Solved

Posted on August 01, 2017 at 11:47Dear community,I read on the SPBT2632C2A page here: http://www.st.com/en/wireless-connectivity/spbt2632c2a.html that this IC is NRND.Is there a standard replacement part that would fit my needs i.e. using the SPP easily. Thanks !#bluetooth #spbt2632c2a #spp

Posted on August 02, 2017 at 16:16Hi,Does anyone know where I can find the IAP_main example with SD card?This example is mentioned in the document 'In-application programming with SD cards' (AN4854)but I couldn't find the example itself, only the one with UART.Thanks in advance

Posted on August 02, 2017 at 19:41I am using STM32F429 discovery board.I am trying to generate pwm output on pin 11 of GPIO G. I have set and enabled the corresponding registers and bits but there is no output on pin 11. If I write a simple delay code then pin 11 does go high and the code works fine. I am coding using direct registers. Any suggestions?&sharpinclude <stm32f4xx.h>void clk_sys(){ RCC ->CFGR |= RCC_CFGR_MCO1_0; RCC ->CFGR |= RCC_CFGR_MCO1_1; RCC ->CR |= RCC_CR_PLLON; RCC ->APB1ENR |= RCC_APB1ENR_TIM2EN;}void enable_gpio()//setting pin 11 of port g for AF1 which corresponds to timer 2.{ RCC ->AHB1ENR |= RCC_AHB1ENR_GPIOGEN; //Enables port G input output pins by setting the corresponding bit in advanced high performance bus 1 register. GPIOG ->MODER |= GPIO_MODER_MODER11_1; //Configures pin 11 for alternate function mode by setting the corresponding bit in the mode register GPIOG ->OTYPER &= ~(GPIO_OTYPER_OT_11); //Makes the output type as

Posted on December 28, 2016 at 16:44I found seriously bug on CubeF7 v1.5.0/v1.5.xBug found at ./STM32Cube_FW_F7_V1.5.0/Middlewares/ST/STM32_USB_Device_Library/Class/MSC/Inc/usbd_msc.hdiff -urN b/usbd_msc.h a/usbd_msc.h--- b/usbd_msc.h 2016-09-14 17:48:24 +0900+++ a/usbd_msc.h 2016-12-29 00:37:02 +0900@@ -101,7 +101,7 @@ uint16_t scsi_blk_size; uint32_t scsi_blk_nbr;- uint32_t scsi_blk_addr;+ uint64_t scsi_blk_addr; uint32_t scsi_blk_len; } USBD_MSC_BOT_HandleTypeDef;'scsi_blk_addr' is also used sector-to-byte address exchange calcuration.But that causes data corruption above 4GB address datas.I found this bug when implementing USB-SDCard Reader on STM32F746G-Discovery.I suspect that exists similar bug on USB-Libraries.Please fix this bug until next release.Best regards,Nemui.

Posted on July 31, 2017 at 14:41Beginner working with STM32L452:I have TIM2 set up as encoder-based timer. Works perfect.Now I want an interrupt whenever the TIM2 reaches a certain value (position).I tried to enable timer interrupt through HAL_TIM_Encoder_Start_IT, and hoped to be able to get an interrupt when the encoder passed value 0. But I only managed to get an interrupt on every single encoder tick.Reading a bit more on timers, i wonder if setting up another timer as slave to TIM2 would be the way forward ?If yes, then how should the master/slave output/input be configured to have the slave follow TIM2 ? I have read the timer overview in 'en.DM00042534.pdf' but I don't understand all of it.if no, what are my options then?If a solution can be achieved through CubeMX configurator, i I would very much appreciate that, but it is not a must.Thanks.#interrupt #timer #hal_tim_encoder_start_it #interrupts #encoder

