Solved

The error occurred while reading a UART interface (heavy load @ 115200 baud) byte by byte (with HAL_UART_Receive_IT(&huart1, &com_uartRxSignBuffer, 1) ). MCU: STM32F302VB ST firmware version : STM32Cube_FW_F3_V1.11.2Before the RXNE interrupt is disabled when 1 byte is received, the interrupt can be re-triggered by another received byte.If this happens when huart->RxXferCount is already counted down to 0, huart->RxXferCount is counted down again. An underflow occurs, obviously the RXNE interrupt is not disabled, and the following 65535 bytes are written to com_uartRxSignBuffer[0 ... 65535].Almost certainly this will overwrite a pointer. By accessing it, an invalid memory address is accessed, resulting in a hard fault.The code (I have commented the places where this underflow occurs) that triggered this error (stm32f3xx_hal_uart.c line 3800): /* Check that a Rx process is ongoing */ if (huart->RxState == HAL_UART_STATE_BUSY_RX) { uhdata = (uint16_t) READ_REG(huart-&g

Hello guys, I am working with STM32MP157C-DK2 board and Tapo C200 camera(ONVIF). I would like to display the IP camera live feed through the LCD screen.How can I do that? I'm still a newbie, so step-by-step process or any link towards a good documentation regarding this would be nice :)

Hello everyone,I'm using the STM32H7 and the new fully reworked ethernet driver along with the LWIP and FreeRTOS for sending and receiving the UDP packets. The issue is first two packets get corrupted when sending. I don't send the UDP packet with zeroes in the payload, but the first sent packet is filled with zeroes.I've tried placing a delay in case the Ethernet is not properly initialized but that didn't fix anything.I suspect that the memory gets corrupted, but cannot prove anything.Does anybody know what could be the potential issue here?Thanks

I have downloaded all the needed software and st-link (and update) but Unicleo_GUI does not recognize the expansion board. In my device manager, the virtual COM is there. I am able to connect to the right port, but only if I tick the box that lists all the COM ports. Any help is much appreciated. Thanks

Hello, ​I am working on ST25RU3993 STUHFL SDK package v3.1.0.0 to run the STUHFL_demo applications on a Raspberry Pi 3 Model B V1.2 device. Following the instructions specified in the user manual (UM2618), I compiled the middleware source files on RPi 3B using the makefile provided. The installed gcc version and the kernel version of RPi 3 which I've worked on are as follows, respectively:gcc (Debian 10.2.1-6) 10.2.1 20210110Linux raspberrypi 5.15.32-v8+ #1538 SMP PREEMPT Thu Mar 31 19:40:39 BST 2022 aarch64 GNU/LinuxThen, I compiled STUHFL_demo application as well without any errors although there are some casting and conversion warnings. And, I was able to generate the executable named as STUHFL_demo.out. Upon running the executable, the ST25RU3993-HPEV board is recognized successfully but after a while, occurs a segmentation fault and the application exits. I also ran Python script named STUHFL_demo.py after placing the libSTUHFL.so file to the appropriate path. Unfortunately, I enc

Hello,On my project I want to change font of a TextArea according to some value.First of all I created a topography to apply in TouchGFX.I guess this is the good way to do.Secondly I wondering how I can apply it on my TextArea ? How find the typography name and how to apply it ? I tried something like that :Cont_LM_Simple_2_txt_lift_current_kg.setTypedText(touchgfx::TypedText());But I didn't not managed to find how to set up my new typography.[EDIT] Code insert

Hello, I'm working with an STM32G05, on a very simple custom board. I expose both USARTs to external headers.USART1 seems to be operating fine - in that I can send/receive data.However, USART2 is not.When I inspected the TX line I discovered it was low, even at boot.I check for anything that might be pulling it to ground, and there isn't anything on the board itself. Is there something with the processor that could be causing this?

