Solved

Posted on June 25, 2015 at 12:52Do ST have any data regarding Program/Data Flash write cycles and/or wear levelling for the SPC560B device(s)? I'd like to know if we have the option of using the Data Flash for built-in test logging on our SPC560B64.

Posted on May 04, 2015 at 10:15HiI need to store a single file on the board from a PC (with ST application via USB) then I need to be able to read the file back to the PC (with ST application via USB). In addition, I need to be able to transfer the same file (via NFC) to any reader (i.e. smart phone)I have only the ''RF transceiver board'' that is connected to the PC with USB.I downloaded the demo application for it (stsw-m24lr011) but I can't make it communicate with the board via USB. Is there a way to store file on this board at all and if so, hot to accomplish this task?Thanks a lot. #nfc

Posted on May 19, 2014 at 19:38Hi ST community ! :)For a projet I�m working on, I need to save some informations coming from a �C (time, date and pressure) into a memory that must be read without any wired connections. So the NFC/RFID protocol seems to be the most appropriate way to do the trick.On the internet I could find the M24SR64 and it seems to match well with my application. Indeed, the �C will write data into the M24SR64 memory using I�C protocol and a NFC/RFID reader will ask the device to receive data when the system will be turned off.However, I have some questions� I don�t want to use a smartphone to receive data from memory but I would prefer an NFC/RFID reader. Is it possible? If yes, can you give me some reader references?Then, I guess there are special commands the reader should ask to receive the memory content. Is it possible to do it with standard RFID/NFC reader?Thank you a lot for your help,Henri #reader #m24sr #rfid #reader-command

Posted on November 07, 2014 at 15:31Dear All,I'm using in one of my products a M24LR NFC memory.Now I would like to indicate in the external case the correct position of the NFC memory with a NFC logo.Which logo could I use?Are there some restrictions on using some kind of logo?Best Regards #nfc-logo #m24lr

Posted on June 12, 2014 at 18:55Hi I am using an Arduino UNO board to make an application to read the data of my M24SR64 antenna using I2C protocol. The problem is that I don't know if I am already communicating with it. I know from the datasheet that the address to read from a M24SR64 is 0xAD.Here is the code of the Arduino UNO so I can read the data&sharpinclude <Wire.h>void setup(){    Serial.begin(9600);     Wire.begin();        Serial.println(eepromRead());   }void loop(){}byte eepromRead(){  Wire.beginTransmission(0xAD); // Opens I2C communication with M24SR64  Wire.write(0);  Wire.endTransmission();    Wire.requestFrom(0xAD, 1);    while(!Wire.available())  {      }  return Wire.read();}I have also read in the datasheet that in order to read an NDEF file I have to  Send the SelectNDEFTagApplication command, Select t

Posted on March 11, 2015 at 16:23Hi, I'm trying to set up a NDEF with multiple records.     // write NDEF message (command C-APDU - datasheet 5.2.1 p32)     ndef[0] = 0x02;                // PCB:     ndef[1] = 0x00;                // CLA: class byte     ndef[2] = 0xD6;                // INS: instruction byte     ndef[3] = 0x00;                // P1: param byte 1     ndef[4] = 0x02;                // P2: param byte 2     ndef[5] = 5 + 5 + 7 + 5 + 1;        // Lc: number of bytes of the data field     // record &sharp1     nd

Posted on May 27, 2015 at 15:39When I read my M24SR02-Y tag from the Android app ''NFC Tools v3.8'', NDEF is no longer listed as available technologies.Any suggestions as to how this can be?I do need NDEF for my application.EDIT: The official Android NFC Reader app from ST cannot read my tag. and the other app is only capable of reading it when my device is disconnected from the power supply. #android-app #m24sr02-y #ndef-technology #m24sr

Posted on January 30, 2015 at 12:06Hi everybody, I would like to know if it is possibile to interface two CR95HF so that one acts as a tag reader and the other acts as a passive tag, and vice versa. Is this a P2P communication? If so... I know that CR95HF cannot acts as P2P player. Any other solution? Thanks in advance Stefano #p2p #cr95hf

Posted on February 16, 2015 at 07:45Microsoft in Windows phone 8.1 has added new Nfc related features including low level access(Non NDEF). I have Nokia Lumia 830 (PN547 NFC chipset is present in this device).Im not able to detect Nfc tag (ANT-7M24LR-A ,ISO15693) through Lumia 830, which im able to read/write using Nfc-V(ISO15693) in Android. I also have a Lumia 720 (old NFC hardware) but atleast it is able to detect the tag. Has anyone encountered this ? Whats the workaround ? #m24lr #lumia

