Solved

Computer in Linux.I already have stcubemx 6.0.1 installedI install the st-stm32cubeide_1.4.0_7511_20200720_0928_amd64.sh, installation OK. The program indicates that there is version 1.4.2, I start the software update and it gives me the following errors:How can I solve the problem and upgrade to version 1.4.2?Best regards

I'm configuring an STM32G474VEH and I right clicked on pin PA3 and I get the attached popup dialog.The datasheet has OPAMP1_VINM / OPAMP1_VINP / OPAMP5_VINM.How do these each of these three items map to the entries in the list below?

Hello, I have a problem with a typedef struct.I made a typedef struct :typedef struct BMP280_HandleTypeDef{  uint16_t dig_T1;  int16_t dig_T2;  int16_t dig_T3;} BMP280_HandleTypeDef ;In my function I declare the instance of it :void myfunction{BMP280_HandleTypeDef dev;...MyFunction2(&dev); // I want to pass the pointer of the struct to an other function }// Prototype of MyFunction2void MyFunction2 ( BMP280_HandleTypeDef *dev);The compiler gives me this error:error: unknown type name 'BMP280_HandleTypeDef'; did you mean 'I2C_HandleTypeDef'?I use STM32CubeIde. Thanks in advance for your help .Pascal

I start a new project with the following steps:I create a new STM32 ProjectI select STM32L4P5G-DK from the Board Selector MenuI initialize the board with it's default configurationI have successfully configured the I2C4 and USART2 peripherals on the STMod+ Fan-Out Expansion Board, and they are working as expected.However, I am having difficulty when I attempt to enable USART3 (available on the expansion board) for use with my project. I resolve the conflicts (warnings) and get the "green checkmark" (as I did with the other peripherals), but when I look at the pins on my oscilloscope, there is no activity. What gives?As far as hardware configuration goes, I'm already using the I2C4 bus on the STMod+ Fan-Out Expansion Board, so I'm assuming the STMod+ (CN1) connector is enabled. Is this a good assumption, or is there a jumper on the board that needs to be configured to "fully activate" the STMod+ connector?As far as I can see, all signs are go. I need help determining how my firmware or

..

Hi,I am using a SPC570S-DISP development board, and I am trying to create a new application for it. I have tested out a few example application given in the IDE, and they work fine. I want to develop such an application from scratch. However, there seem to be no guide as such, showing the necessary step to follow in order to properly configure the application. I have also referred the Help section. One problem that I came across is that, in the MCU wizard, I am unable to configure any of the peripherals. When I click on one of the peripherals, no options seem to appear. Is there a document that can be referred, or a tutorial that I can follow?Thanks.Nisal

HiI noticed on my STM32G071.. that the "LL_mDelay(1000)" function did not produce a steady 1000ms delay if I vary the HCLK frequency (code generated by CubeIDE)...I did not have this problem with other MCUs code generated, it worked out of the box (F103/F407).Then I stumbled upon the "LL_Init1msTick(uint32_t HCLKFrequency)" function which seemed to have solved my problem.But what is the proper (dynamic) way to get the HCLK frequency for the function?I currently use this in my main.c: /* USER CODE BEGIN SysInit */ LL_Init1msTick(RCC_GetHCLKClockFreq(RCC_GetSystemClockFreq())); /* USER CODE END SysInit */This seems to pass a valid HCLK to the function. But CubeIDE tells me a warning that:../Core/Src/main.c: In function 'main': ../Core/Src/main.c:85:18: warning: implicit declaration of function 'RCC_GetHCLKClockFreq'; did you mean 'LL_RCC_GetCECClockFreq'? [-Wimplicit-function-declaration] LL_Init1msTick(RCC_GetHCLKClockFreq(RCC_GetSystemClockFreq())); ^~~~~~~~~~~~~~~~~~~~ LL_RCC_Get

1) Set output high2) When input is low wait till it is high3) When input is high read 6 characters4) When having read 6 characters then output low and return (or leave while loop)void Get_Instruction(){   HAL_GPIO_WritePin(GPIOA, GPIO_PIN_12, GPIO_PIN_SET);    while (HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_11)==0)          {          if (HAL_GPIO_ReadPin(GPIOA, GPIO_PIN_11)==1)             {             for (;;)                 {                 HAL_UART_Receive(&huart1, RXbuffer, 6, 1000);            &

My company is currently in the process of developing a embedded UI and we had been hoping to use Emerging Display Technologies ETEML10100XDH6 board as it is has a pre built template by TouchGFX and can easily be flashed from the designer. We were sent the ETEMB101008XDRAM instead, due to supply and price, which is almost identical barring the use of a STM32H7 vs the STM32F7 on the ETEML. Is there any plan to provide a prebuilt template for the ETEMB or will I need to follow the process of flashing a custom board due to the differing MCU's or is there something I can do with my current designer project, such as building the binaries and flashing using ST-LINK?

hello,is there any recommanded speed limits (in rpm) to get an optimal and realiable speed control using FOC?thank u :beaming_face_with_smiling_eyes:

What I want to achieve is starting the DFU ROM bootloader (like on a MCU) from a running Linux (maybe via a dedicated kernel module) or, if this helps, via re-configuring u-boot and doing a software reboot cycle.

