Solved

Posted on January 31, 2018 at 10:42Hi!At the manual script en.DM00206508.pdf (DoclD027973 Rev 5 -- Datasheet of STM32L011x3/4) at page 67/119 I have a misunderstanding. I wanted to look over the temperature stability over the HSI16 oscillator and the values in the table 38. (16MHz HSI16 oscillator characteristics) varies from the Figure 22 (HSI16 minimum and maximum value versus temperature - MSv34791V1).The STM32 is supplied with VDD=3.0V and VDDA=3.0V and int the table 38 the values for a ambient temperature TA=-10°C to 105°C are -4% to 2%. At the other side in Figure 22 with (minimum and maximum values) is a 3V operated chip over -45°C to 125 °C with a maximum variation of the oscillator of 1%.Please help me clarify this discrepancy.

Posted on November 05, 2017 at 23:24Hi,STSW-ST25002 (ST25 Android Source code package) seems to have disappeared?It was there before at version 1.0.6.Kind Regards,Martin.

Posted on January 30, 2018 at 15:53hello friends i recently got an stm32l4 I just go past the led blink i am trying my hands on interrupts I am trying to configure  a falling edge triggered interrupt on A0 and PC15 so far works fine for GPIOA but the interrupt for GPIOC15 is not working I have enabled pull up on the pin but when i drive it low it doesnt trigger the interrupt during the debug i know cause the counter in the ISR is not incrementingdoes anyone know why my c code is below i am using keil ide thank you#include 'stm32l433xx.h'extern int cnt,j;void EXTI0_IRQHandler(void){if (!(GPIOA->IDR & (1<<0)) ) { if(!(cnt%2)) GPIOC->ODR =~(1<<4); else GPIOC->ODR|= (1<<4); cnt++; }//Clear the EXTI pending bits NVIC_ClearPendingIRQ(EXTI3_IRQn); EXTI->PR1 |=(1<<0);}void EXTI15_IRQHandler(void){ j++; NVIC_ClearPendingIRQ(EXTI15_10_IRQn); //Clear the EXTI pending bits EXTI->PR1 |=(1<<15);}void Config_IO(void) { RCC->AHB2ENR |

Posted on January 30, 2018 at 16:13I just ordered and received REV C of this board, all of the files online seem to indicate they apply to REV B of the board, is anyone aware of the changes or has access to the appropriate files? #stm32f429i-disc1

Posted on January 25, 2018 at 11:46Hi,I would like to use BlueNRG-2 in my project. I downloaded BlueNRG-1.2 DK software package. There is a lot of examples of applications. They use an archive library libbluenrg1_stack.a containing compiled Bluetooth LE stack.Where can I find the sources of this library, and how can I build it with Atollic TrueStudio?Regards,Piotr#stack #bluetooth-le #bluenrg-2

Posted on January 29, 2018 at 12:02Hello!Is it possible to send a UART break (0.3 seconds) over the Virtual COM Port.It seems that UART break is connected with NRST.-Thomas

Posted on January 29, 2018 at 21:09Hello, I am using STM32F103 and STM32F301. I need to use the SPI that shares the same pin as SWO. Is it possible to move the SWO to a different pin so I can retain the printf to console functionality for debugging?

Posted on January 30, 2018 at 07:16Hi Sir,In the data sheet of ST25TV02K, it introduces that:'Present password command specificity Before doing a present password command, it is necessary to obtain a valid random number through the command ‘Get_Random_Number’ (see Section 6.4.41: Get Random Number) The passwords must be presented encrypted as explained in a Technical Note available on request.'But I don't find the 'Technical Note' to explain how the password is encrypted and presented?As my understand, 1, execute Get_Random_Number command to get a random number (two bytes);2, some rule to generate an encrypted password with the random nuber and raw password(four bytes);3, execute 'Present password' command with the encrypted password.Can you review if I am right and tell the detail for step 2?Thanks,Arna