Posted on February 24, 2015 at 12:04Hi,For a project I use the M24LR64E-R as memory and power supply. Everything works very well if I want to read or write the M24LR64E-R. But as soon as I read another sensor, this sensor value cannot write to the M24LR64E-R. For this application I use the MCU MSP430FR of TI.Following ANs I've read:AN1471 (http://www.st.com/web/en/resource/technical/document/application_note/CD00004295.pdf )AN3057(http://www.st.com/st-web-ui/static/active/en/resource/technical/document/application_note/CD00247968.pdf )Errata sheet for M24LRXXE-R(http://www.st.com/st-web-ui/static/active/en/resource/technical/document/errata_sheet/DM00052762.pdf )But I don�t see any solution.Questions:1-      1- Can we use the M24LR64E-R constantly on the RF Field (For power supply)? And at the same time using the I2C bus with other sensors? (This has been going when I use only the MSP430 and the M24LR64E-R).2-      2- Does anyone

Posted on May 25, 2015 at 08:58Good day,  I have a rquirement where I need to use EUI-64 address.  The M24LR04E has a unique 64bit address.  Can I use this as an EUI-64 address? #uid #m24lr #eui

Posted on June 23, 2015 at 09:05Microsoft in Windows phone 8.1 has added new Nfc related features including low level access(Non NDEF). I have Nokia Lumia 830 (PN547 NFC chipset is present in this device).Im not able to detect Nfc tag (ANT-7M24LR-A ,ISO15693) through Lumia 830, which im able to read/write using Nfc-V(ISO15693) in Android. I also have a Lumia 720 (old NFC hardware) but atleast it is able to detect the tag. Has anyone encountered this ? Whats the workaround ? #iso-15693 #m24lr #lumia

Posted on July 25, 2014 at 16:21We would like to use the MB1054A ''wand'' from a Linux box, to interrogate a M24LR04E tag embedded in our product, but the available software from ST is based only on Windows. Does anyone know of Open Source drivers and library code to support this wand? Many thanks in advance, Jon #cr95hf #linux #mb1054a-cr95hf-linux-open-source

Posted on June 17, 2015 at 07:45Hello, For an upcoming project, I would like to use the SPC56EL54L3 controller. But when I was setting up a SPC5 Studio project, I can´t choose this controller in the platform settings because it is not listed. Is there a reason why this controller isn´t implemented in the ''Specific Model'' in platform component configuration? Best regards, Patrik

Posted on May 07, 2015 at 10:57 Hello, I would like to use the input capture functionality of eTimer on SPC56EL. This is my eTimer configuration: ETIMER_0.CHANNEL[0].CTRL1.B.PRISRC = 0b11000; ETIMER_0.CHANNEL[0].CTRL1.B.SECSRC = 0b00010; ETIMER_0.CHANNEL[0].CTRL1.B.CNTMODE = 0x3; ETIMER_0.CHANNEL[0].CTRL1.B.LENGTH = 0x0; ETIMER_0.CHANNEL[0].CTRL1.B.DIR = 0x0; ETIMER_0.CHANNEL[0].CTRL2.B.OUTMODE = 0x3; ETIMER_0.CHANNEL[0].CTRL2.B.OEN = 0x1; ETIMER_0.CHANNEL[0].CCCTRL.B.CLC2 = 0x5; ETIMER_0.CHANNEL[0].CCCTRL.B.CLC1 = 0x2; ETIMER_0.CHANNEL[0].CCCTRL.B.CMPMODE = 0x0; ETIMER_0.CHANNEL[0].CCCTRL.B.CPT2MODE = 0x1; ETIMER_0.CHANNEL[0].INTDMA.B.ICF2IE = 0x1; ETIMER_0.CHANNEL[0].INTDMA.B.CMPLD1DE = 0x1; ETIMER_0.CHANNEL[0].INTDMA.B.CMPLD2DE = 0x1; ETIMER_0.DREQ[0].R = DREQ_ENABLED | DREQ_CMPLD1_CH0; ETIMER_0.DREQ[1].R = DREQ_ENABLED | DREQ_CMPLD2_CH0; The primary input source is the bus clock, the secondary input source is an external signal. T

Posted on May 08, 2015 at 04:52Hi. while I am reading SIU PCRxx for Pin Assignment in RM0015 SPC563Mxx Reference Manual, It is not clearly described about Pin Assignment PA[2:0] value. eg. SIU_PCR179. what is value of PA[2:0] for each function of eMIOS[0]_eTPU_A[0]_eTPU_A[25]_GPIO[179] pin. Or, in whcih document I can find these definitions. thank you so much!1 #pcr

Posted on March 31, 2015 at 14:41Hi there,I have SPC5 studio installed and I updated all the components available (so my core and app wizard are 3.4.3). I am trying to run OS-less CAN test application from the wizard, having chosen the EVB I have (the SPC560BADAPT144S), and it won't compile out of the box.I get make: *** No rule to make target `all'. The standard thing to do in this case would be to have eclipse generate the Makefile it needs, but the option ''generate makefiles automatically'' is grayed out in the builder setting tab of C/C++ Build in the project properties.Any advice would be appreciated.

