Solved

..

..

I am using a stm32g0b1ret with stm32cubemx package 1.6.1 .The symptoms are:On deletion of pages I receive a signal 0 in the debugger, but the pages do get erased eventually. (I use HAL_FLASHEx_Erase)On the first flash write I get an error with goes to hardfault - because the Flag CFGBSY is set. (I use HAL_FLASH_Program, with Doubleword).A reset cures this, and then the writing happens without a further problem.On the next erase the problem is repeated.Questions: I do not know, if this solves my problem, but it looks like there is an inconsistency between the ref man RM0444 and the cube-mx firmware/sample project.CubeMX: Erasing pages in bank 2 assumes and asserts page number start from 0 to 127 for both banks and the choice of bank is done solely by the BKER bit.Reference manual rev 5, page 71/page102 -> this looks like page numbers for bank 2 start at 256 (with a gap from last page 127 of bank1). I have tried both ways, the pages get deleted in both cases, but also the error seems

Hello all, The model::tick() and screen::handleTickEvent(), which is calling first?How do I query the tickEvent() calling sequence (model / screen / widget) ??

Hello,I wanted to try the SBSFU topic 6 step by step youtube video, i accidentally flash the Userapp.bin with the RDP level 1, (and also with Write protection enable in bank1).I try to change the RDP level back to 0, and also disable the Write protection on bank1, however the mass erase option had not been successful, can you advise if such revert is possible? it means that those protected area was not able to be erase.(0x8000000), or the board had become unusable?

..

I am a 10yr Arduino IDE programmer and I have a cheap ST-Link V2 (Canaduino). M5Stack provides a copy of the firmware and I would like to experiment with making it a stand alone MCU that could read inputs and respond with outputs. I would like to do this in Arduino V2 IDE as I am very familiar with this.How feasible is this?!-Terry

..

Hi Guys,I have problems reading. I have followed the STM32WB Workshop on stm32wb (using mx version 5.4.0). Now i'm trying to read but all examples seem to only use notifying and writing.I have the following char created and added some default value.aci_gatt_add_char(SvcHandle, UUID_TYPE_128, &uuid16, 1, CHAR_PROP_READ | CHAR_PROP_WRITE_WITHOUT_RESP, ATTR_PERMISSION_NONE, GATT_NOTIFY_ATTRIBUTE_WRITE | GATT_NOTIFY_READ_REQ_AND_WAIT_FOR_APPL_RESP, 10, 0, &(AlarmThresholdHandle));   uint8_t pData[1] = {59}; aci_gatt_update_char_value(SvcHandle, AlarmThresholdHandle + 1, 0, /* charValOffset */ 1, /* charValueLen */ pData);    Within server app handler it enters this case when im reading, and found the right handler. This is the part where i get lost, what to do next? I implemented the following but that does not work.case EVT_BLUE_GATT_READ_PERMIT_REQ: { aci_gatt_read_permit_req_event_rp0* attributeToRead; attributeToRead = (aci_gatt_read_

Installed the X-CUBE-AZRTOS-L4 package with the CubeMX "Install software packages" function. Looks like it is installed.Starting a new Project with an STM32L4 device does not show the Azure RTOS Middleware options. Bug or what I am doing wrong?!

I am using UART to transmit and receive data. for transmitting I am using polling method function HAL_UART_Transmit(&hart1, buf, 8,1000) and for receiving i am using HAL_UART_Receive_IT(&hart, Rx_buf,8); receiving is working fine but after transmitting any data the receive callback is getting fired and after that the receiving interrupts are not getting fired even though I am transmitting data from another device.

I have STM32G071 MCU to control a USB Type C hub and I want to use VBUS Powered sink in the application. I have connected Dead Battery pins to their respected CCx pins. It supposed to act as a sink when there is no power but when I connect the type c port to a device, it does not act as a sink and connected device does not give any power. I have activated the Dead Battery signals in STM32CubeIDE but it does not work. Also I have tried activating signals by configuring SYSCFG register but it did not work either. What should I do to make it work?