Posted on January 26, 2018 at 10:45Hi to all,We are usin this accel over i2c with this configuration:* Separate VDD and VDDIO (this one is attached to CS).* SDA and SCL are mounted with a external pull up resistor of 10K.* SDO/SA0 is left unconnected (it is supposed to have an internall pull up).Is there any power up sequence to ensure the i2c mode is properly configured/selected? Any delay between VDD and VDDIO?Powering up both lines to 3V, the VDDIO is not 3V, its in 1.9V or similar. If we disconnect CS from VDDIO. In CS we get a '0' and in VDDIO 3V. Is this normal? And the internall pull up resistor does not lift the pin to high?Is there any example of how to connect the accel for i2c communications? any keynote for the power up?Attached is an image of the mounted sensor were the marking is a dot, a datamatrix and a 'T'.Thanks in advance for your help.#lis2dw12 #i2c

Posted on June 25, 2017 at 19:25Currently the search in the pinout view searches the labels. It would be nice if there was some way to search pin functions, too. Eg., all the pins that have I2C2 anything as their alternate function.

Posted on January 25, 2018 at 12:18I need to re-upload original firmware to ST25R3911B-DISCO with STLink-V2.(Discovery GUI is not applicable for me here, I need to do it exactly with STLink-V2)I connected with wires:- 20-pin's VCC (1) to 10-pin's VTREF (1)- 20-pin's GND (4) to 10-pin's GND (3)- 20-pin's GND (6) to 10-pin's GND (5)- 20-pin's TRST (3) to 10-pin's NC (9)- 20-pin'sSWDIO(7) to 10-pin'sSWDIO(2)- 20-pin'sSWCLK(9) to 10-pin'sSWCLK(4)- 20-pin'sSWO(13) to 10-pin'sSWDIO(2)- 20-pin's TDI (5) to 10-pin's TDI (8)When I connecting both devices to same PC and running utility and trying to connect, it connects, ST-Link V2 has green LED light, but next I seeing: 'Unknown device id' and after clicking 'OK' it has red LED light again.I tried Target -> Settings... with all combinations of JTAG/SWD and connection modes.and no effect.Help me please! Deadline to this task is too near!

Posted on January 24, 2018 at 01:12Hi I am currently trying to send and receive APDU commands to an NFC PICC. I am using the X-NUCLEO-NFC05A1 (ST25R3911B) and the STM32F401RE Nucleo Board. For software I am using X-CUBE-NFC5  RFAL middleware and STM32CubeF4 HAL.The Card is a ISO14443A Type 4 ( ISO-DEP)I can read the UID and Type of the Card, but as soon as I try to select the first card (rfalNfcaPollerSelect), the function responds with timeout error ( 0x04).I have gone through the RFAL.chm file multiple times and cant seem to find a resolution to my problem. Am I missing some initialization or setting?Partial Code ( based on example from X-CUBE-NFC5 )void loop(){       rfalWorker();      //code for inductive wakeup then run scanA() //(code not shown to save space)       scanA();}void scanA(){      rfalNfcaSensRes          sensRes;&

Posted on January 28, 2018 at 16:09I am using the STM32H743 together with uVision 5.Are there any example-programs available not using RTOS2 and CubeMX ?What I am missing are simple demo-programs like Blinky ( without RTX ) and a demo-programusing the LCD ( without a GUI, yust a simple output of text would be fine ).I have available a project, the only purpose shall be to switch an LED on,it compiles, links and flashes without error, but nothing else happens...Probably an initialisation-problem but I need a working example to get on the right path.

Posted on January 28, 2018 at 10:43I connect my board with STM32L462 to PC using PA2/PA3 (USART2) through USB2COM, but STMFlashLoader Demo cannot recognize this device.It looks like the Flasher is too old (2015), are any other solution?#stm32l4-bootloader #usart-bootloader

