Solved

"CUBE IDE" İLE projesinde aşağıdaki hataya düştüğünde, ne anlaşılmayacağına dair bir bilgi yok. Bana bu konuda yardım eder misin? error: "'LOARA_TX_RX_end' projesinde açık bir yerleşim seti yok."proje Adı > 'LOARA_TX_RX_end'

I am trying to configure MPU of stm32f407g-disc1 board for FreeRTOS. But i am not able to get any reference or any documentation related to it. Can anybody please help me?

I am succeded connect and initialize the flash with UDE STK 5.2, but when I try to program the flash with memtool, the program button is unclickable.where's the step I am missing?

I'm completely new to embedded system development. Bought an evaluation board from Amazon. I tried to convert the ST-Link to J-Link by following these instructions: https://www.segger.com/products/debug-probes/j-link/models/other-j-links/st-link-on-board/. But in  SEGGER STLinkReflash, when I choose [1] Upgrade to J-Link, it showed ST-Link not found. I used a micro USB B to USB A cable to connect the board to the PC. LED for power was staying on. LED3 was blinking quickly. LED4 was blinking slowly. Button1 was functional. It could choose which LED from LED1-LED3 to blink. I have tried the connect the board to three Windows devices(a desktop, a laptop, and a surface). All the results were the same. I suspect ST-Link driver was not functioning well. But I can't tell.

Hi everyone,reading the official TouchGFX documentation, in the section "Backend Communication->example",ST people say that there are examples for STM32F746G Discovery Kit that explains in detailshow to interact between TouchGFX thread and other threads via intertask communication.I installed the latest TouchGFX Designer package (4.22.0) where they say that the mentionedexample can be found into folder Demos -> Board Specific Demo, but I have not found it.Can someone tell me the packages or the tools where I can find those examples?Thanks in advance to everyone will help me.

For learning (and suffering) purposes I am trying to write my own USB Driver in device mode. Right now I am just trying to successfully enumerate the device. So far I am able to read SETUP packets but when writing to EP0 (IN transfer) the requests seem to timeout at 5 seconds (seeing this through Wireshark). I am using a STM32F401CCU6 chip.For example, this is what happens when a GET_DESCRIPTOR request is made: USB URB [Source: host] [Destination: 3.0.0] URB id: 0xffff9d142a6f8900 URB type: URB_SUBMIT ('S') URB transfer type: URB_CONTROL (0x02) Endpoint: 0x80, Direction: IN Device: 0 URB bus id: 3 Device setup request: relevant ('\0') Data: not present ('<') URB sec: 1688842172 URB usec: 857980 URB status: Operation now in progress (-EINPROGRESS) (-115) URB length [bytes]: 64 Data length [bytes]: 0 [Response in: 58] Interval: 0 Start frame: 0 Copy of Transfer Flags: 0x00000200, Dir IN Number of ISO descriptors: 0 Setup Data bmRequestType: 0x80 bRequest: GE

Hi all.In my openstlinux yocto image has been included the SGTL5000 audio codec management. I have a problem. On the headphone output I heard only a continuous pink noise.These are some information from my system:zcat /proc/config.gz | grep SGTL CONFIG_SND_SOC_SGTL5000=y:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: STM32MP1 [i.Core STM32MP1], device 0: 4400b004.audio-controller-sgtl5000 sgtl5000-0 [4400b004.audio-controller-sgtl5000 sgtl5000-0] Subdevices: 1/1 Subdevice #0: subdevice #0 :~# aplay -L null Discard all samples (playback) or generate zero samples (capture) pulse PulseAudio Sound Server default Default ALSA Output (currently PulseAudio Sound Server) sysdefault:CARD=STM32MP1 i.Core STM32MP1, 4400b004.audio-controller-sgtl5000 sgtl5000-0 Default Audio Device The command:~# speaker-test -c 0 -t sine -f 2500seems to add a "sine" signal on the output but the pink noise always remains.The command:~# amixer -c0 sset Headphone 0switch-off the signal outputHow can

dfu-util is an open source DFU memory reader/writer.I ported the source to Windows 10 x64.Worked fine, downloading firmware, to STM32H7B3I DISCOVERY board.Fails with STM32H7B3I EVAL board, apparently because the EVAL board identifies itself as three separate DFU devices, unfortunately with identical serial numbers:Found DFU: [0483:df11] ver=0200, devnum=62, cfg=1, intf=0, path="1-6", alt=2, name="@OTP Memory  /0x1FF7000/01*1024 e", serial="FFFFFFFEFFFF"Found DFU: [0483:df11] ver=0200, devnum=62, cfg=1, intf=0, path="1-6", alt=1, name="@Option Bytes  /0x1FF8000/01*128 e", serial="FFFFFFFEFFFF"Found DFU: [0483:df11] ver=0200, devnum=62, cfg=1, intf=0, path="1-6", alt=0, name="@Internal Flash  /0x08000000/256*02Kg", serial="FFFFFFFEFFFF"Any easy way to resolve this with dfu-util?Or do I need to "educate" dfu-util in the matter of "alt", which varies with memory region?