Posted on August 02, 2017 at 11:42I have a clean slate CubeMX project on a STM32F401C-Discovery board. I have set up the onboard Cirrus audio DAC, and send a hard-coded test signal to it via DMA-driven I2S. I can hear the sound, but it is at wrong frequency. The 2kHz test signal, and the i2s-3 is set to 48kHz samplerate, but depending on how I configure the PLL, I hear 122Hz, 180Hz or 244Hz audio. I have confirmed with a logic analyzer that the I2S protocol runs too slow. The only things I have changed from the CubeMX generated template project is: enable i2c-1 (communication with the DAC, this works)enable i2s-3configure i2s-3 to have a cyclic DMA, 48kHz, 16bits on 32bit dataframeIn the source code, I only initialize the DAC and enable the DMA. No other changes to the generated source are done.The three configurations I tried with: PLLM=4 gives a I2S WS (frame clock) of 2.93kHz, and the 2kHz audio is at 122Hz:With PLLM=6, I see a WS of 4.4kHz, and audio at 184Hz:And with PLLM=8, WS i

Posted on April 27, 2017 at 21:34SPWF04SCMQTT Unable to connect to any MQTT ServerAccordinghttp://www.st.com/content/ccc/resource/technical/document/user_manual/group0/69/bf/26/08/53/62/49/af/DM00329655/files/DM00329655.pdf/jcr:content/translations/en.DM00329655.pdf UM2114 User manualIn Section 6.54AT+S.MQTTCONN=test.mosquitto.org,,,,,,,,,,, AT-S.ERROR:111:Request failed+WIND:87:MQTT Closed:0:0+WIND:87:MQTT Closed:0:0I have also test other mqtt server broker.hivemq.comAT+S.MQTTCONN=broker.hivemq.com,,,,,,,,,,,AT-S.ERROR:111:Request failed+WIND:87:MQTT Closed:0:0+WIND:87:MQTT Closed:0:0The module have internet connectionAT+S.PING=5,,test.mosquitto.orgAT-S.Start:37.187.106.16AT-S.Reply:56:111AT-S.Reply:56:111AT-S.Reply:56:111AT-S.Reply:56:111AT-S.Reply:56:112AT-S.Stop:0:111AT-S.OKAnd i have test successfully the insecure and secure connection with computer software client MQTT.fx on port 1883 on both serversbroker.hivemq.comtest.mosquitto.orgI have test also with ips instead of hos

Posted on August 01, 2017 at 13:43I am using lps22HB and connected it to edison through I2C interface.Env:I am using mraa and node JS.This is how I configured the sensor        i2cBus.writeReg(INTERRUPT_CFG, AUTOZERO | DIFF_EN | PHE | PLE);        i2cBus.writeReg(THS_P_L, (THS_P & 0xFF));        i2cBus.writeReg(THS_P_H, (THS_P>>8) & 0xFF);In the above code, I am using Differential threshold of pressure low and pressure high events.With this setup, when I poll for an differential pressure interrupt on INT_SOURCE register, I am able to accurately catch pressure low and pressure high events.But I dont want to do such tight polling..If I change the code to check for the generated interrupt once in every 1 second, it is not working. Somehow the generated interrupt is being cleared off without me reading the INT_SOURCE registerIs there a way to configure the sensor in such a way that

Posted on August 02, 2017 at 06:10Hi.I wonder if I can dynamically change the GPIO configuration of stm32f072.(that is, input to output or output to input)  Regards.

Posted on July 27, 2017 at 12:14Perhaps the title is wrong, but my code behaves like this: I have configured 4 channels to be converted in the ADC; I have put a variable which increments inside ADC irq EOC (EOC_Counter) and another which increments inside ADC irq EOSQ. EOC_Counter 

Posted on July 27, 2017 at 09:55I have a problem with STM32F756 USB CDC (HS with FS PHY) device and core sleeping. I isolated all other code and left only the USB driver and main loop calling WFI instruction. If there is no call to WFI, USB is working properly, but if I call WFI in the main loop, USB stops responding. USB clock is not stopped on entering in sleep. Any advise?#__wfi #stm32f7 #sleep #usb

Posted on July 31, 2017 at 22:35In STM32Cube_FW_F7_V1.7.0/Projects/STM32746G-Discovery/Examples/SPI/SPI_FullDuplex_ComDMA example shows a simple DMA transfer with data cache on.  How can aRxBuffer buffer can be updated correctly without a region defined non-cacheable?

