Solved

Hi,I’m developing an application on multiple STM32H563 units on the same board. Although all units use the same firmware, the logic depends on each unit’s position, so I need a way to identify which unit it is.Currently, I program the full flash memory (.bin/.elf) with STM32CubeIDE or STM32CubeProgrammer. Is there a standard or recommended way on STM32H563 to store small per-device information (like unit ID or role) separately from the main application flash, so the firmware can read it at startup? Thanks for any guidance!

Hello,I got back to my issues from this post.I was able to connect wires to SPI lines, and get the measurements to logic analyzer. These are the results:Logic2 screenshot Now i can see that the issue is the CS line, but i dont know why it is being changed to HIGH in these short pulses.  The GPIO config: /*Configure GPIO pin : SPI1_CS_Pin */ GPIO_InitStruct.Pin = SPI1_CS_Pin; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(SPI1_CS_GPIO_Port, &GPIO_InitStruct);SPI Config:hspi1.Instance = SPI1; hspi1.Init.Mode = SPI_MODE_MASTER; hspi1.Init.Direction = SPI_DIRECTION_2LINES; hspi1.Init.DataSize = SPI_DATASIZE_8BIT; hspi1.Init.CLKPolarity = SPI_POLARITY_LOW; hspi1.Init.CLKPhase = SPI_PHASE_2EDGE; hspi1.Init.NSS = SPI_NSS_SOFT; hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_32; hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB; hspi1.Init.TIMode = SPI_TIMODE_DISABLE; hspi1.Init.

My goal is to use USART6 as debug output because I haven't route the dedicated BootROM pins of the USART2.Anyway! It seems that the BootROM is trying to read my SD card. First sequence:CMD and CLK of SDMMC1 seems to be talking to the SD card in a very low speed. Here I'm talking about kHz. I don't know what they are saying. The signals are perfectly square waves.Second sequence:Suddenly the CLK become a fast sine wave. I still don't know the frequency, but it's defently much faster than the first sequence. Now, the D0 is a digital input of BootROM. This D0 looks like a sword shaped signal. I don't know if it's my configure at my osciloscope that cause this view.After the second sequence as ended. There are no more data passing between the SD card and MP257. The clock is still running at the same frequency.I don't know if the TF-A firmware has been read or not. I haven't tested the USART6.Question:Where can I find the commands/data that are passing between the SD card and the MP257

Introduction: While testing the U575 with external PSRAM connected over OCTOSPI1, certain memory test scenarios fail deterministically.   Setup: Using a STM32U575, connected on OCTO-SPI1 to PSRAM (IS66WVH8M8) 8MB in size. The STM is configured in memory mapped mode, hyperbus enabled, no DMA or Cache enabled, & wrap/burst mode disabled.   While testing the PSRAM using Barr tests, found that the data bus and address bus test pass, but the device test had a deterministic pass/fail behavior. The device test passed for any size as long as the test wasn't crossing the 2MB boundary.  Base (start) address Size Result 0x9000 0000 2 MB Test passes (also for 0x9020k,0x9040k, 0x9060k resp.) 0x9010 0000 2MB Test fails, around 0x9020 0000.  0x9030 0000, 0x9050 0000 respectively 2MB Test fails, around 0x9040 0000 and 0x90600000 respectively. 0x901FF000 2 kB Test fails around 0x9020 0000.    While debugging/analyzing code found something inter

Hello there,I'm trying to create a project for stm32h7s7 with external loader. But when i added the external loader in IOC file the all indexes were lost in editor mode. But I checked for building, i can't see any problem. I tried index -> rebuild but it could not help me