 I am using Sprintf, but I cant see the number in UART LPS22HH_pressure=LPS22HH_GetPressure();   sprintf(result,"%4.2f", LPS22HH_pressure); // @suppress("Float formatting support")I have also tried %g

I need to copy text from internet to Cube IDE main.c file.I copied the text from the internet, I click in the Cube IDE context menu "paste". And nothing happens. If I copy text from Cube IDE and paste that text into Cube IDE, then the text is pasted. I tried to copy text from the Internet first to a text editor, and then to Cube IDE, but still no text is pasted. Cube IDE restarted.If I create a new Source File C and try to insert into it, then nothing is inserted into it. (If I copy something from the Internet to this Source File.) What's the matter?Nothing can be copied from Cube IDE either. I'm trying to copy text from Cube IDE and paste this text into notepad. It won't work.

Dear ST Engineers,I am planning to port this device driver to another 8 bit MCU:https://www.st.com/en/embedded-software/stsw-img023.htmlMy 8 bit MCU has I2C slave address range from 0x00 to 0x7F.However, hint of that ST driver code insists on using uint16_t as I2C address, for example, typedef struct { /* To be filled with customer's platform. At least an I2C address/descriptor * needs to be added */ /* Example for most standard platform : I2C address of sensor */ uint16_t address; } VL53L5CX_Platform; How do I reconcile this conflict?  Or do I misunderstand something about ARM 32 bit architect?Please give your valuable opinions.  :cowboy_hat_face:

Hellofriends, I am trying to make a dual core example on the Wio-E5 STM32WLE5JC Module. I made all the settings as in this video.  However, only CM4 works when debugging. CM0PLUS is not working and I am getting this error Target unknown error 32Error in initializing ST-LINK device.Reason: Unknown. Please check power and cabling to target. I tried this on STM32Cube ide 1.7.0 and 1.8.0.

I'm using a NUCLEO-H563ZI board with the onboard st-link, Cube IDE 1.12, on an intel mac running macos 13.4.1. What I'm observing is that when I start a debug session is that if I set a breakpoint and hit continue i'll hit the breakpoint almost instantly, but if I click step-over it can take 10 or more seconds to hit the next line of code. I launched the st-link_gdbserver from the command line and used command line arm-none-eabi-gdb and had the same behavior. If I did `b main.c:80` and then continue i'd hit the line instantly, but if I hit `u` in gdb it could take 10 or more seconds to get to the next source line. It isn't always the same source lines, sometimes a line that took 10 seconds will be instantaneous the next time you try it.I have a few coworkers reporting similar behavior.  Any Ideas? The st-link reports a 8000KHz link speed. I'm not sure where the issue is in the chain. I attached a video demonstrating the issue, sorry for the low quality I had to fit in th

Hello, I am using CUBEMX V6.9.0. However, still encountering problem that occurs during initialization from CUBEMX. Following lines are generate the error.  /* DCMI DMA DeInit */HAL_DMA_DeInit(hdcmi->DMA_Handle);HAL_DMA_DeInit(hdcmi->hdmarx);HAL_DMA_DeInit(hdcmi->hdmatx);Error code is shown below../Core/Src/stm32h7xx_hal_msp.c: In function 'HAL_DCMI_MspDeInit':../Core/Src/stm32h7xx_hal_msp.c:226:25: error: 'DCMI_HandleTypeDef' has no member named 'hdmarx'226 | HAL_DMA_DeInit(hdcmi->hdmarx);| ^~../Core/Src/stm32h7xx_hal_msp.c:227:25: error: 'DCMI_HandleTypeDef' has no member named 'hdmatx'227 | HAL_DMA_DeInit(hdcmi->hdmatx);| ^~ After commenting lines that generate the error, DCMI is somehow works but other code blocks are not working properly. Is there another solution beyond updating CubeMx or commenting those lines?

