Solved

Hello everyone, I'm working on a BLDC motor project that drives an overhead (tilting) door using the STDRIVE101 gate driver, configured via MC Workbench.The power stage uses STL110N10F7 MOSFETs, and the motor supply voltage is 24V.PWM switching frequency is set to 20 kHz. :collision: Issue I'm facing unexpected triggering of the VDS (Short Circuit) protection, especially: Right at motor startup When I disable and then re-enable the VDS protection while the motor is running, the fault is immediately triggered :gear: Current configuration: VSCREF = 1.32 V → so VDSth = 1.32 V Digital Filter Duration = 111.11 ns SW Dead-time = 800 ns Charge Boot Capacitor = 10 ms / Duty = 0% PWM frequency = 20 kHz MOSFETs: STL110N10F7 Startup current: around 5 A DT/Mode pin is tied to GND → meaning fixed internal dead-time is selected (per datasheet) CP pin is also tied to GND → bootstrap auto-recharge is disabled I also measured that the FAULT signal remains active for ~10 ms aft

Hi everyone,I'm currently working with the ST25R3916B NFC reader IC and I have a few questions regarding the XTI and XTO pins as well as the MCU_CLK output.From the datasheet, I understand that:XTI is the input and XTO is the output of the internal crystal oscillator circuit.The oscillator is designed to operate with a 27.12 MHz external crystal.Now, here’s what I’d like to confirm:Is the external 27.12 MHz crystal absolutely required for normal operation, or is there an internal oscillator that can be used as a fallback?Regarding the MCU_CLK output: this seems to be a clock signal derived from the oscillator.Is this optional?It is used to clock an external microcontroller (e.g. STM32)? Do I have to use it? Many STM32 MCUs already have decent internal oscillators.Are there any recommended crystal components (specific part numbers or manufacturers) that are known to work well with this IC?Any clarification or insights from those with experience using the ST25R3916B would be greatly appr

I am using custom STM32G4 board and generated code using the MCSDK 6.2.0. I am observing that the SysTick_Handler(void) function is called before the peripheral initializations, and it is leading to hardware fault.int main(void) { /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ /* MCU Configuration--------------------------------------------------------*/ /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ HAL_Init(); /* USER CODE BEGIN Init */ /* USER CODE END Init */ /* Configure the system clock */ SystemClock_Config(); /* USER CODE BEGIN SysInit */ /* USER CODE END SysInit */ /* Initialize all configured peripherals */ MX_GPIO_Init(); MX_ADC1_Init(); MX_ADC2_Init(); #ifdef DACENABLED MX_DAC1_Init(); #endif MX_CORDIC_Init(); MX_OPAMP1_Init(); MX_OPAMP2_Init(); MX_OPAMP3_Init(); MX_TIM1_Init(); MX_TIM4_Init(); MX_FDCAN1_Init(); /* USER CODE BEGIN 2 */ MX_MotorControl_Init(); /* Initialize interrupts */ MX_NVIC_Ini

Hello, I'm using STEVAL-SMARTAG2. In the future I want to design my own PCB with  ST25DV64KC and STM32L4P5-CGU6. But for now I want to create my own program and try it on STEVAL-SMARTAG2.If I import example project in CubeIDE and complie it, It works fine.If I want to create my own project and include libraries I get an errors during compiling.So, I did the following:- start new project in CubeIDE and select "STEVAL-SMARTAG2"- set inputs/outputs as default (press OK when pop-up window ask me if i want to keep it)- middleware/software package... download and select FP-SN-SMARTTAG2- define platform settings (picture below)- save and run the compiler and get an errors (picture below)It looks like I miss something?Also in my further project I don't need to use all the sensors on the protoboard. I just want to use NFC-V and powering tag with energy harvesting. Thank you for your time.  

Hello,I am trying to upload the user firmware using BFU(1 slot) and Linux minicom, it always failed to complete to transfer a UserApp.sfu. I have read the UM2767 and followed all steps. But it works well on Windows Tera Term.I am testing on both of Nucleo55 eval board and custom board and using STM32Cube_FW_WL_V1.0.0(SBSFU version 2.4.0), not succeed.I have looked for the similar issues, couldn't get the workaround.There are some similar issues:https://community.st.com/s/question/0D53W00000HMk4nSAD/for-sbsfu-v240-send-firmware-file-by-linux-minicom-ymodem-failedhttps://community.st.com/s/question/0D53W00000Eba1XSAR/download-firmware-by-ymodem-failed-at-linuxLast article tells me this issue would be fixed in SBSFU v2.4.0, but I am failing.This is what I've done:defined MINICOM_YMODEM in app_sfu.hErase flash and upload the BFU.binset minicom 115200bps, 8N1, HW flow control: None.ymodem protocol setting:+------------------------------------------------------------------------------+ | Nam

