Solved

Hi all, I got back on a project on the SPC574K2 I paused a few months ago and decided to start over from a green-field environment.I then downloaded and installed SPC5Studio 6.0.0 Doyle which came along with version 1.16.1.20210914101245 of the LLD sdk.Unfortunately my project builds fine but it is not running anymore due to a problem in board clock management (I', using the EVBoard)To have proof of evidence for this I re-installed 6.0.0.Asimov (which instead comes with LLD version 1.13.1.20200626121018 with which, instead, my code (AND the EXAMPLES provided by ST) builds and runs just fine Needless to say I'm pretty unhappy of this finding which came out without any explicit notice >:( Has anyone run into similar issues? how did you got away?Thanks in advance

Hi,we have designed a custom board, based on STM32MP151 and OpenSTLinux 5.10. On this board we use the switch NXP SJA1105S with 3 phys and a MAC-MAC interface between the MPU and the switch. All ports are configured for RGMII mode. At startup(via modprobe) the SJA1105 driver tries to load a default configuration that assigns multiple vlan ids to the ports. Unfortunately it looks like, that the stm32-dwmac driver does not support this by default, because it outputs the message "Only single VLAN ID supported". Is there a possibility to change this behavior of the stm32-dwmac driver?Example Output:[  80.801160] sja1105 spi2.0: Probed switch chip: SJA1105S[  80.934971] sja1105 spi2.0: Updating VLAN 1025[  80.943584] sja1105 spi2.0: Updating VLAN 1025[  80.952858] sja1105 spi2.0: Updating VLAN 1025[  80.961709] sja1105 spi2.0: Updating VLAN 1025[  80.967525] sja1105 spi2.0: Updating VLAN 1025[  80.977959] stm32-dwmac 5800

root@stm32mp1:~# timedatectl status Local time: Thu 2021-10-14 15:10:06 UTC Universal time: Thu 2021-10-14 15:10:06 UTC RTC time: Sat 2000-01-01 00:00:38 Time zone: UTC (UTC, +0000) System clock synchronized: no NTP service: active RTC in local TZ: noMy RTC is out of sync.This is the date loaded after every boot. Where does system clock get it? This is the timesyncd service.[[0;1;32m*[[0m systemd-timesyncd.service - Network Time Synchronization Loaded: loaded (/lib/systemd/system/systemd-timesyncd.service; enabled; vendor preset: enabled) Active: [[0;1;32mactive (running)[[0m since Thu 2021-10-14 15:09:43 UTC; 2min 23s ago Docs: man:systemd-timesyncd.service(8) Main PID: 373 (systemd-timesyn) Status: "Idle." Memory: 576.0K CGroup: /system.slice/systemd-timesyncd.service `-373 /lib/systemd/systemd-timesyncd   Sep 20 10:44:02 stm32mp1 systemd[1]: Starting Network Time Synchronization... Sep 20 10:44:03 stm32mp1 systemd-timesyncd[373]: System clock time unset or jumped

I'm trying to read a T2T tag with NFC card reader, Nucleo expasion board attached to STM32F103 Nucleo board. I'm using an example from X-CubeExpansion_NFC3This tag is well formatted with NDEF, but when I try to read with this example, I get an error in ndefPollerNdefDetect(). This funtion returns ERR_PROTO.If I read this tag with any other application, I can read it content.Can you help me with this problem. I'm sure, I'm doing something wrong, but I don't know what isThank you in advance, looking forward to hearing from youCarmen

Hi,how to differentiate both chips, if they have the same value for WHO_AM_I register?I know that I could read couple times the accelerometer values, calculate magnitude over all axis and check if the value is near 1g or 0.5g (assuming no movement during measurements), but this will not work if any HP is enabledIs there a simpler way?BR

I am looking for accelerometer ultra low noise with low g.I want to connect 4 sensors using I2C, so I need 2 pin SA0 and SA1.Do you have such sensors

Hi all,I am pretty new to the STM32 world and I have just started to play around with the STM32F429 discovery kit and STM32CubeIDE. I am OK with the basic & introductory projects, and I was able to have basic IO operations like LED blinking run properly. When I tried to first dig into the FreeRTOS concepts, I realized that I'm having issues with the osKernelStart() call taking place in "main.c". (If I comment out this line, the code builds and runs ok "enough" to blink LEDs.)To make sure that my own code is not affecting the behavior, 1) I started a clean STM32 project using STM32CubeIDE, 2) modified no config at all, 3) directly generated the code4) built the project5) started a debug session6) Debugged the code using "Step Over" When I hit the Step Over again when it's on the line where the osKernelStart() is being called, the debugging step options (Step Into, Step Over, Step Return) are all grayed out but the debug session seemed to continue working.To