Hello,I need to map two different programs (a custom bootloader and the application) in the memory space of my STM32G0, as described in figure.The bootloader should start at power-up, then check the application CRC and eventually jump to it.Both in the bootloder and in the application, I need to remap the interrupt vector table.Where can I find some documentation to do this, in the correct way?Thank you,Carlo

The subject says it all. Am I missing something obvious? Is there a link to "My Posts".Sid

hiI am currently working on a project that utilizes the STM32H753 to acquire images through an image sensor called AR1034.However, the size of the image I am acquiring is 1280*960. Due to the large size, it is not possible to store it inside the MCU, so I want to add an external PSRAM and store it in that memory.I have completed the basic functional test of the basic image acquisition method and memory storage through DCMI, but when I put these parts together, it does not work properly when I try to save the full size of the image I want to acquire.When I researched the data, I found that the size that can be acquired at a time in DCMI is set to 65535, so the image must be divided into data, and it is said that SRAM storage is not possible at the same time, so Double Buffer must be utilized...However, I couldn't find the exact method even after searching, so I'm asking a question. If you have an example or method for this method, please answer.

HiOur incoming inspection unit failed to find any information on ST4SI2M0020TPIFW device marking and it's datasheet.Kindly confirm the same8944477200000753575

All, I would like to first begin with saying thank you for your time in attempting to assist me.Library used: NFC st25r3911b LibraryI am attempting to read and write from/to a tag; more specifically a Type-2 and Type-4. I have been looking through example code which uses the same library as me and stumbled across the following code, shown in nfcDataExchange.png. I have been using the code to try and read/write from/to a tag, but I haven't had much success. Google doesn't seem to be useful for this either, since I only stumble across posts explaining the structure of a NFC Data Exchange Frame (NDEF), but from what I know T2T and T4T tags require different payload structures.So my question is, are there documents available that show how to read/write to a tag and also how to structure the tx buffer depending on the tag type? or is someone willing to explain this to me? or can someone point me in the right direction?Also, given that the example code I looked at had the code shown in the p

Hi,i want to clone my project. I did the following steps:1) Edit > Copy.2) Edit > Paste.3) Rename the ioc files.4) Delete the Debug.launch file.5) Project > Clean.the next step is to generate the CubeMX. But when I try to open the .ioc file this error message occurs:Invalid Input: Must be project's active .ioc file.can anybody help me please?

Hello, Just a quick heads up regarding LL implementation of LSI.It fails to start, while same setup generated for HAL works as it should.Now looking in detail whats wrong in register level calls, will post my results.ST, I hope you will find and fix this issue with LL code generation, thank you !

There is a newly introduced bug in the freshly upgraded package coming with the IDE 1.11. MX_SDMMC1_SD_Init(void) does not configure hsd1.Init.BusWide = SDMMC_BUS_WIDE_1B but directly to the final state choosen in CubeMX (in my case 4B). But the SD requires to be started and configured with 1B before switching to the final configuration. Forcing manually to 1B makes the job, but CubeMX changes it back to 4B after each generation. The easy workaround is to force 1B in the user code at the end of SD_init function.Could you confirm this is a bug and roll back to the correct version ?

Hi, Im new to Touchgfx and came to a problem following the tutorial 4.When I run the simulation it shows declaration error.gui/include/gui/containers/MenuElement.hpp:19:4: error: 'icon' was not declared in this scopeI tried following the hpp from slider examples, but it seems to implement it differently to the tutorial.Any suggestions on how to fix this?Thank you

Hellofriends, I am trying to make a dual core example on the Wio-E5 STM32WLE5JC Module. I made all the settings as in this video.  However, only CM4 works when debugging. CM0PLUS is not working and I am getting this error Target unknown error 32Error in initializing ST-LINK device.Reason: Unknown. Please check power and cabling to target. I tried this on STM32Cube ide 1.7.0 and 1.8.0.

Hi All,I have a custom board with STM32735VGT(this mcu is with 1=quad SPI but using the register octpspi). I am using the micro mt25qL128 NOR flash.I am using the 1-1-1(1 bit instruction, 1 but data) for read and configure the registers, eraseI am using the 1-4-4(1 bit instruction, 4 bits address and data) for read and program.All read registers, configure registers and erase is working fine.Using 1-4-4 to read the flash is working fine too.But when using program flash, the status is ok. I can see WIP and ready bit is correctly changed. But the flag status register read back is 144=0x90. Bit7 means ready. But bit4=1 shows it has failure and protect error or crc error.Please help.