I'm trying to piece together the post-build process for flash integrity check using CRC. I'm running on an STM32F777.So far I've been following:https://community.st.com/s/question/0D50X0000B9vdDC/how-can-i-calculate-crc-of-image-in-post-buildand https://www.eevblog.com/forum/microcontrollers/stm32-hex-file-signing-with-crc/andhttps://github.com/ethanhuanginst/STM32CubeIDE-Workshop-2019/tree/master/hands-on/06_F746-DISCO-CRCBut I'm seeing an error (warning?) that these guides don't mention and I haven't been able to find an explanation elsewhere:warning: The STM32 filter uses 4-byte alignment,  but unaligned data is present. Use a "--fill 0xNN --within <input>  --range-padding 4" filter *before* the STM32 filter to fix this problem. See  srec_info(1) for how to see the data ranges.I've tried adding the changes suggested by the error message, but they throw additional errors and it feels like a rabbit hole.What's causing this unaligned data? Can I/shou

Hello,I'm trying to do the memory position jump using this code:JumpAddress = *(__IO uint32_t*) (APPLICATION_ADDRESS + 4); Jump_To_Application = (pFunction) JumpAddress; __set_MSP(*(__IO uint32_t*) (APPLICATION_ADDRESS )); Jump_To_Application();I managed to make it work with only one GPIO, but when I add peripherals in the bootloader, it no longer works.I'm trying to de-initialize the peripheral, a UART has this reference (stm32f4xx_hal_uart.c):/** * @brief DeInitializes the UART peripheral. * @param huart Pointer to a UART_HandleTypeDef structure that contains * the configuration information for the specified UART module. * @retval HAL status */ HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart) { /* Check the UART handle allocation */ if (huart == NULL) { return HAL_ERROR; }   /* Check the parameters */ assert_param(IS_UART_INSTANCE(huart->Instance));   huart->gState = HAL_UART_STATE_BUSY;   /* Disable the Peripheral */ __HAL_UART

Hello!I am trying to run ping on my board with STM32H745 (similar to NUCLEO-H745ZI-Q). Instead of the standard LAN8742, I have to use KSZ8081RNA. On the advice of @Piranha​ and @Pavel A.​ in other branches, I leave almost everything as it is in the LAN8742.c driver, I change only some registers in order for initialization to be successful (I only needed to change the LAN8742_GetLinkState function). I can read and write KSZ8081RNA registers. I see in debugging a link change when connecting/disconnecting an ethernet cable.But ping data packets (ICMP) are still not coming to me. The program does not pass /* Check if descriptor is not owned by DMA */ check (HAL_ETH_Read Data in the file stm32h7xx_hal_et.c line 1063) due to the values of the descriptors heth->RxDescList.RxDesc. It is equal to 0x81000000. In another, working project, it is equal to 0x3401003С.Most likely, I did not fully initialize correctly, because the same project worked on NUCLEO-H745ZI-Q before the changes.

I am capturing an RC PPM signal using an advanced timer with DMA. But now, I want to implement a failsafe in case of a lost connection using only hardware. The closest I got so far is using a separate timer (with pins connected externally) in reset mode, so the counter restarts when an edge is detected. I am using the timer update interrupt to know when the counter period has been reached. This works, except that the act of resetting the counter also triggers this interrupt. I want an interrupt only when there has been no activity on a pin for an amount of time.

Hi guys,I'm struggling with modem communication on embedded system that does few other tasks in realtime. I'm using TCP stack built in modem (Fibocom G510). This seem to be not complicated, but every time I'm doing it - I'm doing it diffrent way and I end up with pretty big and not perfect code, because there is always URC or condition that I have not thought of.To establish TCP socket connection I have to:- reset modem hardware- wait for "SIM READY"- enter pin (optional)- wait for cellular network registration- wait for 2G/3G/4G registration- configure APN- configure other things (optional)- activate internet connection- activate TCP connectionAfter everything is initialized and connected I have to handle many things, including URC (unsolicited result codes):- cellular network connection lost (so AP and TCP connection is also lost)- AP connection lost (so TCP connection is also lost)- TCP connection lost- maybe even SIM LOST scenario- errors- incoming data from TCP socket- incomi

