Solved

Hello Support Team,Currently, I am working with FreeRTOS and using STM32cube IDE.I have created two tasks in my FreeRTOS-based application.I need to require the below data using STM32 cube IDE when both tasks are in a running state.Both tasks are running in CORE-M7.i)   CPU utilization(for particular CORE-M7)ii) RAM Usageiii)FLASH usageEx. In Linux, we easily view the particular process CPU usage and memory.  Could we do the same thing for a particular CORE-M7 in STM32 cube IDE?Let me know how to achieve this in STM32Cube IDE for FreeRTOS.Or, Required any plugins for this give all steps for how to add plugins and use them.Hardware and Software Details:1) Hardware :  - STM32H745 Discovery board.2) Software :  - STM32cube IDE Version: 1.8.0 - OS - Windows OS(Windows 10)Thanks In Advance..

Hello,How can I rename the project-name in STM32CubeIDE ?If I right click on the project(name) and choose rename I get the following error, see attached screenshot.Thank you 

Hello, I have an IPM10F and try to switch on the gate, so I can measure a current on the Output U. My Problem is I measure nothing.I put a constant 3.3 Voltage to the Gate-Pin A-High. On the Output (U) I connect a resistance to override the LOW-Switch. After that I tried to measure with a multimeter. I linked one end to the resistance and the other to the ground, like normal. Thank you

Hi ExpertsI used NFC Tap App to transmit data(use FTM write message cmd), transmit 10 byteAs my analysis below the last 4 byte should be the CRC(4 byte)，I think it's use CRC32 method, but I can't calculate the result as same as the App Results by using on-line CRC calculatorCould you please verify this for me? thank you very much!

Is there a rule where to put code into main.c so that it stays there permanently? It happended to me now a couple of times that I added an interrupt callback function which suddenly disappeared. Are there areas in main.c where to safely put those?

Hello,I am working on nucleo-h745ziq board.Interface the usb as custome HId. I try to install the USB HID Demonstrator but it throws error .There is another terminal so I can use ? Please help me

helloWe are using STM32MP157A-dk1 evaluation board. To this we are writing bare metal code in SEGGER Embedded Studio.Actually, We have enabled group and set enable registers for respected SGI and PPI interrupts in GICC and GICD registers. By this we are able to generate SGI and PPI interrupts for cortex A_0 but unable to generate for cortex A_1. what might be the issue ?regards srikanth

I need to transmit data over usb with minimum 1 Mb/s from device to host, I configured my mcu (stm32h732zg) as an audio device to get a large packet transfer.the function that transfer the data USBD_AUDIO_DataIn is empty. and USBD_CtlSendData i'm using cause the usb descriptor request failed.

Hello, I found the altium files including layout for X-Nucleo-NFC08A1? I saw the Altium files for the X-Nucleo-NFC06 but nothing for the newer board. On the web there are the gerber files posted but they're for the X-Nucleo-Out08A1, not the same board. Having the raw Altium files will make it much easier to determine exact location of components.Thanks

I want to make Websocket Client in STM32CUBEIDE and I am using STM32f407 Discovery Board, I have completed the Program with Ethernet(MII, DP83848) with LWP(DHCP enabled) along with FREERTOS. So kindly help me in giving support for the same....

I have the STM32H745I-DISCO board for tests.I want to achieve a simple thing: play 1KHz sine wave over the speaker output of the board.As I researched the subject I found in the documentation:"Two external speakers can be connected to WM8994ECS/R via JP5 for the rightspeaker and JP2 for the left speaker"Good.Then, the WM8994 chip can be accessed via SAI / I2S.I've seen https://github.com/STMicroelectronics/STM32CubeH7/tree/master/Projects/STM32H745I-DISCO/Examples/SAI/SAI_AudioPlaybackI don't know how to run it. The example requires IDEs I don't have and I'm not familiar with. However, looking at the sources, I see it uses PDM2PCM Middleware.I just tried to add it to my STM32CubeIDE project. Of course, the CubeIDE failed to generate the configuration dumping mx.scratch file.Looking at the file I figured out I need to add following include paths:../../../Middlewares/ST/STM32_Audio/Addons/PDM/Inc../../../CM7/PDM2PCM/AppAnd the link to CM7\PDM2PCM\App and Middlewares\ST\STM32_Audio direct