Hey there.. iam currently working with a L432KC on a custom made PCB.My programm reads a sensor value (I2C) and sends it so another device via SPI.This operation is performed every minute.iam using the HAL_Delay(60000) command to wait fot the next minute.is that a smart and powersaving solution?what Lowpower modes should i use? my project will be powered through a CR1632 and i want it to last as long as possible. i connected a 32khz xtal as LSE.HAL_Delay() uses SYSTick as timer right? is that meant by RTC ?speaking : if i set the controller into the "shutdown" mode (with disables everything). will it be able to wakeup after a HAL_Delay() function?annother question:Iam using SPI, I2C and UART when my controller is doing someting (not in sleepmode) wich power mode should i use then? i cant find SPI in the peripherals table ..what should i configure in the clock config in the .ioc file?i dont really get it ... thank you!

Hello,In my application, I need LSM6DSL to generate an interrupt when configured FIFO threshold is reached. I am using FIFO for accelerometer and gyroscope.My configuration is as below,FIFO_CTRL5 = 0x09 // ODR 12.5 Hz, FIFO modeCTRL3_C = 0x 44 //BDU, Reg addr incrementFIFO_CTRL1 = 0x3C //Fifo thresholdINT1_CTRL = 0x08 //Route fth signal on INT1 pinCTRL1_C = 0x48 //Select LPF BW, Set ODR and FSFIFO_CTRL3 = 0x09 //Set FIFO ODR for gyroscope and accelerometerCTRL2_C = 0x18 //Set gyroscope ODR and FSAfter this configuration I can see that Watermark flag getting high when the configured threshold level for FIFO is reached. But I am not able to get the interrupt on INT1 pin for the same event.Please help me if I am missing anything.Thanks in advance.

when I am rotating the text by 270 in setup screen() . From the handleTickEvent I am changing the wildcard text as well as I am also changing the position height and width though I am getting text but it is grainy...not clear(I have included invalidate() function also Load in this Image).I tried changing alpha and various height and width but still I am getting grains.....

Hi,I’m trying to use the CR95HF in what I think should be the simplest mode. Reading a 14443a tag.I am controlling it from a pic micro. I have detailed exactly what I have done. Clearly the SPI is working but I am also missing something. Really appreciate it if somebody could have a look and suggest where I may have been going wrong. I know I have not been poling but I have been leaving quite a long time ( several seconds) between sending and attempting to receive. The board is bespoke but built according to ST recommendations. I have checked and there is a strong signal in the antenna.1.      Reset Asserting Chip SelectSend 0x01De asserting Chip Select2.      Next I cyc le the /irq_in while SSI_0=1 and SSI_1=0 to select SPI mode3.      To check the comms are working I do and IDN commandAssert Chip SelectSend 0x00             &n

..

I am a new user of STM32CubeIDE using a NUCLEO-STM32WB-Nucleo board. I want to build an empty project using enabled BLE components using the STM32-WPAN pack version 1.9.0.After selectint RTC, HSEM and RF1 in addition to the default settings plus enabling the WPAN middleware (all default) it autocreates the code files. When I build the project I can reproducibly get the following error:arm-none-eabi-gcc "../Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/shci/shci.c" -mcpu=cortex-m4 -std=gnu11 -g3 -DUSE_HAL_DRIVER -DDEBUG -DSTM32WB55xx -c -I../Core/Inc -I../Drivers/STM32WBxx_HAL_Driver/Inc -I../Drivers/STM32WBxx_HAL_Driver/Inc/Legacy -I../Drivers/CMSIS/Device/ST/STM32WBxx/Include -I../Drivers/CMSIS/Include -I../STM32_WPAN/App -I../Utilities/lpm/tiny_lpm -I../tiny_lpm -I../Middlewares/ST/STM32_WPAN -I../Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread -I../Middlewares/ST/STM32_WPAN/interface/patterns/ble_thread/tl -I../Middlewares/ST/STM32_WPAN/interface/patterns/ble_threa

Hello​I want to rewrite code into STM8S103F2P6.​​But I can't build it.​STVD outputted following error massage.​​​Compiling stm8_interrupt_vector.c...cxstm8 +mods0 +debug -pxp -no -pp -l -istm8s_stdperiph_driver\inc -i"C:\Program Files (x86)\COSMIC\FSE_Compilers\CXSTM8\Hstm8" -clDebug\ -coDebug\ stm8_interrupt_vector.cstm8_interrupt_vector.c:​Running Linkerclnk -l"C:\Program Files (x86)\COSMIC\FSE_Compilers\CXSTM8\Lib" -o Debug\test.sm8 -mDebug\test.map Debug\test.lkf #error clnk Debug\test.lkf:1 no default placement for segment .Signature The command: "clnk -l"C:\Program Files (x86)\COSMIC\FSE_Compilers\CXSTM8\Lib" -o Debug\test.sm8 -mDebug\test.map Debug\test.lkf " has failed, the returned value is: 1exit code=1.​test.elf - 3 error(s), 0 warning(s)​How do I solve this error?​​Please let me know if you have any missing information.​