Enable both USART1 and USART2.The code generated for initialization of the GPIO looks like this:void HAL_UART_MspInit(UART_HandleTypeDef* uartHandle) {   GPIO_InitTypeDef GPIO_InitStruct = {0}; RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; if(uartHandle->Instance==USART1) { /* USER CODE BEGIN USART1_MspInit 0 */   /* USER CODE END USART1_MspInit 0 */ /** Initializes the peripherals clocks */ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1; PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK1; if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { Error_Handler(); }   /* USART1 clock enable */ __HAL_RCC_USART1_CLK_ENABLE();   __HAL_RCC_GPIOA_CLK_ENABLE(); /**USART1 GPIO Configuration PA9 ------> USART1_TX PA10 ------> USART1_RX */ GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10; GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_I

 Hey,I am trying to include X-CUBE-IRREMOTE for stm32g030f6p6 but it doesnt show up in software packs in cubeMXif i try to manually install it it gives an error of invalid packet

My Firmware Package name and version: STM32Cube FW_F1 v1.8.4Bug detail: After code generates, the code order is:In this order, receiving message of the usart will get some bugs, eg: only can receive the last byte...I let `the MX_DMA_Init();` become the first one solve the problem, but when I genearted code next time, this order will appear again...

In the wiki ( https://wiki.st.com/stm32mcu/wiki/Connectivity:STM32WB_FUS ), it is said:Interfaces that can be used to communicate with FUS are:System bootloader (USB DFU and USART): provides ready-to-use commandsSWD (FUS_Opeartor): provided by ST inside the STM32CubeProgrammer tool and offers ready-to-use commands.Userapplication on CM4: can be developed by the user based on STM32WB CubeFW examples (and in the future using Open Bootloader integrating FUS_Operator)Does the example that shows how to access FUS from user application actually exist ? I did not see any such example in STM32Cube_FW_WB_V1.13.0. or its patches (up to 1.13.3).I want to find a way to update the wireless stack in the field (no SWD, USB or UART, only our own bootloader with access to a user-accessible SD card).Best,Nicolas

Hi there, I have been using STM32G474, but if I look into the HAL driver folder structure I cannot find the files for LL-Drivers. I want to use LL functions in my code. Looking forward to your quick suggestions.BRs,Waled2G474RE, the documentation says that it supports

Hello. I would like to print certain messages to UART only in DEBUG mode. These prints will not be necessary in release mode.I have tried the following:#ifdef DEBUG printf("hello from debug \n"); #endifAnd then I have built the project for both release and debug but the message is printed in both cases. How can I only get message to print in debug mode and not in release mode?

..

Hello,In order to reduce the programming tima at the production line for our SPC58 could you please help with the following points?What is the FLASH memory state at the MCU delivery?What are the recoomendations to reduce the primary programming during production?Can BAF be used for this? Is there any SW for using BAF for primary programming?How can the figures mentioned in DocID029264 Rev 2, June 2016 for FLASH programming time be reached? - see an image below: Thank you in advance,Veniamin

..

I'am working on automotive project that the client need a validation plan for automotive device using SPC584B MCUI have did a search on st.com site to find somthing about CAN/UDS bootloader but i did'nt find the appropriate document for my need.any sugesstion , links , tools , document , about bootloader validation and the ecosysteme for this task?

I'am working on automotive project that the client need a validation plan for automotive device using SPC584B MCUI have did a search on st.com site to find somthing about CAN/UDS bootloader but i did'nt find the appropriate document for my need.any sugesstion , links , tools , document , about bootloader validation and the ecosysteme for this task?

I want to make a Filesystem with FileX and use the usbx device storage class to get access to the files. I successfully created a FileX filesystem on ram. I found the examples Ux_Device_MSC, this uses the sd card for the file system.In ux_device_msc.c i have to implement the Status Read and Write commands comming from usb to acces my filesystem. /* Format the NOR flash as FAT */ status = fx_media_format(&sram_disk, fx_stm32_sram_driver, // Driver entry (VOID*)LX_SRAM_DRIVER_ID, // Device info pointer (UCHAR*)media_memory, // Media buffer pointer sizeof(media_memory), // Media buffer size "SRAM DISK", // Volume Name 1, // Number of FATs 32, // Directory Entries 0, // Hidden sectors FX_SRAM_DISK_SIZE/512, // Total sectors 512, // Sector size 8, // Sectors per cluster 1, // Heads 1); // Sectors per trackCurrently im using this for read and write, but windows tells me i have t

..