Solved

Hi,I am using a custom board with the following CPU : STM32F746BGTx.Here is the pinout :PB2 : QUADSPI_CLKPB6 : QUADSPI_BL1_NCSPF6 : QUADSPI_BL1_IO3PF7 : QUADSPI_BL1_IO2PF8 : QUADSPI_BL1_IO0PF9 : QUADSPI_BL1_IO1How can I load all the assets (images, font, ...) into the QSPI N25Q128A ?I know I need to use an external loader but I don't know how to create it...Best Regards

To understand capacitive touch / TSC library based application, I’ve been studying the polling based sample code given in AN5105 for STM32F072B-Disco evaluation board. After tweaking the code to customize for the application, I’ve a few questions as below which I am not able to understand and can’t find any explanation even after reviewing various application notes from ST. Your input would be much appreciated and would be very helpful for me to clarify the concepts of TSC.1. Resolution and Calculation of touch Position on the slider in the range of 0...255:The header file, tsl_conf.h, supplied by TSC, has the following parameters:#define TSLPRM_LINROT_RESOLUTION (7) //Position resolution in number of bits (range=1..8)#define TSLPRM_USE_3CH_LIN_H (1) //Half ended electrode designMyLinRots[0].p_Data->Position structure is used to compare the position value in the range of 0...255, but I am not able to understand the correlation of the value and position of touch on the slider / chann

Which evaluation board I can use to practice and develop code on Capacitive Touch Sensing, which is suitable with STM32F302R8?I have STM32F302 Nucleo board with STM32F302R8 MCU, which supports touch sensing. I need to learn and develop a practice code for capacitive touch sensing - sliders and buttons with this MCU and Nucleo board.Which evaluation board I can use with this MCU that provides capacitive sliders / buttons and allow to develop a capacitive development practice project?I am new to capacitive sensing code development, so some initial guidance about how to start would be very much helpful...Thank you

..

Hi all, i realized that , printf doesnt work after wake up from sleep mode, i am using rtc to wake up mcu from sleep mode every minutes. Here is my structure config.sAlarm.Alarm = RTC_ALARM_A; sAlarm.AlarmDateWeekDay = 0x31; // Nonspecific sAlarm.AlarmDateWeekDaySel = RTC_ALARMDATEWEEKDAYSEL_DATE; sAlarm.AlarmMask = RTC_ALARMMASK_DATEWEEKDAY | RTC_ALARMMASK_HOURS | RTC_ALARMMASK_MINUTES; sAlarm.AlarmSubSecondMask = RTC_ALARMSUBSECONDMASK_NONE; sAlarm.AlarmTime.Hours = 0x0; sAlarm.AlarmTime.Minutes = 0x0; sAlarm.AlarmTime.Seconds = 0x0; sAlarm.AlarmTime.SubSeconds = 0x0; sAlarm.AlarmTime.DayLightSaving = RTC_DAYLIGHTSAVING_NONE; sAlarm.AlarmTime.StoreOperation = RTC_STOREOPERATION_RESET;Every one minute, this code works. void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc)   {   __HAL_RTC_ALARM_EXTI_CLEAR_FLAG();   gsm_machine_debug("\r\nHAL_RTC_AlarmAEventCallback \r\n");   //send_data_flag = 1;   }But if i put to mcu to sleep mode with debug

Hi Guys,is there any example code for the STM32H757I-EVAL in the STMCubeH7? in the landing page there is a zip file with compiled examples but no code itself. Also it looks like the BSP in the STMCubeH7 does not have any support for the STM32H757I-EVAL. Do you know something about it?Best,

 STM32F103C8 , with MXCUBE, MDK-ARM V5. I would like to know how to program to store the counter value in flash memory even in power failure. when power goes up automatically recall the counter value. Please support me to solve this. I am not fully aware of microcontrollers. I am RF engineer.

I am working on NUCLEO H743ZI2 and I want to use PF0 and PF1 pins as I2C2. But on nucleo board NC is written on these pins. Can I use these pins as I2C2?