Hi!I'm working on a Trustzone enabled application in STM32U5A5 nucleo board and have some questions in my mind. I have used the configurations of the example project for the Trustzone, which you can find below: - TZEN=1 - SECWM1_PSTRT=0x0 SECWM1_PEND=0xFF meaning all 128 pages of Bank1 set as secure - SECWM2_PSTRT=0xFF SECWM2_PEND=0x0 meaning no page of Bank2 set as secure, hence Bank2 non-secure I have enabled SAU and left it with the default configuration. I've also enabled the GTZC_S. In my application, I'm using TAMP mechanism of the RTC to create an interrupt when the output signal doesn't match the input signal. First question:My application can boot from the secure app and jump to non-secure app without any problems. But in the MX generated NonSecure_Init() function, after the line SCB_NS->VTOR = VTOR_TABLE_NS_START_ADDRThe SCB->VTOR_NS register doesn't change, remains as 0x0 (according to the SFR in the debug interface). After the boot to non-secure

I have an ILI9341 SPI screen and a small self-made library that can display different numbers on the screen. I want to be able to update the screen (display a new number) every time there is an interrupt. I have tested the screen functions independently, and they work properly. But when I call them from the interrupt handler, they fail. The board is STM32F407G-DISC1. Timer configuration static void MX_TIM2_Init(void) { /* USER CODE BEGIN TIM2_Init 0 */ /* USER CODE END TIM2_Init 0 */ TIM_ClockConfigTypeDef sClockSourceConfig = {0}; TIM_MasterConfigTypeDef sMasterConfig = {0}; /* USER CODE BEGIN TIM2_Init 1 */ /* USER CODE END TIM2_Init 1 */ htim2.Instance = TIM2; htim2.Init.Prescaler = 999; htim2.Init.CounterMode = TIM_COUNTERMODE_UP; htim2.Init.Period = 335900; htim2.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; htim2.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE; if (HAL_TIM_Base_Init(&htim2) != HAL_OK) { Error_Handler(); } sClockSourceConfig.ClockS

Our product is a space device and as a result, we've had to recently do some radiation testing of the device. In particular, focused on the STM32H755 processor that runs the board.I'm looking for any papers/references/app_notes, anything, that can help me to gather details about how the processor performs in a radiation environment.And yes, I realize this is not a rad-hard or rad-tolerant processor. 8-)Thanks.-brad w. 

Hi there !i work with DS2482 I2c to one wire . After i send the command reset i need the read the status register until i find one bit at 1, so i wrote my routine in this way  static uint8_t DS2482_Status_Register(void) { uint8_t register_status=0; uint8_t data=0; while(register_status !=0x02 ) { Master_Recive_Data(DS2482_Addr, &data, 1); // HAL_Delay(1); dato= data; register_status = data; register_status &= 0x02; } if(register_status != 0x02) { return HAL_TIMEOUT; } return HAL_OK; } when i run the program i recive error 4 from i2C formvoid HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c) { } But if in the code below i put one delay of 1ms everything work perfect . So there is one "elegant" way to resolve the problem  ? or there are other solution  ? Thanks a lotSergio

STM32CubeIDE Version: 2.0.0When trying to create a new project from the IOC of another project, I can't find a way to do it. Is this feature lost or BUG ? Thanks in advance.

Hello,   I’m starting a new design with the STM32H755. I also have the dev board (Nucleo-H755ZI-Q), but I do not have its schematic. So far, the closest schematic/design reference I’ve found is Figure 18 in AN4938 (“Getting started with STM32H755”).   Could you please share more schematic references?   I was thinking about the following: The complete NUCLEO-H755ZI-Q schematic and the BOM Any additional pages/details related to the Figure 18 schematic (it appears to reference a multi-page schematic, but we only have the first page in this document) Any other official schematic/reference design examples for STM32H755 that I could use as a starting point   Thank you for your time and help!  

I am working on STM32N6570-DK board. I am trying to run a code for three channels ADC+DMA, INP8, INP10, INP16. The output at USART is coming out to be zero in all three channels. I am attaching the code here. 

I have a project for a battery-powered clock using the STM32WBA55 chip. The battery is replaceable; the device can sit unused on a shelf for up to 4 months without the battery. Since the STM32WBA55 doesn't have VBAT or VRTC pins, how can I keep the backup recorder, time, and date active?

