Solved

I have tried to integrated imported examples in spc5 studio. I unbaled to done . Is there any setting you can help me..!!. I have used stm32cube IDE for stm32 series microcontrollers, it is very flexible and easy . Right now i am using spc570sxx series controller, and IDE is SPC5 studio IDE. Please help to integrate imported example applications.

Hello,I have here two Nucleos with an H743 on it. If it is rev Y, it is the "old" 144pin Nucleo board with the break-off ST-link board on top. For this there is a schematics in appendix A of the user manual. But if it is rev V, it is NUCLEO-H743ZI2 , note the 2 at the end, with no break-off possibility and a different user manual. And this manual has no schematics included. A trouble start as I start my project. While the manual says PC9 = MCO2 is on CN8 pin4 and CN12 pin1, I see a signal only on CN8 pin4. No way to check what's going on without schematics.Please ST folks can you provide this somewhere.Thanks a lotMartin

Hi STM32-Community, I'm using an STM32H743 with ADC3 in circular DMA mode. ADC has a clockfrequency of 48 MHz. I'm using 8 channels within this ADC3 and also configured the DMA with said channels each with a sampling time of 64.5 cyles. I'm using an async prescaler of 6.Calculating the sampling rate for a single ADC Channel I get:48 MHz-----------------                                    =  15,504 Hz ~ 15.5 kHz(8 Channels* 6 (Prescaler) * 64.5)I've put a variable within my DMA routine (which does nothing else) and everytime the DMA toggles this variable, I send out the time needed between each DMA interrupt. I consistenly receive 1169 ms with a DMA Size of 65528.65528---------------------------------   ~ 7.005 kHz.(1.169)*8 (ADC-Channels)Where is my error?Here are the ADC Config:/* ADC3 init function */ void MX_ADC3_Init(void) { /* USER CODE BEGIN ADC3_Init 0 */ /* USER COD

Hi ST Community,I'm using the B-L475E-IOT01 card and I want to use the X-CUBE-BLE1 middleware to send information directly to a variable (something I was thinking of doing simply with this application). Only, when I run it and try to debug, I'm having trouble understanding what the program is doing (I'm not a Bluetooth Low Energy expert) but I can't detect the card from the ST BLE Toolbox application. Is this normal, or am I doing something wrong?Thanks in advance!

Hi all,I recently stumbled upon STBC15 and I am interested in integrating it into our next design. However, I am lacking a critical parameter from the datasheet: what is the typical and maximum allowed current flowing from VBAT to the OUT pin?

Heyho,about VCAP / LDO connection in STM32H7 series without SMPS, for example in STM32H733ZGT6 (LQFP-144), when using the internal LDO for core supply.As far as I understand, the VCAP pins are for the connecting buffering capacitors to the internal LDO.I have checked the Nucleo (H723) and Discovery (H735) schematics, and for each pin there's a 2u2 cap, but all pins are connected.Questions:1) Is it a must to connect all the VCAP pins together on the PCB?If so, please give me some valid explanation. Electrically this is one net within the STM32, so I don't see why these should be connected externally, as long as each pin is closely connected to its dedicated external capacitor.In a LQFP-144 package these pins are quite far apart, and I'd like to NOT connect these pins - the layout will be ugly enough.2) Is there an upper limit on the capacitor size?Assuming I don't bring the pins together - see 1) - I'd like to be on the safe side and give each pin a little more than the 2u2 (10u). That

Hello. We recently purchased a complete set of stm32mp157x-Ev. The documentation shows only the main connectors. Where can I find a complete schematic for both boards?

Hey All,So I know it's mentioned in the data sheet that the stm32mp1xx MPU's only support 16/32 bit DDR ram, and that it also mentions the limit of 1GByte total ram,  but I just wanted to confirm this isn't possible and specifically why as I cannot find out much about what is the limiting factor here.For example this IC:https://au.mouser.com/ProductDetail/Intelligent-Memory/IM8G08D3FFDG-125I?qs=Y0Uzf4wQF3k9cXZekshqqQ%3D%3DAlternatively, could I push it up to 2GBytes by adding an additional MPU with its on 1GB of ram whilst also pushing it up as a quad core system?And if so, what the best communication method would be between them.Thanks in advance for any help!

Hi,Im using STM32L031F6P6 mcu for one of my project. Im also using IIS2MDCTR & LSM6DSV16BTR sensor.I need to find heading regarding that i have few doubts.1.Will STM32L031F6 mcu support mems1 package?if no could you suggest a mcu which support the same?2.If mems1 package is not supported by this mcu , is there any libraries available to find heading ? 

