About sheqom

sheqom · 2024-01-06

Hello,With STM32F411E-DISCO, I am trying to obtain the RPM value by receiving data from the hall sensor of the BLDC motor. For this, I activated XOR On / HALL EFFECT Mode and connected the pins of the hall sensors to the relevant places.HAL_TIMEx_Hal...

sheqom · 2023-12-20

I am transferring sensor data between Jetson Nano and STM32F411E-DISCO via can using 2 MCP2515. On the STM32 side, imu and encoder sensors are connected and constantly transmit data to Jetson nano via canbus.However, due to a problem that I do not fu...

sheqom · 2023-12-16

Hello, I am receiving data on my STM32F411E board via the I2C interface with the Mpu9255 IMU sensor. I get HAL_BUSY status in case of any power outage or re-debug.https://stackoverflow.com/questions/69912431/issue-in-the-i2c-communication-stm32-hal-l...

sheqom · 2023-12-15

Hello, I am trying to take imu and encoder data in Stm32 and transfer it from can network via mcp2515. When I try to transfer data in the encoder, it works without any problems when I apply CANSPI_Transmit in the callback function.However, CANSPI_Tr...

sheqom · 2023-12-14

Hello, by connecting an mcp2515 to Stm32, I enabled it to communicate properly with other cards via the Can network. However, when a message arrives, I couldn't understand how to receive it with the INT pin and I couldn't do it. I tried connecting th...

sheqom · 2023-12-23

https://forums.developer.nvidia.com/t/jetson-nano-4gb-mcp2515-can-bus-receiving-wrong-id/192810Based on the solution here, I set the spi max frequency values to 2 Mhz and the problem was solved. I thank you.

sheqom · 2023-12-21

Update: Outgoing data from Jetson is transmitted with full accuracy, but there is a problem with the incoming data to Jetson. I suspect there may be a problem with the Jetson nano's MCP driver.

sheqom · 2023-12-16

HAL_I2C_DeInit(&hi2c1); Calling this before (just below if) fixed it. I think there is no problem right now, thank you everyone for your efforts, I will be here if there is a problem again :)

sheqom · 2023-12-16

HAL_StatusTypeDef ret; uint8_t ok = 1; void reset_I2C(){ GPIO_InitTypeDef GPIO_InitStruct = {0}; ret = HAL_I2C_Mem_Read(&hi2c1, 0xD1, 0x75, 1, &ok, 1, 1000); if (ret != HAL_OK){ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD; GPIO_InitStruct.Pin ...

sheqom · 2023-12-16

Can you share your solution? I'm having exactly the same problem but I couldn't solve it.

User statistics

User Activity

STM32F411E-DISCO BLDC HALL SENSOR

When transferring data via mcp2515 on stm32, the values are reduced by half.

I2C HAL_BUSY

STM32F411E-DISCO cannot send Can data via I2C interrupt

STM32F411E-DISCO and MCP2515 INTERRUPT

Re: When transferring data via mcp2515 on stm32, the values are reduced by half.

Re: When transferring data via mcp2515 on stm32, the values are reduced by half.

Re: I2C HAL_BUSY

Re: I2C HAL_BUSY

Re: How to recover I2C in stm32 STM32H743 after an error or a locked state which can come due to a g