Solved

Posted on May 12, 2017 at 11:02I've noticed this behaviour in Atollic TrueStudio 7.0.1 and 7.1.2, using the ST-Link V2 debugger (several variants, including the regular ST-Link V2 and the ISOL version). When I place a breakpoint in the code, the execution stops at the breakpoint, I can inspect variables and otherwise interact with the device under test, but the device continues to run.The debugger is clearly in 'Suspended' mode, but the target is running : status LEDs are still blinking and it's responding to its environment. When I try to step through the code, it jumps to a seemingly random location instead of going to the next line. This is a recent bug, doesn't happen all the time, and a colleague of mine has also experienced it recently.Running our own code on a STM32L151RB. Any ideas?Thanks in advance.#stm32l1 #st-link/v2 #debugging #atollic #truestudio

Posted on May 11, 2017 at 22:51I am using the STM32L437 part and I run into some confusion with SysTick. I set up the SysTick to run at 1ms with timer 5 as Timebase source (for comparison). As a sanity check, I also set up timers 3, 4, 6 and 7 independently at 1ms as well, thinking they would all match up pretty closely but the results for SysTick and timer 5 are a bit different from the other 4 timers. In this test code I only use one clock source at a time (either internal OR external, no mixing... when using internal clock source the difference is even more pronounced). As you can see here the SysTick and timer 5 show 2669 seconds elapsed, but the other 4 regular timers show 2612 seconds, a difference of 57 seconds. Does SysTick run on a different clock than the other timers? Is there anything special about SysTick compared to other timers that I am not aware of. Thanks!ED

Posted on May 11, 2017 at 16:04Suppose there's a table with two columns: column A has the destination address and column B has the value I want to write to the destination. (Destination addresses in column A are NOT contiguous) Is there any way to direct the DMA to read the destination from column A and conduct the transfer of Column B without CPU intervention? Curious about the F4 / F7 but would welcome any input on any other Cortex cores if available.Thanks!#memory #stm-32f7 #f7 #dma

Posted on May 09, 2017 at 11:18   Dear community, I am using STM32F746 Discovery and the IDE is Keil C. I have a problem with Keil C Compiler.   My project have 2 parts:       Part 1. Get pictures (BMP) from SD Card and print to LCD screen. It is working well.      Part 2. Measure analog signal by ADC, get and save data from/to RTC , External Flash, then print the data to LCD screen. It is working well too.   However, the problem is just only one part is working without the other part in my code. When i add both in my code, it is not work (just only SD Card is not work). Example:A. Only part 1:int main(void){       System_Config();                           // Configure the System       SD_BMP_LCD(); &nbs

Posted on May 10, 2017 at 11:12Hii need to set up a demo for CAN protocol. I need to recieve some CAN cmds and toggle a pin.Which eval board should I get?Where would I find example projects for a can receiver?Thx

Posted on May 09, 2017 at 12:20Hello fellow developers,I have an stm32f4 board connected to PC through a USB link. Basically, the board is linked through an SPI link to several sensors. It gathers data from the sensors, filters and processes it before it sends it to the PC through the USB link for further processing and to display the results. I am building the USB link on top of the ST cube USB library and all works well.I have lately been adding further data to the processing algorithm. I am using an array of 8 elements to average the sensors data. I have two sensors connected that I need to do this to. When I add the averaging algorithm to one sensor, everything works great and no problems occur what so  ever. When I add the averaging to the second sensor I start to get a weird error. Basically, When I restart the PC, things work for some minutes before the USB communication stalls. To make the system run again I have to unplug and plug the USB cable. At this point, everything

Posted on April 18, 2017 at 22:04My understanding of the UID is it's plopped into the device by ST and not touchable write-wise (read only) .Makes it good for use in SERIAL number application like USB descriptor serial number string.For the STM32L476 which address is correct for the UID register location ? 1FFF7A10 or 1FFF7590?And is the EVAL CDC demo fouled for this?-------------------------------------------------------------------------------------------------STM32L476 manual RM0351  (REV 5 March 2017) says49.1 Unique device ID register (96 bits)The unique device identifier is ideally suited:• for use as serial numbers (for example USB string serial numbers or other endapplications)• for use as part of the security keys in order to increase the security of code in Flashmemory while using and combining this unique ID with software cryptographicprimitives and protocols before programming the internal Flash memory• to activate secure boot processes, etc.The 96-bit unique device i

Posted on May 05, 2017 at 18:44Hi,I'm trying to connect a TTL-232R USB-UART Converter to an STM32F3DISCOVERY board. I've connected the TX/RX wires on the TTL-232R to PB10/PB11 on the STM32F3DISCOVERY board. I have the board connected to my laptop over USB.Do I need to connect the 5V/GND wires on the TTL-232R? Or are these signals already provided by USB?Any help would be much appreciated.Cheers,Tony#uart #stm32f3-discovery