After updating and restarting my PC with Windows 10, my old version of CubeProgrammer would not open at all. The version number is unknown. Other STM32 software works without any issue such as CubeMX and CubeIDE.I then tried installing the latest version, 2.21.0. The program launched (even when run as administrator), but it did not function fully. I attached a screenshot for reference. None of the four icons on the top-left responded, and I received error messages when clicking the icons on the right.I also tried installing previous versions from 2.16.0 to 2.20.0, but none of them worked. Specifically:Versions 2.16.0, 2.18.0, and 2.19.0 briefly showed the launch logo, then closed immediately.Versions 2.20.0 and 2.21.0 would open, but the program remained unusable. 

Hi everyone,I am bringing up a custom board based on the STM32H743VIT6. I am trying to connect via ST-Link (SWD), but I am getting the standard "Can not connect to target" error in STM32CubeProgrammer.The Setup:MCU: STM32H743VIT6Debugger: ST-LinkInterface: SWD (SWDIO, SWCLK, GND, 3.3V detected)Power Supply: External 3.3V. Board voltage source to provide the necessary power for the system, something that ST-Link alone cannot do.The Problem: After failing to connect, I probed the power pins and found abnormal values:VCAP Pin: I measured 2.7 V on the VCAP pin. As I understand it, VCAP corresponds to the internal LDO output for VCORE and should normally be around 1.2 V. Does a reading of 2.7 V indicate an internal short circuit to VDD or a blown LDO?VDD Drop (Pin 75): On Pin 75 (VDD input), I have a known bad solder connection (trace compromised). I measured 2.3V on this pin.Question: Since the other VDD pins are correctly supplied with 3.3V, shouldn't the internal silicon power mesh maint

My STM32H533VE works as PD Sink.We connected CC1/CC2 with DBCC1/DBCC2 (as AN5225), STM32 cannot power up with a USB PD adapter. The adapter supplies power for ~20ms then stops the supplying.If I remove the long time initialization code (LSE initialization), system can boot up and USB PD works fine (PDO can switch).Is this normal? if yes, I may move the LSE initialization later.

Hi everyone,I’m feeling a bit defeated by a task that should be "Hello World" level simple. I’m trying to get a basic printf to show up in PuTTY using a NUCLEO-G474RE, but I’m getting absolutely nothing in the terminal.I do this all the time with my NUCLEO-H723ZG using USART3 and it works like a charm. For the G4, I’ve switched over to USART2, but no luck.Here is my setup:Toolchain: CubeMX + CMake.The Logic: I've overwritten __io_putchar() with a HAL_UART_Transmit call.The Config: USART2 is enabled, baud rate matches PuTTY (115200), and the clocks seem fine.I even had a friend who uses G4 boards regularly take a look, and even he couldn't figure out why the data isn't hitting the ST-Link. It feels like I'm missing one tiny, G4-specific checkbox or jumper setting.I've put together a bare-bones repository with just the code for the printf here: https://github.com/mpek29/nucleoG4Has anyone else run into similar issues ?Thanks in advance for any pointers, I'm sure it's something silly I've

See:https://community.st.com/t5/stm32-mcus-boards-and-hardware/struggling-with-a-simple-uart-printf-on-nucleo-g474re-works-on/m-p/874056/highlight/true#M29428 Sidekick says UART2, but the User Manual & Schematics show LPUART1 (default) or UART1 (by changing solder bridges):UM screenshot: https://community.st.com/t5/stm32-mcus-boards-and-hardware/struggling-with-a-simple-uart-printf-on-nucleo-g474re-works-on/m-p/874047/highlight/true#M29425Schematic screenshots - by @mƎALLEm:https://community.st.com/t5/stm32-mcus-boards-and-hardware/struggling-with-a-simple-uart-printf-on-nucleo-g474re-works-on/m-p/874051/highlight/true#M29427 