Posted on November 25, 2014 at 13:18Hello, Yesterday, I investigated a problem with my software project for an SPC560B. There are several calculations running on the controller and it additionally communicates over UART with a PC. When I tried to increase the UART baud rate, I got the effect that the controllers ''miss'' some bytes sent by the PC. I found out, that reason for that effekt has something to do with the UART RX interrupt and an interrupt created by the periodical timer PIT. After the PIT causes an interrupt, the UART RX can not trigger an interrupt. I always thought that a higher priority interrupt can break the program even when another lower prior interrupt is currently running? Best regards, Patrik

Posted on April 05, 2015 at 15:54Hi I Want to use ADC of My SPC560B-DIS , first there is not an example for this Dev Board in SPC-Studio but when i want use the other samples for ADC when i want to set ADC pin, in pinmap wizard i have a Warning and the program is not work , i do not know the problem is in my program or the pin map cuase this . I attach a screenshot in the message . please help , if any one have an ADC sample for this Dev Borad please send to me . thanks with best regards Vanima

Posted on November 19, 2014 at 23:58Having some trouble getting my motor to start.. The code is getting stuck in the R3_4_F30X_TurnOnLowSides function. It enters the timer GetFlagStatus where it should be returning bitStatus = SET but instead is returning RESET. Any ideas on what I'm doing wrong?Screenshots from debug: #foc-library-stm32 #foc-lib-4.0

Posted on February 17, 2015 at 09:49Hello, I can't get either read or write (over I2C) to work correct. If I write the text ''Hello World!!'' from the phone (S3) and then read it over the I2C I get the following error. When I read the length it says 0x14, but if I try to read anything over 0x10 it will fail (only sending FF...), but if I read only 0x10 (or less) it will work?! Same when I try to write (over the I2C), then I will get the error code 67 00, but I can't see what's wrong. If I read it with the phone it says it's empty, but if I read it over the I2C I can find it there. Below is a summery over what I send (and get back) over the I2C. Anyone that can tell me what I'm doing wrong? Grateful for help!void InitNFC(){   //Send ''Kill RF and open I2C   Send AC 52   //Select NFC-T4   AC 02 00 A4 04 00 07 D2 76 00 00 85 01 01 00 CRC CRC   //Read back answer from M24SR   Write AD, READ 02 90 00 CRC CRC     // select CC   AC 03 00 A4 00

Posted on January 19, 2015 at 06:55Dear Sirs: We are using M24SR64. Now we met a problem with NDEF File Length in 36 bytes. Problem: 1. If the NDEF File Length is 36 bytes, it can not be a successful data in Android OS or NXP TagInfo app or NFC TagInfo app. Only the app of ST ''M24SR Demo'' can show the payload we wrote. 2. If the NDEF File Length is 35 or 37 bytes, it is a successful Tag data. At first, we used I2C to write the data and we met this strange behavior. Then we used the M24SR Demo app to test it, it also fail in 36 bytes (35 or 37 are OK). Here is a simple way to reproduce the stange behavior: - Tested in Samsung S3 (Android 4.3, may PN544) and Nexus7 generation1 (Android 4.4.3, may 65N04) - Use the app M24SR Demo (download from Google Play)   -> Choose the NDEF editor and TEXT mode   -> Key in the data (payload)         1234567890         1234567890       

Posted on March 09, 2015 at 15:01using the SPC560B-DIS board I'm having trouble with eDMA. I've got a very basic function set up to write a succession of 32bit words from one array to another using the eDMA. but it doesn't seem to ever get on to the second (or subsiquent) major loop iterations (as in CITER decriments the once but then not again) If i manually reset the TCD.START, the next iteration happens (and if I keep doing this the iterations continue till CITER is zero and the done flag is activated) However I assume that subsiquent 'loops' should be started by hardware. Any help with this would be appreciated. #discovery #iter #dma

Posted on January 19, 2015 at 10:45Hello,I am trying to build a project created using SPC5Studio Wizard. The steps used are File->New->SPC5Studio Wizard. Afte this I selected SPC560D-DIS as the product line. Then selected all the drivers with OSLess version. I selected all the available applications for this configuration. I tried building one of the application - SPC560Dxx OS-Less Test Application for Discovery, it is giving following errors,- Symbol 'NULL' could not be resolved- Symbol 'uint32_t' could not be resolved- Symbol 'int32_t' could not be resolved- Symbol 'uint16_t' could not be resolved- Symbol 'uint8_t' could not be resolvedSimilar errors for different defines used in main.c file are there. Few errors are for the functions used like osalThreadSleepMilliseconds().Can you please help me resolve these? Is any project setting/configuration missing?Your earliest help in this regard will be highly appreciated.Thanks in advance for all your help.Mike.

Posted on February 05, 2015 at 13:43Hello members,1. Has anyone tried implementing sleep/power down modes with SPC560Dxx series MCU? I tried going through reference manual (CD00259063.pdf) but hardly any information is available. Any app note or document reference?2. Has anyone tried with any of the SPC560 series MCU? Any app note or document reference?Thanks.Mike #sleep/power-down