Solved

Hello Community,I am new in the topic of nfc and programming of nucleo boards.So, the questions can seem to be very stubid ;)For a project I try to bring up a X-Nucleo-NFC06A1 on top of a Nucleo -F446RE.On web (ST,...) I found code examples for different nucleo boards.If I import the supported examplary projects into the Cube IDE, everything works quite well...but with the wrong Nucleo board.I can't find any guidline to bring up the NFC extension board with the F446RE.And also the NFC06A1 cannot be imported via Devcie config Tool (software packets).So my (stupid) questions:Is there a guidline / video / ... available which describes the steps to port the existing examples to the f446reWhat files of the Middleware/Driver should be included to get the NFC06A1 running in from a default F446RE projectHow should the f446re be configured (SPI,...)Thanks for every helpfull comment,Sebastian

Hello all.I'm gonna work with my MCU flash memory (SPC560B54L5).I installed driver and samples from link below:https://www.st.com/en/embedded-software/spc56xmbp-flash.htmlBut c-array-drivers and also its samples are compiled with Diab and GHS but i am working with SPC5Studio which is GCC.My second question is about Flash Reading?!Is there any way to read flash memory ? (I have not found any function or API to read flash memory)

I am using the STMCubeIDE version 1.8.0I try to create a STM project for a STM32f407VEI get the error message as many users : the IDE does not find the 1.26.2 firwareI tried to follow the solution to install with the Import from local option, this does not workI tried to install and use the 1.26.0, the packages installs correctly in the "manage packages" but is not detected by the "create project" option (it tries to download it again)I followed the answer here: https://community.st.com/s/question/0D53W000004k3VCSAY/solution-error-in-stm32cubemx-or-cubemx-inside-stm32cubeide-for-add-new-firmware-or-new-patchoffline-or-onlineBut this doesn't work for me.Can you help me ? This is my first experience with STM32IDE and I don't understand what is going wrong.Thanks

Is it possible to use STM32H743's LTDC with no frambuffer and fill its FIFO "on the fly"?

When compiling the U-boot, these four commands are used:PC $& gt; export KBUILD_OUTPUT=.. /build/stm32mp15_trustedPC $& gt; export DEVICE_TREE=stm32mp157c-dk2PC $& gt; make stm32mp15_trusted_defconfigPC $& gt; make alluse the first: export KBUILD_OUTPUT=.. /build/stm32mp15_trusted, the compiler will fail, but if there is no first statement, the compiler will succeed

Is there a way to disable STMCube IDE from constantly stealing focus? I'd rather get to it when I'm done with another window than be interrupted Clippy style ;)

..

..

..

..

..

..

..

..

..

..

Hi all,Someone has a working example of simple communication via Ethrnet TCP between linux and freertos with the SPC58EC.Thnaks in advance

we have the flash driver "SPC58XEC-FLASH" downloaded from the link: https://www.st.com/en/embedded-software/spc58xec-flash.html, the version is 0.2.1.we have used it to program the device SPC58NH92C3 successfully, now we have a new device SPC58NN84E7RSHRR, did this driver could still support this device?

Hi,I'm using an STM32L496G board, currently flashing it through CubeMX/Touchgfx Designer.In the future, i'd like to be able to flashthe board by running a bash/python/other script from a linux machine. The board will be connected to the linux machine via uart.I'm not sure how to do that, and I wasn't able to find helpful instructions online.I'd appreciate your help.Thank you!

If it is a scaled fraction then how does it get filtered from transient changes of the Vdc supply?If it is a fixed constant voltage then the outputs will be biased at that same voltage and peak output audio will be clipped non-symmetrical. For example, if Vdc supply is 18Vdc and Vref is 5Vdc then the output can swing from 5 to 18V ( a change of 13V before clipping) and the output can swing from 5V to ground (a change of only 5V before clipping). This would severely limit the low distortion power rating.

Here are the details on MCO1 pin configurations, GPIO_InitStruct.Pin = LL_GPIO_PIN_8; GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE; GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_HIGH; GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL; GPIO_InitStruct.Pull = LL_GPIO_PULL_NO; GPIO_InitStruct.Alternate = LL_GPIO_AF_0; LL_GPIO_Init(GPIOA, &GPIO_InitStruct);Below is MCO1 clock configuration: LL_RCC_ConfigMCO(LL_RCC_MCO1SOURCE_HSE, LL_RCC_MCO1_DIV_5);External HSE on STM32F769I-Disco board is of 25Mhz.So expected signal on MCO1 (PA8) is smooth square wave with 5 MHz frequency.but I am getting signal with variation in amplitude as shown in the attached Image file.Please, do guide me if anything is missing in the configuration or attached waveform is expected and need to be handled outside for filtering a amplitude values.Thank You,Deep darji.

I have been using the WB since it was alpha release 0.x.y and so I have a long-established proprietary app running on the STM32WB55RG Nucleo board. Using the BLE full stack, configuring the GAP role as (GapRolePeripheral | GapRoleCentral) and subsequently advertising and scanning (both separately and simultaneously/synchronized intervals, obviously). After all advertising/scanning and connecting (as a master and/or slave) are finished, the proscribed protocol is followed to enter STOP2. But starting with v1.12 (and repeatable in v1.12.1) the current draw is higher in STOP2 after advertising.To be sure, current draw is lower than during advertising, and for sure over-the-air advertising does stop when it is requested, but STOP2 current draw is never as low as expected.This observation is made only after starting and stopping advertising after powerup and initialization. So scanning can be turned on and off and STOP2 is as expected. Advertising can be turned on, a connection as a slave r

Hi STM Community,I would like an answer from STM about the status of I2C in the HAL drivers.Basically, they are broken, and still broken in STM32CubeIDE-1.7.0.Of the many issues, there is still an open one here: https://github.com/STMicroelectronics/stm32l0xx_hal_driver/issues/5 and in fact even the examples provided don't actually work either (due to these issues with the _IT and _DMA functions).For instance:HAL_I2C_Slave_Receive_IT and HAL_I2C_Slave_Receive_DMA never call HAL_I2C_SlaveRxCpltCallback or any other callbacks for that matter (I've tested this exhaustively), ever, making them unusable in practise. This desperately needs to be fixed.Confusingly HAL_I2C_Master_Transmit_IT and HAL_I2C_Master_Transmit_DMA DO work, and DO call HAL_I2C_MasterTxCpltCallback.Is there an actual effort on STM's behalf to fix these functions, and actually test their OWN API's with hardware?If so, is there a time-frame for these glaring issues to be fixed?Has anyone ACTUALLY been able to get these si

​I am using P-NUCLEO-WB55.I set 3 buttons (SW1 / SW2 / SW3) to GPIO_EXTI. I confirmed that an interrupt is generated when the button is pressed.After that, if the middleware STM32_WPAN (BLE) is enabled, no interrupt will occur even if the button is pressed.How can I use GPIO interrupts with STM32_WPAN enabled?

I am using 3 Channels to generate 6 pwm using complementary pwm by timer 1.I want to control output of CH1 and CH1N seperatly.I tried configuring according to this table:TIM1->CCER &= (uint16_t) ~TIM_CCER_CC1NE; // Disabling compl pwmHAL_Delay(15000); TIM1->CCER|=TIM_CCER_CC1NE; // Enabling compl pwmEnabling compl output again does not work.The output is disabled and never get enabled again.can someone help to configure bits.I am doing something wrong.How to configure bits to enable and disable output over fly ?