Posted on April 26, 2017 at 07:14Hello,I am working with the STM32L476G-Discovery board. I am testing the examples applications and I have found an error in the demonstration application regarding to the soundmeter feature.* With the *.bin file provided in the Binary folder the application works normally. I mean, that you can see in the Display how it changes the sound intensity in dB when it is louder or not.* but, with the IAR source code project, when you program the demonstration application in the STM32L476G-Discovery board, the soundmeter feature doesn't function anymore, it shows a constant value of 120dB in the Display of the board.I think again, somebody change something in the code and he forgot to test it. Typical, very typical.Please, check this error as soon as possible and provide a change in the software to solve this problem.Regards,Daniel

Posted on May 03, 2016 at 17:10Hello communityhere they are my 5 cent of opinion about the - otherwise great - Cube MX.I ee that, whenever I regenerate a project for whatever reason (changing clock scheme, using DMA for USART instead of polling etc.), if I keep the same project name the Cube re-generate the HAL coden of the select peripherals (OK), keep the user code inside the 'user-code begin / end' keyword of the source files (also OK) but- a - recreate a new project file everytime (do not like)- b - delete the user files under the directory <proj_name>/src and inc (do not like)My project is under revision control so -b- is not too much annoying but -a- is: I cannot restore the old project file without loosing any new option introduced by the lastest Cube MX runPlease comment or advice in case I am doing something wrong or using a bad methodologythanks

Posted on May 05, 2017 at 16:24Hello All,I am using SPC560B54L5 board along with SPC5studio 5.2.1 and UDE 4.2In my application I am trying to receive 256 bytes of data/packet and sending 30 bytes(max.) of response to the sender. The application starts working initially, but after sometime(most of the time after 274 packets)  it blocks somewhere. The status in UDE shows ''core running'' but failing to send or receive data through UART.If I try to break the execution explicitly in UDE, UDE prompts to select the source file''reent.c''.No other interrupts except UART and PIT(PIT0 for syswaitmilliseconds()) , are in my application.Prompting for reent.c:Kindly provide your valuable suggestion to resolve the issue.

Posted on May 08, 2017 at 17:45I am not having any luck on the st.com site finding source for stm32f4x7_eth.c. Could someone please point me in the right direction?Thanks,John

Posted on May 07, 2017 at 23:19Hello,I have encountered problem with printf function. I am using CycloneTCP stack, where %hhu identifiers were used and workeg good. I tried to port demo applications to CubeMX etc and I got eferything working well besides printf with %hhu identifiers.I have created new project with only this function in it, here is the part of code:size = sprintf(buffer, '%u, %hu, %hhu\n', 123, 123, 123); HAL_UART_Transmit_IT(&huart3, buffer, size);What I get is:123, 123, huDoing the same in original demos of stack mentioned above give good results. What I tried is to change language standard to C11 but it didn't make any change. Have you met such a problem?Regards,Pawel#printf #stdio

Posted on January 04, 2017 at 15:32Hi, Looking to download X-CUBE Cryptolib firmware library software expansion for STM32CubeMX. But after filling up the form and clicking on 'Submit Request', nothing happens. No email with link to download or any further updates on Form.Can you help please? Is there any other way to download this library?Regards.

Posted on May 07, 2017 at 19:43this is the LIS3DSH  accelerometer on stm32f4discovery board0.12 mg/digit sensitivity it has how to calculate exact output with respect to unit of gis there any tutorial or documentation that  explain stuff.##lis3dsh #mems #accelerometer

Posted on May 02, 2017 at 10:53hi, i am new to community.....i have a stm32f4 discovery board with sym32f407cg microcontroller i tried to test spi communucation of the microcontroller with onboard accelerometerbut there is one or more problem that i can not handethe problem is whatever i write on data register of spi1 , the register only shows 0xff when i read it with the help of pointerhow can i solve this problemthats what i did as settings of spi1..spi_cr1 |= 0x30; // select speed spi_cr1 |= 0x03; // select cpha and cpol spi_cr1 |= 0x00; // select dff spi_cr1 |= 0x00; // select msbfirstspi_cr2 |= 0x10; // select frf spi_cr2 |= 0x04; // set ssoe spi_cr1 |= 0x04; // set mstr spi_cr1 |= 0x40; // enable spi##discovery ##spi #stm32

Posted on September 15, 2016 at 01:01Hi, the topic probably explains it all. When creating a new project with CubeMX, there's usually a long list of TODOs showing up under tasks (using Atollic) which makes it rather difficult to set up my own tasks. Example in csmis_armcc_V6.h: /* ToDo:  ARMCC_V6: check if __builtin_arm_rbit is supported */ Would it be asked too much to tidy up any leftover //TODO comments from any generated source files before release? Thanks!