 I would like to use the G030C8T6 MCU to use ICS current sampling. Currently, the MCSDK 6.2.1 does not seem to support it. What should I do？@cedric H

Hello everyone.The case may be known, but if it helps...After activating the Master Clock Output (1 or 2) in STM32CubeIDE on PLLP, no signal is present on RCC_MCO output.After analysis the PLL must be activated by adding the initialization in a User Code if no device dependent on this PLL is used (ADC, I2S1 or I2S2):__HAL_RCC_PLLCLKOUT_ENABLE(RCC_PLLPCLK);Regards. 

Hi,If I could find some information about the implementation of the ZeST algorithm, I could try to infer whether it can be used on the B-G431B-ESC1 looking its schematic, but I can't find anything about it. So, will this new algorithm be available on the B-G431B-ESC1 board, or it needs some specific hardware to measure some extra parameter?If I deduced correctly, the ZeST algorithm is able to calculate the angle of the motor's shaft, I guess that having into account the effect the inductance change produces on the signal, like a variable inductor dependent on the shaft's angle, is that right?Thanks!

I saw on NUCLEO-U5A5 schematics - there is a level shifter for signal T_VCP_TX:a bit obvious: if MCU jumper is set to run on 1V8 VDD - an external UART receiver (e.g. CP2102N) would not get anymore correct UART_TX signals (yes, it does not anymore with 1V8 logic on TX).Wouldn't it be enough to use an Open Drain signal on MCU (for UART_TX) and an external pull-up to 3V3?The UART_RX should be OK, even MCU on 1V8 MCU VDD, but assuming RX is 5V tolerant.Here what I mean - and it works!Just configure the UART_TX as GPIO_MODE_AF_OD and it should work also without a need for a level shifter (with external pull-up).

I am running macOS Sonoma and using PlatformIO within Visual Studio Code.I have multiple STM32 microcontrollers connected via ST-LINKs to a USB hub¹. My ST-LINK USB devices are correctly listed in 1) the USB Device Tree within the macOS System Information, and 2) via Terminal when using `st-info --probe`.I am also able to utilise these ST-LINKs to upload code to a single microcontroller individually. Even when all are connected I am able to upload code to one of these microcontrollers.However, this happens semi-randomly. I cannot specify to which of these connected microcontrollers my code is being uploaded.I am aware that I need a serial device address to define `upload_port` in my platformio.ini file. To find this address I am using `ls -l /dev/cu.*` in the Terminal. But the only port being returned is `/dev/cu.Bluetooth-Incoming-Port`.Why isn’t `ls -l /dev/cu.*` showing the serial addresses of my connected ST-LINK devices? After several days of troubleshooting without any success, I

..

Hello,which interfaces does a virgin STM32C0 in SO8N offer on the first boot for programming? AN2606 says USART1 and I2C1. In other cases, AN2606 adds a note when SWD does not work, but no such note is there for STM32C0. So, I assume SWD is supported too. However, while SWD is on PA13 and PA14 and I2C1 is on PB6 and PB7, PA14 and PB6 is muxed to the same pin in the SO8N package. So, this seems like a conflict. Did I understand something wrong?If SWD is not supported in the bootloader, is there a way to prevent the bootloader (for example, with the BOOT0 pin)? I want to put SWD on a pin header for debugging anyway and it would be annoying to need extra pins just for the initial programming.

I'm using an STM32H745 and have developed the Boot code, which works as expected when built as part of an application.  However, having converted the Boot code to a static library and linked it into the same application the Boot startup section .isr_vector is not detected and hence not located at the appropriate location defined by the Application linker script.Is there something I need to add, either to the Boot library or the Application so that the library section get located at the correct address?Other than making the Boot source code a library, rather than part of the Application nothing else has changed.

Hi,I am trying to understand Trustzone concepts by building my own project. I’m using STM32U5-EVK and I went through the example project(GTZC_MPCWM_IllegalAccess_TrustZone project)to understand the basics. However, in this project, I noticed that they have not enabled the SAU in .ioc file, but still the SAU_CTRL_ENABLE macro has been set to 1. Also, on debugging I saw that all the SAU regions are initialised as well. But when I leave the SAU disabled in .ioc, the SAU ENABLE bit is 0 and SAU regions are not initialised. Could someone please explain this? Or am I missing something? Is there any other place where we can configure SAU? @mƎALLEm @Tesla DeLorean 

The STM32CubeIDE uses toolchains from https://developer.arm.com/tools-and-software/open-source-software/developer-tools/gnu-toolchain/gnu-rm/downloads and the version it uses is 7.I'd like to use some C++17 features which are not available with gcc7.How can I add a custom toolchain to the IDE? Is there an easy way? Is there a way to get updates or alternatives to achieve my goal?Regards,Marcel