Here is my schematic and board. I'm wondering if someone can verify that I have everything that's needed on the stm32f4. I can't connect with SWD to the core. My JLink tries multiple times and fails. When I press the reset button on my board the JLink's LED turns red so it seems that the connection between my board and the JLink is correct. I've found a mistake in my crystals' capacitor values, but I don't think that should cause this issue?

Hello,We have problems with the touch screen performance. Is there a way to make this better?We are using the TouchGFX Example project with the same poor results "Smart Embedded display 7.0" with the "Swipe Container Example".Basically if I hold my finger on the Swipe Container, the swipe container continuously wiggles left/right even though I am keeping my finger as still as humanly possible. We observe the same behavior with a Slider widget. We initialize with these settings in our custom application, which then has slightly better performance than the example. hal.setTouchSampleRate(2); hal.setFingerSize(20); hal.setDragThreshold(5);It seems I have tried every possible combination to try to improve this. Whatever I do, I still get some wiggle. The Example projects perform far worse than this on this display. Any advice would be appreciated.Even a reference to what settings you guys have had the most success with on other boards would be helpful. Maybe I can use that e

Posted on February 28, 2018 at 07:26 Hello, I'm trying to implement MotionFX in my application. So far I have a very basic setup which executes correctly. MotionFX_initialize(); MotionFX_GetLibVersion(ver); printu(ver, 1); MotionFX_getKnobs(&iKnobs); iKnobs.output_type = MFX_ENGINE_OUTPUT_ENU; iKnobs.LMode = 1; iKnobs.modx = 1; MotionFX_setKnobs(&iKnobs); MotionFX_enable_6X(MFX_ENGINE_DISABLE); MotionFX_enable_9X(MFX_ENGINE_ENABLE);�?�?�?�?�?�?�?�?�?�? Then, in a thread, I pull data out of my sensors and push it to the motionfx: MFX_input_t data_in; MFX_output_t data_out; data_in.acc[0] = mptr->acc.AXIS_X * FROM_MG_TO_G; data_in.acc[1] = mptr->acc.AXIS_Y * FROM_MG_TO_G; data_in.acc[2] = mptr->acc.AXIS_Z * FROM_MG_TO_G; data_in.gyro[0] = mptr->gyro.AXIS_X * FROM_MDPS_TO_DPS; data_in.gyro[1] = mptr->gyro.AXIS_Y * FROM_MDPS_TO_DPS; data_in.gyro[2] = mptr->gyro.AXIS_Z * FROM_MDPS_TO_DPS; data_in.mag[0] = mptr->mag.AXIS_X * FROM_MGA

Hello,I am trying to use the STM32WB55 Nucleo Pack to develop a BLE application. I am using cubeMX with the STM32Cube_FW_WB_V1.8.0 pack to generate code for the MB13355C nucleo board with STM32WB55RGV6 MCU.I have successfully set the BLE advertising settings and can read the ad with the nRF Connect app on my smartphone. But when I tried to connect my phone to the board, I couldn't get GATT services back. However the connection is successful because the card indicates to be connected as a server. Has anyone ever had this problem? And how can I solve it?Thank you for your reply!

Is there any information on moving (porting?) from CubeMx 5.1.0 and SW4STM32 to the latest Stm32Cube IDE? I attended an online demo a few months ago and seemed like the set up is quite different from what I am currently using. What would be the advantages to spending the time on a current project or even switching to the newer IDE for future projects? Thanks for any help.-Phil

Hello, can we expand or use external RAM with stm32h743vit6? Could anyone guide me for the same?

Hi,I am working on ASM330LH in Linux. After enabling ASM drivers, IIO drivers in kernel and adding asm node entry in device tree, the device is getting detected.target:/sys/bus/iio/devices # lsiio:device0 iio:device1 iio:device2 iio_sysfs_triggerBut scan_elements and some other entries are missing in the device.target:/sys/bus/iio/devices/iio:device0 # lscurrent_timestamp_clock hwfifo_watermark_max  in_accel_y_scale powerdev      in_accel_scale_available in_accel_z_raw sampling_frequencyevents     in_accel_x_raw   in_accel_z_scale sampling_frequency_availablehwfifo_flush   in_accel_x_scale   name    subsystemhwfifo_watermark  in_accel_y_raw   of_node   uevent Can anyone support me in configuring the chip in Linux? Is interrupt configuration required for scan_elements?Regards,Naveen