Solved

Hello,For our battery-powered smoke extraction fans, we want to develop a brushless motor driver 1.5KW.For this new development we use the reference STSPIN32G4.I use a custom EVSPIN32G4 circuit board with a 4 pole pairs brushless motor equipped with hall sensors.I use MC workbench 6.2.1 for the application.We have a product who work fine with the software configuration in hall sensors.Today we want to migrate this application (fan application) in sensorless mode. in sensorless mode, I am encountering some difficulties:About 1 in 20 starts goes wrong and ends up with a speed fedback error, the other 19 starts happen normally. I would like to have advice on finding the right setting knowing that I have already followed your recommendations in your various supports. I have tested : different value for the regulator settings, different value for Pll ki and G2 value. Here is a description of the malfunction: Each time the speed feedback error appears, the propeller of my fan is st

Hey, i am developing a RFID reader for ISO-14443-4 card with st25r3917b. The firmware is done and works with my custom MCU board connected with external RF board of STEVAL-25R3916B. However , if I switching the testboard and connect with my custom RFID board ,the reader just can not detect the card .It is obviously cause by wrong matching circuit I draw before.The antenna parameter to the Antenna matching tool is still a question for me to implement a custom antenna for the project.Due to lacking of newwork analyzer and imformation from the antenna datasheet. Some of the parameter from the Antenna Matching tool is still missing(Target Q , Targeting Matching Z, Parallel resistance and the present box?). Should i just enter some general numbers in the blank? In my test , there are three board , one main board only contain MCU(STM32L452CCU6), one STEVAL-25R3916B RF board and one custom st25r3917b board contain RFID antenna with cable(FXR.01.07.0100C.A). In the Antenna Matching tool ,

Hi,I am not able to send data/attachment with my messages. I see this: Instead of this:I tried different web browsers but no good.Any idea ?Thank youFerro 

Hello,I am using X-NUCLEO-NFC08A1(ST25R3916B) with Dialog DA14706 MCU , ported the X-CUBE-NFC6 library and first tested for SPI , and it has worked fine(getting Tag UID) . Then i have done some modifications in hardware (Pull-up resistors 1.6K , Made i2c_en high, solder bridges) as well as in Software (defined the macro RFAL_USE_I2C). Still can't get tag UID. By the way ,both Timer tests , antenna RF field (13.56MHz) and chip id (0x31) , all are checked, found correct.Thanks for your help

How get lowest sleep current in STM32F7508-DK?How can I get these current values using RTC?

Hi,I would like to know if it's possible to use M95P32 in memory mapped mode on STM32G474 QSPI interface.Thank you.             Andrea

I want to save a text file to the SD card with the STM32F7508-DK Card, but the code gets stuck during the formatting process of the SD card.Can you help me how to solve this problem?The code line is as follows.  /* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * Copyright (c) 2024 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* USER CODE END Header */ /* Includes ------------------------------------------------------------------*/ #include "main.h" #include "fatfs.h" /* Private inclu

Hi all, We have integrated an LIS2MDL magnetometer into our custom PCB. We have recently been running some tests on the boards, and are collection raw data from the sensor via the I2C line. In our testing, we have found that different boards appear to be outputting different raw values in what should be the same conditions. What we have done is taken the raw data from the devices, calculated the magnitude ( sqrt(mag_x^2 + mag_y^2 + mag_z^2) ) which provides the following pieces of information. All devices are placed in the exact same location in the exact same orientation when the data is recorded. Values are in LSBs, where 1LSB = 1.5 mG: DeviceX DirectionY DirectionZ Direction Magnitude# 1-3-15358163# 2126-218454519# 3132-315211404# 4262-376325561 We have been testing the devices with various paramagnetic and ferromagnetic materials, so I'm wondering if there was some sort of bias introduced that I am unaware of. Regardless, I am looking for some explanation a

Hi,We have now a problem with some boards, H7A3ZI or H743ZI , when switching off :   RTC stops working !RTC is powered on VBAT with a standard CR2032 and was working as it should on about 500 boards since more than a year. Now (some) batteries loosing voltage and we get errors, because RTC no more working.This happend at first at about 2,7V (cell voltage), now even on new boards with 3,0V cells.The problem starts at the moment of power off, when VDD falling (to 2V or so) , the internal switch going to use the VBAT as supply for RTC and backup ram. On affected boards is about 5 ms (!) long the LSE oscillation away, then starting (on VBAT supplied now) again - or no more, showing the error on next startup.Is there anything we can do, to avoid this ? Or is there some "known problem" with the H7 series, when switching to VBAT ?   (In errata i found nothing about this problem.)

Hi,i have a scrollable container with some objects inside:on the left and right i have these images:       i need to hide the images images on left and right border according to scroll position and number of objects:if objects are <= 6 hide left and right imagesif objects > 6 and scroll is full right hide left and show rightif objects > 6 and scroll is full left show left and hide rightif objects > 6 and scroll is on middle show left and rightAny suggestion?