Board Name : stm32f7 seriesQUADSPI : N25Q128AI am stored imaged data in nor flash, data stored correctly in memory. After i am reset the controller or power on the controller, data will be resetExample :data : 0xD3005600Data stored first time programming : D3005600after reset the controllerRead the stored data : D3885688Why 0 data replaced as 8 in qspi memory ?data stored programming time : after rest the controller, read the qspi data :

Hi All,I want to use DMA to receive unknown length data. So I config USART_IT_IDLE and DMA_IT_TC and set DMA_BufferSize = 30 bytes. When the length of received data is less than 30 bytes, It works correctly and enters the USART1_IRQHandler(void) function. But the length of data is equal to 30 bytes, it enters the DMA1_Channel5_IRQHandler(void) function first then enters the USART1_IRQHandler(void) function again. Why does the length of data be equal to BufferSize cause Idle interruption?void RCC_Configuration(void) { RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_USART1 ,ENABLE); RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1,ENABLE); }   void GPIO_Configuration(void) { GPIO_InitTypeDef GPIO_InitStructure;   GPIO_DeInit(GPIOA); GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9; // TX GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOA, &GPIO_InitStructure);   GPIO_InitStructure.GPIO_Pin = GP

Good morning,I've been fighting with an L496, trying to get it to jump into the bootloader.I'm using STM32CubeIDE 1.7.0 on a Nucleo-L496ZG.The code is based on a new project for the Nucleo board, hints from AN2606.Just to make sure that I wasn't too far off, I pulled out the "FLASH_JumpBootloader" sample program for the F769 and got it running on my F767 Nucleo, then pulled the important bits into a minimal test program. It works well, jumps right into the bootloader and I can attach to the board as a DFU.So I altered the start address for the L496 and the thing is fighting me. It just reboots the processor. I even tried it on a new L496 Nucleo, but it acts the same.Here's the code's important bits: /* USER CODE BEGIN WHILE */ while (1) { /* USER CODE END WHILE */   /* USER CODE BEGIN 3 */ typedef void (*pFunction)(void); pFunction Jump_To_Application; uint32_t JumpAddress;   if (HAL_GPIO_ReadPin(B1_GPIO_Port, B1_Pin) == GPIO_PIN_SET) {   JumpAddress = *(__IO u

Hi,I had a question regarding Bruno's excellent series on creating a simple bootloader.In part 3, there is an if statement which checks if something has in fact been loaded into the applications's flash region:// bootloader main.c if( ( *(uint32_t *) FLASH_APP_ADDR ) & 0x2FFE0000 ) == 0x20000000 ) { // jump to app main... }The logical AND operation against the dereferenced FLASH_APP_ADDR with a mask that I don't understand, should yield an initial SP.What does 0x2FFE0000 signify?Many thanks,Dan

..

Hello,I want to use the STM32L562QE-DK board to measure the current for my own developed PCBA. There is a connector CN20 that can be used for this purpose as written in the schematic for the board:Output connector to supply and measure external target:PIN 1: GNDPIN 2: Voltage source, current is not measured, it is not a copy of ourput voltagePIN 3: Output with current measurementPIN 4: Output voltage copy with 150R protection serial resistor, current is not measuredBut there is no voltage on Pin 3? And in the user manual for the board I also did not find anything.Where can I find documentation how to configure the board for this purpose?Thanks,Wolfgang

Hi,On the DK2 board, there is a LBEE5KL1DX-883 from Murata. But I want to use their LBEE5HY1MW (Type 1MW - LBEE5HY1MW | Wi-Fi® Modules / Wi-Fi® + Bluetooth® Modules | Murata Manufacturing Co., Ltd.) in my design. But on their site, they only mentions 'NXP I.MX Linux' . As ST has tried 1DX, will 1MW work on ST's Linux distribution? Furthermore, what about other WiFi modules on the market? Is it easy to run them with STM32MP15x?Thanks.

Hello,I tried to impelement a simple SPI Echo Slave.The Master transmits Data (Example for Nucleo 474RE - Master Full Duplex Interrupt) and the Slave waits for reception using HAL with a datasize of 1 Byte.After the Transfer is completed I am copying the received Byte into the Buffer for the next TX Byte and waiting for the next Transfer again.When receiving Data, every second Byte received gets dropped, and when trying to echo it, undefined data is sent.As seen in the Image, the first Channel is MOSI, the second Channel is CLK, the third Channel is MISO. The Slave should transmit the identical message sent by the Master, starting with the second Byte./* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * <h2><center>© Copyright (c) 2021 STMicroelectronics. * Al

Is there a good way for multiple people to develop their screens and integrate them into the same TouchGFX project?