Hello, we are using Stellar SR6 controller in a customer control unit. We have received SDK v 4.4.1. But this does not contain the SENT Driver.  I had also downloaded the latest StellarStudio v7.2 from the ST website. This consists of drivers only for SR5E1. Is there any newer SR6 SDK that includes SENT driver? Or could I download it from the ST website myself? Also, is the SR5E1 SENT driver compatible with the SR6 SENT peripherie? Appreciate any response to my queries above.  Thanks!  

Hello, how is everyone doing ? I am making this post because I just received a Riverdi STM32 Embedded display for my last ever studying project, as I will use it to replace 7-seg, buttons and keybord. I made a simple connection for the power supply (I soldered two wires on the connector, to avoid cutting the given cable, as I want to use it later in the final version of my project. My problem is that when I turn on the power, the screen switches on but only displays a black screen at maximum brightness. I tried reseting the device with the back button, and also created a simple TouchGFX project to display a png image and the memory flash of the microcontroller with ST-Link v2 works fine but once the flash is done, the screen goes back to the very bright black screen state. I have made some research but have not found anything interesting, so I make this post hoping that someone already had this issue or has a solution. In the meantime I have also contacted Riverdi, but I want

Hi all. I'm coding an app in C# that uses the ST25R3916DISCOComm.dll native methods to access a ST25DV04 tag. I have got many things working, including bing able to read the tag memory passively, and some complex protocols using the Mailbox mode. However, the one thing I can't get working is passive write to tag memory.Below is a debug log of my process.wait for a tag in the field and get its UID. [lines 1..3]Read the entire tag memory using iso15693ReadBlock() in a for loop [lines 5..7]Present the password to unlock user area 1 [lines 9..13]. This appears to work and doesn't return an error.Attempt to write a single block of memory to block 79 (0x004f) with value [x12,x34,x56,x78] [lines 15..19]. This is using the iso15693TxRxNBytes() method.The command packet looks correct to me based on the data sheet and other commands in a similar format in the log, but I'm getting back no received data and a "No Memory" error code. Any ideas what I'm missing?Debug log:21/05/2025 15

Hi We are developing a product that uses an STM32 microcontroller. In the microcontroller’s firmware, we have implemented a password that the user must enter at startup. If the user forgets the password, how will the program run? (Note: No software or hardware fallback has been implemented for this issue, and the source code is not accessible.)

I'm working on sensor data transfer via BLE to mobile app (like nrf connect). My STM32WB board gets connected with the app, but the data is not transmitted. When I give functions in the main while loop for transmitting, it stop the device advertisement at mobile app. How to transfer the data to mobile app? I need to send continuous sensor data to mobile app.I've also tested timer function as well. But still, it's impossible for me to transfer the data. I'm attaching the image of mobile app connection, there you can see that the value is 0. There, I need sensor data to be printed.Can anyone help me to resolve this issue? Thanks in advance!

Will STM32H743BIT6 support only OTG_HS mode? Will it support normal USB operations by disabling OTG option? If yes which pin will control that functionality?

I followed the steps in the link below and then ran main.py, but I encountered the following error. I don’t know how to resolve it. I also set the BOOT0 and BOOT1 switches on the board, but I still get the same result. https://github.com/STMicroelectronics/stm32ai-modelzoo-services/blob/main/object_detection/deployment/README_STM32N6.md (st_zoo) C:\Users\wwnso\Desktop\STM\stm32ai-modelzoo-services\object_detection\src>python stm32ai_main.py --config-path ./config_file_examples/ --config-name deployment_n6_ssd_mobilenet_v2_fpnlite_config.yaml 2025-03-14 02:35:59.704524: W tensorflow/stream_executor/platform/default/dso_loader.cc:64] Could not load dynamic library 'cudart64_110.dll'; dlerror: cudart64_110.dll not found 2025-03-14 02:35:59.705273: I tensorflow/stream_executor/cuda/cudart_stub.cc:29] Ignore above cudart dlerror if you do not have a GPU set up on your machine. [WARNING] The usable GPU memory is unlimited. Please consider setting the 'gpu_memory_limit' attribute

Software: STM32CubeIDE v1.18.0, STM32CubeMX v6.14.0, STM32CubeProgrammer v2.17.0Hardware: NUCLEO-WB09KE Hello,I am trying to observe Bluetooth functionality on a NUCLEO-WB09KE board. I have run the p2p_server example for the board unaltered, and it works perfectly. The device is discoverable using a Bluetooth scanner on my phone. However, when I try to copy the .ioc settings and BLE configuration to a custom project (no changes have been made to the .ioc file), it is no longer discoverable. Even when I copy and paste the .ioc file and create the new project from it, it still is not discoverable. I have debugged to verify that I am not ending up in an error handler, and I am not. APPE_Process is running. The only difference is that I am creating a new project and trying as opposed to copying the example from ST. I want to be able to observe BLE functionality in a custom project. Any help here would be appreciated!Matt H.

