26.7Khz but my doubt is that whether it is in each direction (x,y,z) or combined for all 3 axis. This is because when i try to measure the time taken to take samples then i get it around 9000Hz in each direction. I am using data polling technique via STM32 F4 controllerIf it is so then how BW of 6.3Khz is achieved 

Hi all,I am using a STM32G061C6T6 MCU. I'm trying to contact Nextion HMI. My data sending is successful, but I can't get any data. I couldn't run any of the Pooling and interrupt methods when receiving data. When I follow the RX pin with the oscilloscope, the data comes, but I can't read it with MCU.  I tried the display on the Nucleo-F103RB card with a simple HAL code. I can read the data from the screen. Do I need to do a special operation on this MCU(STM32G061C6) to be able to read with UART? I'd appreciate it if you could help me.#include "main.h"   /* Private includes ----------------------------------------------------------*/ /* USER CODE BEGIN Includes */   /* USER CODE END Includes */   /* Private typedef -----------------------------------------------------------*/ /* USER CODE BEGIN PTD */   /* USER CODE END PTD */   /* Private define ------------------------------------------------------------*/ /* USER CODE BEGIN PD */ /* USER CODE END PD */ &

I am using SPC58EC MCU board to send some through Ethernet , For this one I tried to generate new project inside that I selected the network section , Inside I choose ping project.Can any body suggest how to configure Ethernet driver?

..

Hello,I have an IOC file, which was generated with help of STM32CubeMXMxCube.Version=5.6.1MxDb.Version=DB.5.0.60When I open this project to update the Keil project (which has Keil Compiler version 6 selected), with STM32CubeMX version 6.0.1 (with STM32Cube MCU Package for STM32H7 series version 1.8.0), and generate code, the STM32CubeMX deselects the MicroLIB check box.I am observing the code is not behaving as expected with MicroLIB disabled / unchecked.As the issue is not observed when using the ULINKpro debugger (which I am using to find the reason for the issue) I am unable to find the reason for different behavior of the same code just based on whether the MicroLIB is in use or not in use.Please help with resolving my concern.Thanks,Rajeev

Hi all,On a M24SR series NFC tag, after writing a NDEF message I need to activate GPO pin to wake up the MCU. On Android with java, this method exists: activePinGPO(NFCTag tag, OnNFCListener listener);And I'm trying to find the same method for iOS. Just for be more precise, I'm using NFCISO7816APDU to send messages. So I'm wondering if I can manage GPO pin with APDU as well because it's not written on the datasheet.Any idea?Thanks!

Hi,I'm getting a lot of errors in SPC5Studio. If I use it with main.c without separating the library directory I'm working in, I don't have a problem. But when I want to separate the libraries, it doesn't work like an ordinary eclipse. Likewise, I don't have any problems with STM32CubeIDE, but SPC5Studio gives a lot of errors. The errors I get are:make -j8 allCompiling main.cmain.c:4:21: fatal error: nextion.h: No such file or directory #include "nextion.h" ^compilation terminated.make: *** [components/spc560bxx_platform_component_rla/lib/rsc/rules.mk:137: build/obj/main.o] Error 1"make -j8 all" terminated with exit code 2. Build might be incomplete.For example, when I write the library I have reserved as nextion.h directly into main, it works. I will share with you the settings I made and the library I created. Regards.

I've changed the .ld file for STM32G474 generated by STM32CUBEIDE.The part of old .ld file is like this,I added ">RAM AT" at the last line like this,But when I'm debugging,the code is running into the HardFault Handler.I want to know if something else need to be edited.

Hi,Where can I download STA8089GA reference schematic and application notes?Thank you.