STM32G473CCT uses the HAL library for writing flash pages.i have constructed some code to use the last FLASH page as NV memory.bool eeprom_write8(uint16_t address, uint8_t data) { return eeprom_write(address, &data, 1); }   bool eeprom_write(uint16_t address, uint8_t *pdata, uint16_t size) { static uint8_t ARRAY_ALLIGN(PageData,FLASH_PG_SIZE);   __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PGSERR); __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_SIZERR); __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PGAERR); __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_PROGERR); __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_FASTERR); flash_status status = FLASH_OK;   if((address+size) > EEPROM_SIZE){ return false; }   if(eeprom_page_data_changed(address,pdata,size)){ // data changed -> // store page content in ram and do a page clear eeprom_storepage_and_erase(PageData); // update the data with the new data for(uint16_t n=0;n<size;n++){ PageData[address+n]=*pdata; pdata++; } // write the updated

This is my first STM32 project and I am using an STM32F030C6T as a MODBUS slave device. I used the STM32CubeMX V6.6.1 to create a project template and STM32CubeIDE Version: 1.10.1 Build: 12716_20220707_0928 (UTC), along with an STlink interface.When I build the MX project using HAL driver under project settings/advanced the project builds correctly but when I download into the target device it crashes as soon as it tries to initialise the USART and other devices. If I comment those drivers out so only the GPIO is initialised I can get the GPIO to run for a very short time before in triggers the HardFault interrupt.If I rebuild the project and change to using the LL driver interface, the code builds and downloads and runs without issues. I can then add my 5 lines of code for a blinky light.Seems to be an issue with the HAL setup or my environment, any suggestions welcome.Footprint for the LL interface is  HAL footprint 

I found a strange mismatch in the reference manual for the OTP memory size:Accordingly to the manual page 78 (https://www.st.com/resource/en/reference_manual/rm0385-stm32f75xxx-and-stm32f74xxx-advanced-armbased-32bit-mcus-stmicroelectronics.pdf) the start-address of the OTP memory begins at `0x1FF0 F000` and ends at address: `0x1FF0 F41F` (in AXIM mode) and is declared as a memory area with the size of 1024 bytes.But if I calculate `0x1FF0F41F - 0x1FF0F000 + 1` I get a total of 1056 bytes OTP memory?!Is this a typo in the manual or is my calculation wrong?

I bought STM32F0Discovery. However, I cannot write the program with STM32CubeIDE. It says that ST-Link firmware update is required. When I try to update it says ST-Lijnk is not in DFU mode.Can anyone tell me how to put STM32F0Discovery into DFU mode?

Hello,I created a new project in STM32CubeIDE for my STM32MP157A by using STM32CubeMX. In it I enabled UART and FreeRTOS on CMSIS-RTOSv2 and that's all. I use the auto generated code.Then I wanted to use TraceAlyzer on top of FreeRTOS however, upon including#include "trcRecorder.h"In the FreeRTOSConfig.h I got a strange error:/Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c:154: multiple definition of `SysTick_Handler'; ./Core/Src/stm32mp1xx_it.o:   ./CM4/Core/Src/stm32mp1xx_it.c:160: first defined hereThe SysTick_Handler is defined in both files, here are the implementations if it may help:in cmsis_os2.c :/* SysTick handler implementation that also clears overflow flag. */ void SysTick_Handler (void) { /* Clear overflow flag */ SysTick->CTRL;   if (xTaskGetSchedulerState() != taskSCHEDULER_NOT_STARTED) { /* Call tick handler */ xPortSysTickHandler(); } } #endif /* SysTick */In stm32mp1xx_it.c :/** * @brief This function handles System tick timer