Hello,I'm working with the STM32N657X0H3Q MCU and trying to implement a UDP server . I enabled the Ethernet peripheral and selected NetXDuo in STM32CubeMX(6.14.1), then generated the code for MDK-ARM (Keil). However, two important driver files were not generated:nx_stm32_phy_driver.cnx_stm32_eth_driver.cI noticed that in your example here:"https://github.com/STMicroelectronics/STM32CubeN6/tree/main/Projects/NUCLEO-N657X0-Q/Applications/NetXDuo/Nx_UDP_Echo_Server"the two files mentioned above are included, but this example does not contain a .ioc file, so I couldn't verify how they were configured.To troubleshoot, I looked for another example with a similar configuration and found the STM32H5 series UDP example here:"https://github.com/STMicroelectronics/STM32CubeH5/tree/main/Projects/NUCLEO-H563ZI/Applications/NetXDuo/Nx_UDP_Echo_Server"This H5 example includes a .ioc file, and I observed that under NetXDuo > Network Interface, we can select:Ethernet Interface.LAN8742 PHY Drive

Hi I have a simple question about DFSDM configuration. I want to apply sinc5 with 32 samples length and therefore get 32 times decimation. Btw, I use internal ADC1/ADC2 in dual mode. STM32H725.Thus, for a given ADC frequency F I expect to get decimated frequency Fd = F/32. Here I assume that FOSR = 32 and IOSR = 1. To my opinion there should be no dependency of sinc order X.But I see quite different results. To be more accurate, I use one channel/filter block with FOSR = 1, and another one with a combination of FOSR and X to be investigated. I compared decimated frequencies of the filters and experimentally got the following relation between F and Fd (i.e. input frequency and decimated frequency):Fd = F/((FOSR+1)*X+0.85) for all FOSR > 1. If FOSR = 1, the input frequency seems to be unchanged.Just to stress: I expected Fd = F/FOSR. Perhaps, Fd = F/(FOSR+1). But why is it multiplied by X and got additional 0.85?

Hi,I am accessing a DRV8873s motor driver (SPI version) on two different NUCLEO boards. My usage is limited to reading data from 2 registries.I got it to work on a NUCLEO-STM32F411RE using SPI2, with the following settings:Motorola format, 8 bits, MSB first, prescaler 32 to get a 1.5625 Mbits/s rate, CPOL = low and CPHA = 2Edge.Now I try to do the same with a NUCLEO-STM32F767ZI and the same code and configuration (apart from the baud rate, set to 1.6875 MHz) don't work anymore.I have tried SPI4 and SPI5 on this board with the same result: the data read by HAL_SPI_TransmitReceive is not correct.Is there a difference in the way STM32F4 and STM32F7 perform SPI communication, or in the electronics? 

I've been trying to set up a timer and DMA to run a synchronous parallel bus onto a GPIO. The timer works great but the DMA keeps failing with a transaction error interrupt and disables the stream. This is on an STM32F413 chip and using TIM2_CH1 as a PWM output and DMA1 Stream 1 connected to TIM2_UP event. The DMA is configured as below: static uint16_t _waveform[2]; _waveform[0] = 0x0555; _waveform[1] = 0x0AAA; LL_DMA_SetChannelSelection(DMA1, LL_DMA_STREAM_1, LL_DMA_CHANNEL_3); LL_DMA_SetDataTransferDirection(DMA1, LL_DMA_STREAM_1, LL_DMA_DIRECTION_MEMORY_TO_PERIPH); LL_DMA_SetStreamPriorityLevel(DMA1, LL_DMA_STREAM_1, LL_DMA_PRIORITY_VERYHIGH); LL_DMA_SetMode(DMA1, LL_DMA_STREAM_1, LL_DMA_MODE_CIRCULAR); LL_DMA_SetPeriphIncMode(DMA1, LL_DMA_STREAM_1, LL_DMA_PERIPH_NOINCREMENT); LL_DMA_SetMemoryIncMode(DMA1, LL_DMA_STREAM_1, LL_DMA_MEMORY_INCREMENT); LL_DMA_SetPeriphSize(DMA1, LL_DMA_STREAM_1, LL_DMA_PDATAALIGN_HALFWORD); LL_DMA_SetMemorySize(DMA1, LL_DMA_STREAM_1, LL_DMA_