Why does ST not provide a spice model for a new opamp. Specifically the TSB182 ?New parts should have a model.No model , not going to be considered  for use.On  another note  ST's website is almost unusable. I get HTTP 408 and 504 errors almost everywhere I go , very frustrating.

I have my OCTOSPI1 as QSPI working - in "indirect mode", now using DMA: it generates a very clean waveform (no gaps between words or bytes as in "polling mode", a smooth waveform).I use also OCTOSPI1 as a "regular SPI transmitter" (acting as SPI Tx). But due to fact that OCTOSPI is NOT a "regular SPI" (it is NOT "full-duplex"): I use SPI3 as a SPI Slave RX:I connect QSPI SCLK with SPI3 SCLK and SPI3 MOSI is QSPI DIO1 (as MISO). Now I have shared pins for QSPI and a regular SPI on the same QSPI pins. I works.I use also SPI3 Rx DMA. It makes the SPI waveform way better (no gaps).The project is here (if you want to see how to use DMA for OCTOSPI as QSPI and SPI3 as Slave Rx for regular SPI):https://github.com/tjaekel/NUCLEO-U5A5JZ-Q_QSPI What I have realized:Callback comes way to earlyBut it is obvious for me.Thevoid HAL_OSPI_TxHalfCpltCallback(OSPI_HandleTypeDef *hospi)comes when the DMA has finished to push Tx words into QSPI FIFO.But it does not mean the transaction has really fin

1. Yesterday I downloaded CubeIDE 1.14.0 for Linux Mint Cinnamon 21.22. Today I installed it and I tried to run it from the graphical app launcher3. It asked me for the workspace's name. I gave it a one. This window was closed4. Nothing happen, really, nothing!5. I tried to re-run it and it asked me for the workspace's name. Then it said there was a workspace active with the same name6. I run it from command line:$ /opt/st/stm32cubeide_1.14.0/stm32cubeide_wayland %F7. It asked me for the workspace's name. Then it said there was a workspace active with the same name8. I opened the app manager and there were 3 open Java instances plus some CubeIDE apps. I killed them all9. I run it from command line (again):$ /opt/st/stm32cubeide_1.14.0/stm32cubeide_wayland %F  10. The IDE finally started. I haven't gone further at this moment. I just want you to know this misbehavior Why this horrible and awkward behavior? It's the lastest release! Same happened with previous releases.&nb

I'm trying to define a region of RAM for storing debug information that can persist following a reset (DEBUG_RAM). I'd like to put variables in a section (.debug_ram) that are stored in the DEBUG_RAM memory such its usage properly displays in the Build Analyzer.When I do this my elf and hex files are a normal size, 1.3MB and 15kB respectively. My bin files, however, are 393MB. Unfortunately the company I work for has standardized on bin files, particularly for their bootloader software.I have attached my modified linker file (renamed STM32F765VITX_FLASH.ld.c so that it can be attached to the forum) and main.c where I locate the debug_ram_test variable in the in the .debug_ram section. When I build the build analyzer window correctly shows that 6.25% of the DEBUG_RAM region is used.If I use a bin-to-hex utility to convert the bin file I see it's almost all data records with all of the data equal to zero, interspersed with Extended Linear Address records outside the range for t

Hi, I wonder if someone can recommend an alternative to STM32H563ZIT6 mcu for minimum 11 Uart peripherals ona single IC. Preferably if the IC is from the STM32F series.NOTE: The above quantity achieved by treating the USART ports as UART using 144 pins STM32H563Thank youSAM 

Hi ,I am using an STM32F205 for my project. We were using HSI as the clock source before and found out that HSI will not work very well with high temperatures for UARTs, So we added an External crystal clock (16Mhz) but I am unable to get Comms out of UARTs now (There are some random values coming through uart sometimes). This is my clock configRCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; RCC_OscInitStruct.HSEState = RCC_HSE_ON; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; RCC_OscInitStruct.PLL.PLLM = 14; RCC_OscInitStruct.PLL.PLLN = 240; RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; RCC_OscInitStruct.PLL.PLLQ = 4; if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { Error_Handler(); } RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; RCC_ClkInitStruct

I have done following configuration for RTC:static void MX_RTC_Init(void){/* USER CODE BEGIN RTC_Init 0 *//* USER CODE END RTC_Init 0 *//* USER CODE BEGIN RTC_Init 1 *//* USER CODE END RTC_Init 1 *//** Initialize RTC Only*/hrtc.Instance = RTC;hrtc.Init.HourFormat = RTC_HOURFORMAT_24;hrtc.Init.AsynchPrediv = CFG_RTC_ASYNCH_PRESCALER;hrtc.Init.SynchPrediv = CFG_RTC_SYNCH_PRESCALER;hrtc.Init.OutPut = RTC_OUTPUT_DISABLE;hrtc.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;hrtc.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;hrtc.Init.OutPutRemap = RTC_OUTPUT_REMAP_NONE;if (HAL_RTC_Init(&hrtc) != HAL_OK){Error_Handler();}/* USER CODE BEGIN RTC_Init 2 *//* USER CODE END RTC_Init 2 */}With prescalers set as:#define CFG_RTC_ASYNCH_PRESCALER (0X7F)#define CFG_RTC_SYNCH_PRESCALER (0XFF) The system is clocked with 32 MHz HSE.I configured timer server to have periodic wakeups every 10 mins:HW_TS_Create(CFG_TIM_PROC_ID_ISR, &Wakeup_mgr_Id, hw_ts_Repeated, Set_Wakeup_Task);HW_TS_Start(Wakeup