Hi all,I would like to use the Cryptographic peripheral in my STM32L451 to encode and decode some data based on a pre-stored common key.Are there any examples for Atollic that would get me started on this?

HelloI intend to use SARADC with DMA and I'm not able to configure it. SPC5 Studio provides examples that I'm using but in the configuration options of other SPC5 models in SARADC Configurations the option DMA configuration appears. On SPC58EE84E7 does not appear. How should I proceed?Thank you!!

Hello, I am a Newbie.I have one IC marking number.I have to find the stm part number and its datasheet.Anyone please help me.Marking Number: SPC5777CCMME3 3N45H CTUS2052A PZUSCTA

..

Hi sir , I working with( LSM6DSL)STEVAL-MKI178V1 Dk board communicating with nrf52840 controller board.i am able work pedometer and significant motion and tilt detection these modes are working but i am trying to generate free fall detection but i am not getting the out put .here i am sharing the code let me know where i am missing.  /* set output data rate to 416 Hz and enable X,Y,Z axis */ LIS6DSH_write_reg(LSM6DSL_ACC_GYRO_CTRL1_XL, 0x60); //0x20 5hz ,50 204hz     /* Enable free fall interrupts and latch interrupt */ LIS6DSH_write_reg(LSM6DSL_ACC_GYRO_TAP_CFG1, 0x81);     /* Tilt detector interrupt driven to INT1 pin   */ LIS6DSH_write_reg(LSM6DSL_ACC_GYRO_WAKE_UP_DUR, 0x00);     LIS6DSH_write_reg(LSM6DSL_ACC_GYRO_FREE_FALL, 0x33);     /* free fall event is enabled */     LIS6DSH_write_reg(LSM6DSL_ACC_GYRO_MD1_CFG, 0x10);i am reading the 1B regi

Hello together,after a lot of trouble getting the USB HS port working on the STM32H747 on the STM32H747I-DISCO Discovery kit I’m stuck again. I’m using STM Cube IDE 1.7 and the HAL USB CDC lib.I was able to get USB CDC working on the M4 thanks to https://community.st.com/s/question/0D53W000002diUsSAI/stm32cubemx-h7x5h7x7-usb-cdc-bugOn the M7 core it kind of worked out of the box. But when I want to use it with the USB interal DMA enabled it didn’t work at all.I already figured out I have to disable the D-cache and not use the DTCM SRAM for the buffer: https://community.st.com/s/article/how-to-enable-dma-in-usb-with-stm32h7-devicesI provided a minimal example of code which already results in failure: ...   MX_GPIO_Init(); MX_USB_DEVICE_Init();   HAL_Delay(1000);   uint8_t buffer1[2000], buffer2[2000];   CDC_Transmit_HS(buffer1, 1468); HAL_Delay(50); CDC_Transmit_HS(buffer2, 4);   while (1) { /* USER CODE END WHILE */   /* USER CODE BEGIN 3 */ }W

Hi, everybody!Referring to this topic, I'm still have issue with USB2514 USB HUB:https://community.st.com/s/question/0D53W000015a2V8SAI/-120369992-dwc2-49000000usbotg-overcurrent-change-detectedThe description of the problem changed a lot. Currently I'm have two same board with same components and schematic and same images loaded.One of the board have no problem with USB HUB. All working fine, second board have problem with high speed USB devices:Here are dmesg's:keyboard/mouse (full speed):[ 1449.719724] usb 1-1.1: new full-speed USB device number 11 using ehci-platform[ 1449.882209] input: Logitech USB Receiver as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C534.0001/input/input1[ 1449.961800] hid-generic 0003:046D:C534.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-5800d000.usbh-ehci-1.1/input0[ 1449.987711] input: Logitech USB Receiver Mouse as /devices/platform/soc/5800d000.usbh-ehci/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C534.0002/i

As per the application note AN4967 Rev 7 AT+APPKEY command has been removed from the firmware of AT_SLAVE. I would like to know how can i set or enquire the APPKEY via AT Commands. Also is there possibility to set this key in firmware itself? Since as per the lora standard for OTAA activation, user should setup APPEUI, DEVEUI and APPKEY. But since command for AppKey removed so i wonder how can i set this key on module. Please update and share if there is any good reason to remove or the way to set the key in firmware itself.

Hi There We need this stock STM32L496VET6. Please help us out,