How can I connect external ram to stm32h743vit6? I need at least 2 MB of external memory for the display (800x480 16 bit color). SDRAM unfortunately this microcontroller does not support

We've been using the LSM6DS3 for several years, and are considering a switch to the LSM6DSM. It appears they are pin-compatible, and a superficial look at the register descriptions indicates they could be software-compatible as well, i.e. I could swap the ...DSM onto the same PCB and it may work out of the box.Sadly, my SMT reworking skills aren't yet up to the task of swapping the ICs on a board, and I'd prefer not to spend half a day comparing the datasheets line by line, so I'm hoping somebody can answer the question off the top of their head: can I swap out the LSM6DSM on this board and expect it to work without changing my code at all? I'm not doing anything fancy with it, just setting ODRs, ranges, and using the FIFO.EDIT: I *did* manage to rework a board, and I2C communication appears to be working, but the data isn't yet flowing. It's possible that the INT line somehow isn't connected while the rest of them are.

How do i find an extensive example for read/write value in flash of STM32H7, for store of data to keep after powerloss or reboot? Thanks

Hi! I'm searching a way to exit from the builtin bootloader after having successfully programmed my flash from USB. Is it possible to jump to my program in flash if I continue to hold the boot0 pin always high? I have done some attempts using STM32_Programmer_CLI.exe specifying the start address (option -s from command line) to my ResetHandler function which is in flash at address 0x8000970. It seems that this doesn't work and it needs to switch boot0 pin at a low level to make it works.Just to explain my setup: I'm using the STM32_Programmer_CLI.exe program as following:STM32_Programmer_CLI.exe -c port=USB1 -w myprog.bin 0x8000000 -s 0x8000970Do you have any suggest? Thank you!

..

Hello​I developed prototype of wearable device using STM32WBMMG, and planning to acquire FCC certification.​​STM32WB5MMG already has FCC ID; YCP-STM32WB5M001; however, it is the certification of the chip itself.​When mounted any kind of devices(PCBs etc.), another FCC certification for device is required.​At this point, for device certification, the Bluetooth antenna should be able to connect or disconnect.However, STM32WB5MMG is integrated with MCU and Bluetooth module with antena.​Is there a way to connect or disconnect only the antenna?​Thanks.​​​

I'm using the latest API version (1.2.8) available from the VL53L4CX product page.In my project I have implemented an interface to set configurations or run calibrations.I am also using this driver for both the VL53L4CD and VL53L4CX, since the driver seems to be universal for all VL53LX parts. Correct me if I'm wrong.(Problem 1 )I noticed the function VL53LX_PerformOffsetPerVcselCalibration(~) would hang seemingly at random calls.Below is the block of code with the issue and a potential fix. After I changed it, I've had no issues running it.while ((Status == VL53LX_ERROR_NONE) && (inloopcount < Max) && (inloopcount < OverMax)) {   Status = VL53LX_WaitMeasurementDataReady(Dev);   if (Status == VL53LX_ERROR_NONE)   Status = VL53LX_GetMultiRangingData(Dev, &RangingMeasurementData);   pRange = &(RangingMeasurementData.RangeData[0]);   goodmeas = (pRange->RangeStatus == VL53LX_RANGESTATUS_RANGE_VALID);   ics = pdev->ll_state.

The product's part number is "VNL5030JTR-E". They had different levels of ecopack. One is ECOPACK 1, another is ECOPACK 2. I found the website shows the product is Ecopack1 in May 25, 2021. But now the website shows the product is Ecopack2. Coul you provide the product change notification ?

Hello @ST_community,I am Trying to program STM32-H7A3ZI-Q Nucleo board.I couldn't debug the board attached the images for reference. Also Attached the log file for reference. Please let me know how to debug.Thanks,