When using HAL_SPI_Transmit_DMA with STM32743, must the transmission data buffer and reception data buffer be placed in D1 RAM?Also, is there a way to dynamically allocate D1 RAM? Rather than declaring an array placed in section("D1"), I would like to dynamically allocate it like malloc. Is this possible?

Hi, I have installed MC WorkBench(6.3.2). While Project Generation it gives "STM32CubeMX not found" error. I have already installed STM32CubeMX (6.14.1), also STMCube IDE (1.2.1).Is there any setting that needs to be done?Thanks,Harsh 

HelloI want covert my quantized onnx model(develop by pytorch)  to .nb format, to enable stm32mp257 npu accelerate.I use ST Edge AI Core V2.0.0,(V2.1.0 has been not support stm32mp257).when I run generate command,it report lose file "onnx_ruler_db.json". run command：/opt/ST/STEdgeAI/2.0/Utilities/linux/stedgeai generate -m ./xxx.onnx --target stm32mp25command result：ST Edge AI Core v2.0.0-20049LOAD ERROR: [Errno 2] No such file or directory: '/opt/ST/STEdgeAI/2.0/Utilities/linux/lib/python3.9/site-packages/onnx_ruler_db.json'

I soldered a new STM32 on the board, it can enter bootloader, but it's under Readout protection(I guess I bought renovated chip), I don't know how to unlock Readout by STM32CubeProgramer, finally, I use STVP and ST-LINK V1 to connect through SWD, and change the option byte, unlock Readout protection.I don't want to use ST-LINK and STVP, because I need to have SWD interface on the PCB(the PCB space room is very limited). I want to use STM32CubeProgramer through USART to set option byte, but I didn't find out how to set option byte if the chip is Readout protected.

Hello,I use EP1 (IN/OUT) for bulk transfer(64 byte) and EP2 (IN) for interrupt transfer(64 byte).I need to use the Vendor-Specific Class for this configuration. Using STM32CubeIDE 1.18.0 to create a usb device, which class shall I use to create this  USB configuration. I tried using the Communication Device Class, because it includes EP1(IN/OUT) for bulk transfer andan interrupt transfer endpoint.(primarily for sending notifications back to host)Instead of using interrupt transfer endpoint for sending notifications,I tried modifying this endpoint to send data back to the host when it polls for it.However, the USB device does not seem to respond to the host polling.Is this the correct way to do it?I have also attached my source codethank you very much!!

Hi,I probably didn't search correctly in the documentation, but i didn't find a command to reboot the device using the USB Bootloader interface . I found a reset method but its with STLINK and its not what i'm using.Is there any method available ?thank you for all the help you can provide Sofiane

A similar problem to this post but not quite the same:I've got my own low-level LPUART transmission code, it works like this:1) Initialize LPUART in FIFO mode with thresholds at 1/2 full2) When a buffer needs to be sent, write bytes to TDR until all bytes sent or transmit FIFO is full3) If transmit FIFO is full, enable USART_CR3_TXFTIE and let the ISR handle the rest.4) When the ISR has written all the bytes to the FIFO, it disables USART_CR3_TXFTIEWhat I see is this:1) Send first packet.  It's 10 bytes long, the first byte gets moved immediately to the TX shift register and 8 bytes fill up the FIFO so there's 1 byte left.  The interrupt is enabled, the ISR fires, the last byte is written to the FIFO, the interrupt is disabled.2) Send second packet.  It's 7 bytes long so fits completely in the FIFO and the interrupt is left disabled3) Send third packet.  It's 71 bytes long, the first byte gets moved immediately to the TX shift register and 8 bytes fil

I want to use the ULPI interface & both the CAN interface for my project But I see  For USB:   Pin No: 194     pin name: PB5     Module function :  USB_OTG_HS_ULPI_D7,   ONLY ONE PIN no other pins are there   For CAN   Pin No: 194,195    pin name: PB5,PB6     Module function :  CAN2_RX,CAN2_TX     Pin No: 104,105    pin name: PB12,PB13     Module function :  CAN2_RX,CAN2_TX      How to proceed with it, since we have clash with Pin No 194?