Hello everyone,I am developing an iOS application using the ST25SDK (converted/wrapped for Swift) to interface with the M24LR16E-R Dynamic NFC Tag.I am facing a blocking issue where any attempt to call readBytes() (which is used in TagReadMemoryGenViewController.readMemoryContent) throws a ComStSt25sdkSTException with error code BAD_PARAMETER.The Setup:Chip: M24LR16E-R (IC Ref: 0x4E)Platform: iOS (Swift) using CoreNFCLibrary: ST25SDK for iOSThe Problem: Upon investigation, the root cause appears to be that the ST25SDK mTag.getMemSizeInBytes() returns a memory size of 0 bytes. Consequently, when readBytes() is called, the SDK performs an internal safety check: if (address + length > mMemSizeInBytes) { throw BAD_PARAMETER; } Since mMemSizeInBytes is 0, this check always fails.Root Cause Analysis: The issue seems to originate in the iOSRFReaderInterface during the Get System Info command. The M24LR16E-R has 512 blocks (2048 bytes total). When using CoreNFC's native getSystemI

Hello, I am currently evaluating the STM32N6570-DK and am seeking clarification regarding a discrepancy I’ve encountered. I can confirm that there is a 48MHz crystal on board for the HSE. However, the default CubeMX projects generated by the board selector, as well as other example projects I have reviewed, all configure the input frequency to 24MHz. Could you please clarify what the correct input frequency for the HSE should be on this discovery kit? Thank you for your assistance.

It's been sat there "thinking" for several minutes now!Just putting "NUCLEO-G474RE VCP" did get an answer

I've designed a custom board and, I'm writing my own firmware that controls STPMIC.While writing a general-purpose driver library to enable future use in other hobby projects, I ran into a few questions.my own general-purpose driver library is: https://github.com/jay94ks/stpmic 1. MAIN vs. ALTERNATIVE.Does this switch automatically based on low-power requirements, or is it something that needs to be configured separately? Or is it the same behavior, but can one side be used for low-power operation when needed?The PWRCTRL_EN and PWRCTRL polarity bits are described as being used to switch between these two modes. If so, is it possible to switch between these modes solely through software, without any physical pins? 2. How many times can I program the NVM?I placed an order with JLCPCB while designing my hobby project board, but they only had the APQR STPMIC1 in stock, so I couldn't order the CPQR. So, I decided to program the NVM. Is there a limit to the number of times I c

Hello,I am using NUCLEO-H755ZI-Q (STM32H755) and I am observing a reproducible boot issue related to high system clock frequency.1. Hardware / EnvironmentBoard: NUCLEO-H755ZI-QMCU: STM32H755Power supply: USB (on-board)Debugger: ST-LINK (Connect under Reset)Supply configuration: LDOToolchain: STM32CubeIDE 1.19.02. Issue DescriptionWhen the system clock is configured to 480 MHz, the board fails to boot after power-on or reset.Flash programming and verification succeedImmediately after reset release, the target becomes unresponsiveST-LINK connection is lost When the same firmware is configured to 400 MHz, the board boots and runs normally.Interesting behavior:Power-on the boardFlash firmware configured for 400 MHz → boots normallyWithout removing power, rebuild and flash firmware configured for 480 MHzThe board runs normally at 480 MHzIf power is removed and re-applied, 480 MHz boot fails againThis behavior is fully reproducible.3. ObservationsThe issue only occurs after a cold power

I have a custom board with stm32wba65 processor. I also have an RFM95 LoRa module. I need to add LoRaWAN capability. I tried adding I-CUBE-LRWAN into my CubeMX but was not able to load it (not a recognised package).How can I get an ST or Semtech approved LoRaWAN stack into my project?Please do not suggest I use stm32WL processor.

Hello STM Community,I currently have a NUCLEO-U575ZI-Q board and the X-NUCLEO-IKS4A1 motion MEMS and environmental sensor expansion board. I’m looking to add BLE functionality and was considering the X-NUCLEO-WB05KN1.Before proceeding, I’d like to ask:Are the X-NUCLEO-IKS4A1 and X-NUCLEO-WB05KN1 compatible when stacked together on the NUCLEO-U575ZI-Q?If not, is there an alternative BLE expansion board that is known to work well with the IKS4A1 on this Nucleo board?Alternatively, is there an expansion or adapter board that allows both shields to be connected without pin conflicts?Any guidance or shared experience would be greatly appreciated!Thanks in advance.