Posted on May 04, 2017 at 15:22Hi there, is there anybody with STM32F7XX and is able to read bigger file (larger than 30MBytes) from SD card until the end ? without DMA ?i'm asking because i tried more types of cards, and i tried to setup clk div for SDIO to 400kHz and i don't have any success :(i always get error RXOVERR in SDMMC_STA after couple MBytes (2MB-3MB)i need just confirmation that it's possible ...thanks for all replies ...Kind regards

Posted on May 03, 2017 at 01:36 When compiling projects using standard HAL libraries, I often get a dozen or so warnings about unused parameters in library functions. Would it be possible to tell your programmers to please add '__attribute__((unused))' in front of all unused parameters or unused variables in general? Right now my only solution is to completely disable all warnings for the 'Middlewares' and 'Drivers' folders which is not really helpful. Examples: usbd_desc.c: uint8_t * USBD_HS_ManufacturerStrDescriptor(__attribute__((unused)) USBD_SpeedTypeDef speed , uint16_t *length) { USBD_GetString ((uint8_t *)USBD_MANUFACTURER_STRING, USBD_StrDesc, length); return USBD_StrDesc; }�?�?�?�?�? uint8_t * USBD_HS_LangIDStrDescriptor( __attribute__((unused)) USBD_SpeedTypeDef speed , uint16_t *length) { *length = sizeof(USBD_LangIDDesc); return USBD_LangIDDesc; }�?�?�?�?�? Compiling a sample project with some extra warning flags enabled should give a very quick & e

Posted on March 24, 2017 at 13:42CubeMX 4.20 pin initialization problem . Hi, after I installed version 4.20 (no problem on previous version), TIM1_PWM_CH1 on pin A8 din't work (MCU - stm32f030r8t6, IDE - KEIL 5.20 ).I found that in the file stm32f0xx_hal_msp.c in HAL_TIM_MspPostInit function, not generated string: GPIO_InitStruct.Alternate = GPIO_AF2_TIM1; 

Posted on May 02, 2017 at 10:54 I am using a STM32L476VG (100 pin package, VREF+ not bonded to VDDA) for a mixed signal design. I planed to use the VREF+ as a 2.048V reference output. Currently there is no load on the VREF+ pin. Unfortunately I always get a HAL_TIMEOUT while waiting for the VRR bit in the VREFBUF CSR register: HAL_SYSCFG_VREFBUF_VoltageScalingConfig(SYSCFG_VREFBUF_VOLTAGE_SCALE0); HAL_SYSCFG_VREFBUF_HighImpedanceConfig(SYSCFG_VREFBUF_HIGH_IMPEDANCE_DISABLE); if (HAL_SYSCFG_EnableVREFBUF() != HAL_OK) { Error_Handler(ENVREFO_ERROR); }�?�?�?�?�?�? Also no voltage output is measureable at the VREF+ pin... Do I miss something here? I tried to change the order or manually set the registers (without time-out) but no output at all. Thank you for your help!! Best regards, Merlin #analog #vrefbuf #reference #vref+ #csr

Posted on May 03, 2017 at 17:12As the tittle ! Thanks for help!!!

Posted on May 02, 2017 at 12:07HiI am trying to read an adc value from a potentiometer with the following code:         uint32_t readADCServo()         {         uint32_t adcValue, adcValueDegrees;          HAL_ADC_Start(&hadc1);          if (HAL_ADC_PollForConversion(&hadc1, 1)!=HAL_OK)          {           }          while ((HAL_ADC_GetState(&hadc1) & HAL_ADC_STATE_REG_EOC ) == HAL_ADC_STATE_REG_EOC)          {          adcValue = HAL_ADC_GetValue(&hadc1);          

Posted on May 02, 2017 at 23:38NFS course in Udemy website is locked as a private course and requires invitation request to be accepted.I don't know if it is really required to lock a course when creating a user account needs approval, but if it's an accident I ask someone in charge to unlock and/or approve this request too.Thanks in advance :]#udemy #courses

Posted on May 01, 2017 at 20:20I'm running into a Hard Fault when sending 9 bytes from a PC to a STM32F103C8T6 using USB CDC code generated by Cube 4.20.1, FW F1 V1.4.0.  I can send 8 bytes to the microcontroller without issue, but once I try 9 bytes, the micro runs into a Hard Fault.The project is generated in CubeMX, using System Workbench IDE, and running on a custom board.  The only changes to the generated code is a section that pulls down D+ and waits 500 ms before calling MX_USB_DEVICE_Init().  This allows the PC to de-numerate and renumerate the device.I'm running RealTerm on my Windows 10 PC, under the 'Send' tab, using the data '123456789', and then 'Send ASCII'.  At this point, the microcontrolller goes to a Hard Fault.  (See attached image for stack trace)  If I send '12345678' instead, everything runs fine.  I'm not sure how to debug this, so any advice is appreciated.  Thank you!#cdc #usb-cdc #usb #hard-fault