Hello Everyone,I currently trying to implement a FFT by using the optimized functions from CMSIS library on a L5 MCU. The fact is that the M33 family seems not to be supported then I was wondering whether there's some kind of workaround in order to make it work properly.Any suggestions could be very helpful!Thanks in advance

Hello ST community,I am developing an application based on B-U585I-IOT02A. In this I am using the MX25LM51245G which is on board NOR flash connected via OCTOSPI. The functionality is to save and retrieve a .bin file from the NOR flash. Please let me know how can we achieve the same.Regards

We're working on custom data transfer between Android and our custom device with NFC. As Android no longer support peer to peer, we're investigate the best way to do it. ST provides ST25FTM library to do this with the ST25DV-I2C tag, but it is too slow ~25kbps. We want something faster around 115kps.Is there anything library similar to ST25FTM and allows ST25R3916 to perform data transfer? (Either in reader or card emulation mode). If not, which direction we can take to perform data transfer with Android low level API. Thanks

I was running and debugging a part of my application on a stm32F207zg microcontroller.Microcontroller is on a custom PCB that is in validation process.This part of application has to set or clear 16 gpios configured as output.If they are initialized to be "on", outputs start with "on" state correctly. So, the whole output port can be written with "high logic level". If LEDs are connected on there, they turn on.In other part of my code that I'm using to play with output operations for testing purposes, a function is writing high level state at whole GPIO output port (x16 pins) once again. But the weird behavior comes here: pin4, pin 5 and pin16 don't set their values.I was debugging HAL_GPIO_WritePin function. Remembering how does HAL set the value I share the code from HAL_GPIO lib:* @param GPIOx where x can be (A..I) to select the GPIO peripheral for all STM32F2XX devices   * @param GPIO_Pin specifies the port bit to be written.   * This parameter can be one of GPIO_PIN_x

Hello,I have a ST25RU3993 RFID reader, and I started with it. For starting I download and use the Software Development Kit for ST25RU3993 based evaluation boards for testing my reader. However I have a problem. My reader has a firmware that does not match with the SDK. The SDK requires update the firmware. When I process to update the firmware SDK throws an error, that say that the device is not recognize. What could be the problem? Or how could I make my reader be recognized? Thank you and regards

..

NFC Tag app邮箱功能怎么没有�??应，NFC连接上之�?�打开邮箱�?置密�?之�?�下�?�四个按钮都没有�??应Post Edited to add translation to English:Why does the mailbox function of the NFC Tag app not respond? After the NFC connection is connected, the mailbox is opened and the password is configured. After the four buttons below do not respond

Hello ST community,I use a STM32F3348 DISCO board (STM32F334C8Tx MCU) and I would like to realize a PWM with a period of 4µs (250 000 Hz) and a pulse width of 13,9ns. I tried first with the TIM1 and then with the HRTIM but in both cases I can't reduce the pulse width below 50ns.However the HRTIM has a resolution of 6.95ns so normally it is possible. But even taking the examples provided for this timer, it’s as if the card was limited. Can you give me some guidance on what I might have forgotten?

Hi. I have a P-NUCLEO-IOM01M1 and it seems to have fallen into disrepair. It was re-flashed via STM32CubeProgrammer. Could you help, surely there is a solution to this problem. Thank you.

Hello,I am using the STM32MP157F-DK2 and recently went through a textbook rebuild of the Linux kernel, the modules and the gcnano driver (for GL support). All is well and yet, I see only one of the two CPUS. dmesg tells me the following:[   0.000000] ------------[ cut here ]------------[   0.000000] WARNING: CPU: 0 PID: 0 at arch/arm/kernel/devtree.c:148 arm_dt_init_cpu_maps+0x168/0x250[   0.000000] DT /cpu 2 nodes greater than max cores 1, capping them[   0.000000] Modules linked in:[   0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.15.67 #1[   0.000000] Hardware name: STM32 (Device Tree Support)[   0.000000] [<c010e8ec>] (unwind_backtrace) from [<c010c158>] (show_stack+0x10/0x14)[   0.000000] [<c010c158>] (show_stack) from [<c0122404>] (__warn+0xec/0x148)[   0.000000] [<c0122404>] (__warn) from [<c0c33034>] (wa

I want to switch from FreeRTOS to Azure RTOS ThreadX. In FreeRTOS there is the function xQueueSendToBackFromISR() - It is used to write data to the queue from an interrupt service routine. FreeRTOS interrupt provides an interrupt safe version of queue API to read and write data from queues using ISR. https://www.freertos.org/xQueueSendToBackFromISR.html And I am looking for the equivalent function in Azure RTOS ThreadX.I looked up the documentation on Microsoft website and went through the functions but it seems that there is no such function in Azure RTOS ThreadX? https://learn.microsoft.com/en-us/azure/rtos/threadx/chapter4

I have used CubeMX to generate an application structure for the STM32F746 DISCO board.When trying to run the most basic application, during the initialisation, TIM6 is set to be the HAL tick source, when it is enabled, it immediately jumps to its interrupt, and then gets repeated called, stopping any further progress.This is also happening with the TouchGFX code taken from the example library.

The program can't find any ST-Link connections:But I can use the STM32CubeProgrammer to flash my board via ST-Link/V2 SWD.Could you please help me to figure out what is missing?I need to write a program to flash the board and I can't even see it! Please help.Thank you.