Posted on October 06, 2016 at 16:01  The original post was too long to process during our migration. Please click on the attachment to read the original post.

Posted on July 31, 2017 at 13:36Hi, I am working on my project which requires to send some data over UART.I have F429ZI Nucleo board with a UART2 configured (see uart2_config image). The UART2 has Interrupts enabled so I can use the HAL_UART_Transmit_IT function.I am passing an array of uint8_t values. Only 4 bytes. The bytes are getting transmitted via the TX pin as expected, but only 7 bits per byte are transmitted. (see tx_8_bits_no_parity image).So I got into the F429xx datasheet (http://www.st.com/content/ccc/resource/technical/document/reference_manual/3d/6d/5a/66/b4/99/40/d4/DM00031020.pdf/files/DM00031020.pdf/jcr:content/translations/en.DM00031020.pdf ) and on page 994 the Table 146 clearly states that when the bits M (length = 8bits) and PCE (parity = None) are reset, the UART frame will be: Start Bit, 8 data bits, Stop Bit.Why is MCU sending only 7 bits when no parity is enabled? So I decided to enable parity in CubeMX and set it to Even.However, the parity bit just tak

Posted on August 01, 2017 at 07:37Hi,the Cube MX Version 4.22.0 don't generate the Middleware/ST correct. The folder tree is correct, but not filled with files.I tested with the L475VGT and add the Virtual Com Port.#middleware #cube-mx #usb-cdc #4.22.0

Posted on July 19, 2017 at 16:05Hello everybody,I have some trouble when I want to erase my chip by  sector erase  or mass erase (ST LINK UTILITY with ST LINK dongle)   I obtain  some  dummy bytes after an erase operation like that :00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 3C 29 00 08 29 21 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF BD 3B 00 08 BD 3B 00 08 00 00 00 00 BD 3B 00 08 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF BD 3B 00 08 BD 3B 00 08 00 00 00 00 BD 3B 00 08 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF BD 3B 00 08 BD 3B 00 08 18 08 00 00 BD 3B 00 08 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FFCan I forget something ?Normaly is filled by 0xFF ?When I use this method on a STM32F103 it works well.Of course when I try to put a firmware it become like a random

Posted on August 01, 2017 at 10:32Hello,I am searching for an STM32 device which offers 3 full 12-bit analog watchdogs.I have spent hours navigating on st.com but all I have found was the STMF303 line with 1x 12-bit watchdog + 2x 8-bit watchdogs.Can somebody confirm that there is no such an STM32 device?Thank you in advace,Gahlen#analog-watchdog

Posted on July 31, 2017 at 13:55Hey I use stm32f030p4 and i want counting a external frequency (Learning remote ).I configure timer  and interrupts like thisTIM_ICInitStructure.TIM_Channel = TIM_Channel_1;TIM_ICInitStructure.TIM_ICPolarity = TIM_ICPolarity_Rising;TIM_ICInitStructure.TIM_ICSelection = TIM_ICSelection_DirectTI;TIM_ICInitStructure.TIM_ICPrescaler = TIM_ICPSC_DIV1;TIM_ICInitStructure.TIM_ICFilter = 0x0;TIM_ICInit(TIM3, &TIM_ICInitStructure);/* Enable the CC2 Interrupt Request */TIM_ITConfig(TIM3, TIM_IT_CC1, ENABLE);/* Enable the TIM1 global Interrupt */NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;NVIC_InitStructure.NVIC_IRQChannelPriority = 0;NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;NVIC_Init(&NVIC_InitStructure);uint32_t now =0;void TIM3_IRQHandler(void){if(TIM_GetITStatus(TIM3, TIM_IT_CC1) == SET){TIM_ClearITPendingBit(TIM3,TIM_IT_CC1);now=TIM_GetCapture1(TIM3);}}Interrupt work good but TIM_GetCapture1(TIM3) is always 0 .how can i solve t