Hi Gents,Something weird is going on my computer since a long while, but it gets very annoying as I work with more on this computer. If I open a .ioc file, or do anything in STM32CubeIDE that will bring up a non-eclypse dialog, the GUI misbehaves in a very weird way. Best example is if I go to Software Packs -> Select Components menu - it becames absolutely unusable, every time I open it up. I attached a file where you can see, how the window looks like after scrolling the list or open up a dropdown item.This happens, when e.g.Working with .ioc files, especially its dialogs, but sometimes in the pinout and clock configuration tabs tooSelect Components dialogThis doesn't happens when e.g.Opening project properties windowIn the Target SelectorNote, that eclypse dialogs, even if contain "ST elements" like drop-downs, text fields, etc, does not produce this error. If a dialog is fully ST based, this happens.Also, I tried the followings:Re-install STM32CubeIDE - no resolutionInstall an o

Hi all,I'm using application note AN4636 for LC sensor.I tested with the example source code, and they work well for one sensor.But when I use multiple sensors, I face an issue. If I use the same value for inductor and capacitor for each sensor, the oscillators between these sensors are affected, the amplitude decrease and the shape change.I can avoid this issue by adjusting the value of inductors to create difference oscillator frequencies, but I think it is not good solution to ensure the stable and consistency of product.Can anyone give me advice to solve this problem?I appreciate this help. Thanks!  

I am working on STM32F407ZET6 with DMA+SPI in slave mode. Trying to reset DMA Counter when NSS is high to avoid shifted data transmit.TX and RX DMA are working on Circular mode.This is my tx data typedef struct { uint8_t InputState[4]; uint8_t reserved1[4]; uint8_t reserved2[4]; uint8_t reserved3[4]; } SyncDataTX;  Inside init function, i did *((uint32_t*)(txData.InputState)) = 0x11121314; *((uint32_t*)(txData.reserved1)) = 0x15161718; *((uint32_t*)(txData.reserved2)) = 0x19202122; *((uint32_t*)(txData.reserved3)) = 0x23242526; HAL_SPI_TransmitReceive_DMA(&hspi1, (uint8_t *)&txData, (uint8_t *)&rxData, sizeof(txData)); Inside interrupt function, i did __HAL_DMA_DISABLE(&hdma_spi1_rx); __HAL_DMA_DISABLE(&hdma_spi1_tx); __HAL_DMA_SET_COUNTER(&hdma_spi1_rx,sizeof(SyncDataTX)); __HAL_DMA_SET_COUNTER(&hdma_spi1_tx,sizeof(SyncDataTX)); __HAL_DMA_ENABLE(&hdma_spi1_rx); __HAL_DMA_ENABLE(&hdma_spi1_tx); In the first tran

(1) Are there any experience for a data exchange via bluetooth between two STM32WB1MMC-parts? (2) How can I use a STM32WB1MMC together with a STM32F411 board? Are there any experiences? (3) How can I create a data exchange between two STM32WB1MMC? (4) Are there documentations, tutorials or further sources?   It is my first use of STM32WB1MMC...   Thank you in advance.

Hi,I have designed a circuit with the LSM6SDOX.It is operating via the I2C BUS and the Gyroscope and Accelerometer are sending data. I have also managed to configure Single and Double Tap detection, however it is the tap detection where I have an issue.When I single tap, it works and triggers INT1 on the Microcontroller, when I double tap, it also works and triggers INT2, however the double tap also triggers the single tap at the same time.The registers are configured as follows in the function below.Please see a screen capture from my Oscilloscope attached. Yellow is the Single Tap, while Blue is the Double Tap. Hopefully it will be self explanatory.Can anyone point me in the right direction on how I stop INT1 from triggering when INT2 is detected?Thanks.  /*-----------------------------------------------------------------*/void configureRegisters() { // Set FUNC_CFG_ACCESS and PIN_CTRL registerswriteRegister(LSM6DSOX_ADDRESS, FUNC_CFG_ACCESS, B00000000);writeRegister(LSM6DS

i am sorry for creating a lot of post recently but i just can not program my microcontrollers. when ever i try to program it i get this:STMicroelectronics ST-LINK GDB server. Version 7.5.0Copyright (c) 2023, STMicroelectronics. All rights reserved. Starting server with the following options:Persistent Mode : DisabledLogging Level : 1Listen Port Number : 61234Status Refresh Delay : 15sVerbose Mode : DisabledSWD Debug : EnabledInitWhile : Enabled Target no device found Error in initializing ST-LINK device.Reason: No device found on target. i have a stlink v3 mini and 3 stm32c031g4u6 microcontrollers soldered to proper breakout boards.i have SWD interface soldered from the edge connector because i had no luck with cn4. SWDIO, SWCLK and RESET are connected. i also have an led soldered to power pins to be sure its powered.i am sure of the soldering job.on my first post someone recommeded i solder capasitors so i did that still no result.i am using linux mint's