We are using Timer3 to increment a uint64_t counter for serial port operation and need to be able to grab the counter value in the main loop.  //---------------------------------------------------------------- // -------------- Timer 3 ---------------------------------------- //---------------------------------------------------------------- // Setup for timer 3, set defaults uint32_t tim_prescaler = 0; uint32_t tim_period = 0; uint32_t TimOutClock = 1; // Timer 3 configuration. We want a timer 3 frequency of 2Khz(a interrupt // every .5msec tim_prescaler = 0; TimOutClock = SystemCoreClock/1; tim_period = __LL_TIM_CALC_ARR(TimOutClock, tim_prescaler, 2000); TIM_TimeBaseStructure.Prescaler = tim_prescaler; TIM_TimeBaseStructure.CounterMode = LL_TIM_COUNTERMODE_UP; TIM_TimeBaseStructure.Autoreload = tim_period; TIM_TimeBaseStructure.ClockDivision = LL_TIM_CLOCKDIVISION_DIV1; TIM_TimeBaseStructure.RepetitionCounter = 0; LL_TIM_Init(TIM3, &TIM_TimeBaseStruc

Hello, I've to add the x-cube-cryptolib to our application. I added to include path, the file cmox_low_level.c and the library file libSTM32Cryptographic_CM3.a. I get these errors: \Middlewares\ST\STM32_Cryptographic\lib\libSTM32Cryptographic_CM3.a(1): error: A1167E: Invalid line start\Middlewares\ST\STM32_Cryptographic\lib\libSTM32Cryptographic_CM3.a(2): error: A1167E: Invalid line start\Middlewares\ST\STM32_Cryptographic\lib\libSTM32Cryptographic_CM3.a(3): error: A1167E: Invalid line start\Middlewares\ST\STM32_Cryptographic\lib\libSTM32Cryptographic_CM3.a(4): warning: A1313W: Missing END directive at end of file   What can I do to fix these errors? Thanks in advance!  

Hi, Could you provide me the MTBF or FIT value of M24C02-FDW6TP. 

There's a lot of "information" posts appearing; eg,https://community.st.com/t5/stm32-mcus/how-to-obtain-and-use-the-stm32-96-bit-uid/ta-p/621443This is all very good & useful but, in the activity listing, they are indistinguishable from user questions:It would be useful if these were clearly differentiated.

I am working with standby mode on the STM32F7508-DK board and measuring the standby current as 900mA. The tools I use in the program consist of LED and RTC for wake-up. What should I do to reduce this current? 

As I wrote in the subject, Upgrading STM32CubeMX from version 6.6.1 to 6.7.0 The SDCARD stops working.During mounting :  fr=f_mount(&FatFs,"/",1);  if(fr==FR_OK)  {    ...   .... }returns "FR_NOT_READY"The micro is an STM32F4, I use SDIO in SD 4 bits Wide bus mode and it has always worked fine.RegardsDomenico

Hi, I'd like to use a code from javascript in the STM32F746 DISCO. It's a radar that receives data from an ultrasonic sensor. The code for the radar was made using processing and I want to show it in the STM screen but I got no idea.Here is the code from javascript and a view of the radar.import processing.serial.*; // imports library for serial communication import java.awt.event.KeyEvent; // imports library for reading the data from the serial port import java.io.IOException; Serial myPort; // defines Object Serial // defubes variables String angle=""; String distance=""; String data=""; String noObject; float pixsDistance; int iAngle, iDistance; int index1=0; int index2=0; PFont orcFont; void setup() { size (1200, 700); // ***CHANGE THIS TO YOUR SCREEN RESOLUTION*** smooth(); myPort = new Serial(this,"COM3", 9600); // starts the serial communication myPort.bufferUntil('.'); // reads the data from the serial port up to the character '.'. So actually it reads this: angle,distance. }

Good morning, I have to do a porting from a project developed on STM32F423 to an STM32U5A5The starting project used the wiced sdk, with the supported platform STM32F423.If I understand well, for STM32U5A the wiced sdk is deprecated, and it would be better to use the package Infineon.AIROC-Wi-Fi.Bluetooth-STM32. Is it correct? Is there any application note to help me to do the porting? or to use the infineon package with STM32CubeMx?