Posted on January 25, 2018 at 10:19hi guys.i wrote a code with IAR , and when is run the code in stm32f103ret , cpu go to  the interrupt s routin.i dont know why??!!i want to have 1msecond delay for each timer priode , but i cant do that. when the code runs , cpu go to interrupt routine fanction. i do some thing that i know. but i cant do this activity. this is my code:who know why I cant??so thanks.#include 'stm32f10x.h'#include 'stm32f10x_gpio.h'  // for Enable LCD#include 'stm32f10x_rcc.h'   //for Enable LCD#include 'stm32f10x_tim.h'#include 'LCDLib.h'#include 'delay.h'void tim_init(void);void GPIO_init(void);void TIM1_UP_TIM16_IRQHandler (void){  int i;  i = TIM_GetPrescaler(TIM1);    lcdGoxy(1 , 2);  lcdPutInt(i);  lcdGoxy(1 , 3);  lcdPutString ('tim activated');  TIM_ClearITPendingBit(TIM1,TIM_IT_Update);}int main(){    lcd_init();   tim_init();  GPIO_init();   while(1){     

Posted on December 22, 2017 at 09:55 Hello, I'm trying to make my application position independent so that I canplace the software anywhere in the flash of the SPC564B I'm using. Is this possible using the free FreeGCC v4.9.3 with VLE support? If so, is there a guide available on how to solve this? When I'm trying to just add -fpic, -fPIC or -fpie I get illegal instructions: make all ppc-freevle-eabi-gcc -c -mcpu=e200z4 -meabi -msdata=none -mregnames -mvle -O2 -gdwarf-2 -fomit-frame-pointer -falign-functions=16 -fno-gcse -Wno-missing-field-initializers -fpie -ffunction-sections -fdata-sections -fno-common -Wall -Wextra -Wstrict-prototypes -Wa,-alms=build/lst/queue.lst -DPPC_USE_VLE=1 -D__FREERTOS__ -DconfigUSE_APPLICATION_TASK_TAG=1 -DconfigUSE_TRACE_FACILITY=1 -D__SPC5__ -DNPI_USE_BLEIO -DNPI_USE_UART -DNPI_MASTER -DDEBUG -DEVTLOGPINS -D__POLESTAR_PAK -DPAKM_LOW_POWER -DNATIVE_BIG_ENDIAN=1 -DSODIUM_STATIC -DNPI_POLESTAR -DPAKM_PROTO_V1 -DPAKM_PROTO_V2 -MD -MP -MF .dep/qu

Posted on January 24, 2018 at 20:27 With my STM32F4 I am trying to use an external interrupt to read aquadrature encoder on PC02 and regular port PC The interrupt on PC02 fires when I move the encoder, but it won’t return to the main loop again and my main routine gets stuck. Here’s the code: init() { GPIO_InitTypeDef gpio_init; EXTI_InitTypeDef exti_init; NVIC_InitTypeDef nvic_init; RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE); RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE); gpio_init.GPIO_Pin = GPIO_Pin_2 | GPIO_Pin_3; gpio_init.GPIO_Speed = GPIO_Medium_Speed; gpio_init.GPIO_Mode = GPIO_Mode_IN; gpio_init.GPIO_PuPd = GPIO_PuPd_UP; GPIO_Init(GPIOC, &gpio_init); SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOC, EXTI_PinSource2); exti_init.EXTI_Line = EXTI_Line2; exti_init.EXTI_LineCmd = ENABLE; exti_init.EXTI_Mode = EXTI_Mode_Interrupt; exti_init.EXTI_Trigger = EXTI_Trigger_Falling; EXTI_Init(&exti_init); NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); nvic_init

Posted on September 21, 2017 at 03:47Hi,I would like to generate the code by using STM32CubeMX for STM32L4 Discovery kit IoT node (B-L475E-IOT01A).But I don't see the STM32L4 Discovery kit IoT node in the Boards List.Could you suggest for me?Thank you

Posted on January 19, 2018 at 16:55Hello,Do you have a reference schematic design for an audio application of the AS21P2TLR ?Best regards,