Posted on June 07, 2017 at 20:18 Hi guys, I am running into some timing issue using CubeMX, probably after upgrading to the latest version. A couple of weeks ago I noticed my SysTick running roughly twice as fast as expected (half of 1ms) so I changed my 1ms systick to Timer2 which worked fine. Today I turned on my USART3 for the first time at 9600 BAUD and could not get the HyperTerm to receive correctly (all garbage). Then I took a closer look at the signal through the scope and noticed the BAUD was actually at about 23KBAUD, which was weird because I set it in the code as: huart3.Init.BaudRate = 9600; After mucking around I got the HyperTerm to work normally by changing the BAUD setting to: huart3.Init.BaudRate = 4000; // This is actually 9600 BAUD (verified with scope) I have a hunch the BAUD rate issue is related to the SysTick issue.Anyone has this issue or is familiar with CubeMX to give me a clue here? Thanks, ED Note: this post was migrated and contained many thr

Posted on July 31, 2017 at 23:37I'm using CubeMX with the STM32F469IIT and trying to select 32-bit wide SDRAM using the FMC but the options only show 8 or 16-bit.Is this correct? I can't see anything in the reference manual about the LQFP176 not being able to do 32-bits. It works for other 469 chips.Thanks.#cube-mx #fmc

Posted on July 28, 2017 at 18:16in my function, several heap pointers are defined like thiswhen I comment the 111 line. the whole code works well. But when I add this line, the pointer Test_feature, ZeroCenter_Parameters, C1K,C1B will all, or sometimes partly, point to 0x000000.eventually in 2 debug with the same code, it may different.so the Question is:In general, What will let the Heap pointer point to 0x00000? before free.for my observation, the heap size is enough on my project (HEAP SIZE=0x8000, the same as stack size). I'm using STM32F746NG-Discovery Board so the RAM Space(at least 240KB for algorithm) is also enough. So it may be the problem of the IDE or Compiler?My environment:   KeilV523, STM32F746NG-Disco, Win10 Edu.for more general situation. this code.void heaptest(){ int *a; a=(int*)malloc(1024*4); int i=1024; while(i--) { *a=i;//printf(''%d'',*a); a++; }free(a);}0x08004468 BD10      POP    &nb

Posted on April 28, 2017 at 20:51Hello, writing support library for my dev board, and i run into the problem.I have simple txt file generated by Print_SD() function.If this function is called from mains, it does produce TEST.TXT file, no problemsBut if i map this function to GPIO interrupt, and call Print_SD() function from IRQ program, it simply hangs. It looks like it is preventing functions to be executed:void SDIO_IRQHandler(void);void SD_SDIO_DMA_IRQHANDLER(void);How can i fix this ? SDIO does have higher priority, so why it should hang ?void NVIC_Config(void) //SDIO{  NVIC_InitTypeDef NVIC_InitStructure;  /* Configure the NVIC Preemption Priority Bits */  NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);  NVIC_InitStructure.NVIC_IRQChannel = SDIO_IRQn;  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;  NVIC_Init(&NVIC_InitStructu

Posted on July 28, 2017 at 14:40It appears from the (rather lacking) documentation that the DMA Double Buffer Mode is only a Peripheral to Memory transaction. Is this correct? Or can I use double buffering from memory to peripheral?

Posted on July 28, 2017 at 14:50I am trying to use STemWin 532 on a STM32f467 board. I created a framewin with 4 buttons using GuiBuilder and ran the application, but the display is scrambled. This is how a framewin with 4 buttons looks like on my display : https://drive.google.com/open?id=0B-2BPm8Fn6lwVzlfZXEzM29pbG8.I've also attached my 'main.c' and framewin source files. I tried adding an osDelay after GUI_Exec() but it did not work.Any help is greatly appreciated.

Posted on July 30, 2017 at 15:59Playing around with timer/counters, trying to learn things. When I use HAL_TIM_OC_Start_IT, the callback HAL_TIM_OC_DelayElapsedCallback gets called at the appropriate time. The counter continues on happily about its way, and when it rolls over, shouldn't I expect to also get a callback for PeriodElapsed?