Posted on January 23, 2018 at 16:15Hi everybody,i'm using the ADC on STM32L051.After enable operation (ADEN = 1) it will not be ready never (ADRDY bit).I put my code hereCan you help me?thanks in advanceDamianoRCC->APB2ENR = RCC->APB2ENR | 0x200; //ADC Clock enableADC1 -> CFGR1 |= 0x00008000; //ADC Auto-off enable if((LL_ADC_IsEnabled(ADC1) == 1) | (!(LL_ADC_REG_GetDMATransfer(ADC1) == LL_ADC_REG_DMA_TRANSFER_NONE))) //if AD and DMA are enabled { LL_ADC_Disable(ADC1); LL_ADC_REG_SetDMATransfer(ADC1, LL_ADC_REG_DMA_TRANSFER_NONE); }LL_ADC_StartCalibration(ADC1); //Calibration enabledwhile(LL_ADC_IsCalibrationOnGoing(ADC1)==1) { //Add timeout code }cal_fact = LL_ADC_GetCalibrationFactor(ADC1);//read ADC -> to move from hereLL_ADC_SetClock(ADC1, LL_ADC_CLOCK_SYNC_PCLK_DIV1); LL_ADC_SetSamplingTimeCommonChannels(ADC1, LL_ADC_SAMPLINGTIME_7CYCLES_5);LL_ADC_SetResolution(ADC1, LL_ADC_RESOLUTION_12B); //LL_ADC_REG_SetSequencerScanDirection(ADC1, LL_ADC_REG_SEQ_SCAN_DIR_FORWARD);

Posted on January 23, 2018 at 21:51Is there a quick and clever way of inverting a PWM signal in software (I am using timer 2 of the Discovery Kit board/STM32L100)? Was looking for the complementary feature but I don't want a pair of PWMs, just the inverted of the original signal (top).Thanks in advance!

Posted on April 13, 2017 at 10:27 SPCSetRunMode not return ...... board: Discovery Plus Kit for SPC56 L line - with SPC56EL70L5 MCU my step: file->new sp5 studio Application wizard-> select Discovery Plus Kit for SPC56 L line - with SPC56EL70L5 MCU click generate button and click build button program FLASH and debug... Has been parked here.... I didn't changed any code...

Posted on January 23, 2018 at 17:40Hi,I'm trying to transfer data to SAI's fifo via DMA (memory-to-peripheral). I'm following reference manual's instructions for setting up DMA for SAI.As soon as I enable the DMA channel FEIF4 (FIFO overrun/underrun) flag becomes active. After enabling the SAI2 interface and waiting few clock cycles TEIF4 (Transfer error) flag becomes active and disables the DMA channel. I've attached SAI2 A and DMA2 stream 4 register values below. I have no experience with DMA or SAI so maybe there's something wrong with the registers. If the registers seem OK could this be clock issue? Any help would be greatly appreciated. Please ask more info if you need to.MCU: STM32F446ZESAI2 A REGISTERSDMA2 STREAM 4 REGISTERS

Posted on October 18, 2017 at 18:06Hello everyone. My current project requires working with NFC and RFID interfaces. I use ST M24SR to interact with NFC-powered smartphones, NXP PN532 to read 13.56 MHz cards and inhouse-designed circuitry for reading 125 kHz em-marine cards. So I have three antennas put one inside another. I turn each of these ICs for short moment of time to scan for appropriate tags or phones. If I turn two of them simultaneously collision occurs and weird behavior happen. When M24SR antenna is situated aside others everything seems to be OK. But when I put all antennas together as required by device design I observe following behavior: when I disable RF frontend on M24SR using RF disable, pins AC0 and AC1 behave like a short circuit and act as pretty heavy load for other antennas. So, when activated M24SR is able to interact with smartphone, but all other parts of my device cant properly work. I was thinking about putting RF switch in series with&nbsp

Posted on January 23, 2018 at 16:29Good day everyone,I have a slight issue, I'm storing data in the form of uint16_t data types.This data will be read in from an ADC and have values of 0 and 1. I'll have an array of 192 of these 16 bit values that I'd effectively like to store in a SDcard. The problem is that I can't directly send these to the sdcard using fwrite as it would be completely unreadable, so I'd need to convert it to a char datatype. It seems a little counter-intuitive as char are 8 bit long and I'd need to cast 192 of these 16 bit unsigned integers.I tried doing a cast to wchar_t and it works perfectly in the code. I can cast a uint16_t value to a wchar_t without it seeming at all computationally expensive, although when I try to send this to f_write and send it out I get complete junk.Is there any computational inexpensive way that I can get a uint16_t array[192] into a readable format for text or binary files?Here's a code snippet of what I've used:uint16_t aDST_Bu