Posted on January 11, 2018 at 11:54Under Linux Debian Stretch:- if I use the shortcut nothing happens- if I type ./STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin/STM32CubeProgrammerLauncher,I have this error message: Error: Could not find or load main class com.st.app.MainWhat should I do in order to run Cube Programmer ?RegardsCedric

..

Hello,On a working project with TouchGFX, i have over 150 TextBuffers (wildcards) which i access and change/edit on runtime.Now i am trying to edit some code parts to avoid repeated parts (many IF conditions).Is there a way to use a table with pointers and access the desired TextBuffer each time;

Hello, I am working on a project in which I have to store the data from my ADC (in continuous mode with DMA) on a SD card (with FATFS and SDMMC1) without losses. I try to use a ping pong buffer but when I want to change the bufferinwhich the ADC store values I have to stop my adc and restart it with the good buffer in parameter. Thus I lose a lots of data because of that.Do you have a better solution to this matter ?I also use my SD card in 1 bit mode because when I want to use it in 4 bits mode I have the RXOverrun flag. Fatfs is not configure to work with DMA because I don't know how to do it.***EDIT 1***I tryed to use a pointer in second parameter of HAL_ADC_Start_DMA() but it never write in the second buffer enven if my pointer is set at the 2nd buffer's adress.Thank you for your help.Best regardsMathieuHere is my main functionres= f_mount(&fs, "0:", 1); if (res == FR_OK){ HAL_GPIO_TogglePin(LD1_GPIO_Port, LD1_Pin); } res = f_open(&SDFile, "test.bin", FA_CREATE_ALWAYS|

I have problem with Wildcard Characters and Wildcard Range as bellowIn the Wildcard Characters i putted: a-z,A-Z,0-9.In the Wildcard Ranges i putted: a-z,A-Z,0x20-0xFE,0-9 I can show String and number OK, but only string of string or string of number.When i show string like "30TH" or number "2020" it can't show Wildcard Buffer 30th = 10 Wildcard Buffer 2020 = 5My code like:oxyDateArr[29]= "30th";Unicode::strncpy(txtOxyDateBuffer,oxyDateArr[29],strlen(oxyDateArr[29])); // for case 30thUnicode::snprintf(txtOxyYearBuffer, sizeof(txtOxyYearBuffer), "%d",20+2000);//for case 2020but screen show: =?1/2? and ?u?Anyone can help me solve those problem and explain What are Wildcard Characters, Wildcard Ranges? Thanks Everyone

I am new to the STM32 microcontrollers and I am experimenting with the SPI peripheral (interrupt mode, non DMA, slave) of the STM32F410. I noticed that the reference manual mentions the SPE bit (bit 6 of the SPIx CR1 register) but does not provide much explanation to it.I was wondering what disabling the SPE bit does after each SPI transaction. Does disabling the SPI SPE bit (at each SPI CS rising interrupt) clears the Rx buffer and the Tx buffer? Is the code snippet below for operating the SPI at the GPIO interrupt side correct?void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin) { if(GPIO_Pin == SPI2_CS_Pin) { if(HAL_GPIO_ReadPin(SPI2_CS_GPIO_Port, SPI2_CS_Pin) == GPIO_PIN_RESET) { /* SPI CS Falling Edge Interrupt Handler */   /* Enable SPI2 SPE bit to listen to master device for SPI byte */ SPI2->CR1 |= (0x1 << 6);   /* Exchange byte with master device and do further processing in HAL_SPI_TxRxCpltCallback and main loop */ HAL_SPI_TransmitReceive_IT(&hspi2,

Good evening,I requested the download for XSBSFU package last week , but never received a conformation Email. Today I made another one request and got a conformation Email. I read that it might take up to 48h to get the link, which would be to late for me, my workshop begins tomorrow at 9:00. Is there a way to speed up the process so I can participate ST-Workshop tomorrow?Thank you very much.

Hi... there Hope all are doing well From past few days I'm playing with SBSFU with STM32 L4 Cell-01 Discovery board I'm using x-cube AWS default application with default settings of the linker fileIn demo code, I've added SDMMC with FAT fs, which is working well Now I need to send the sensors data to aws at some predefined interval by RTC having calling semaphore from ISR I've created the separated thread to read the sensors data having stack size of 512 Now the problem is, due to new thread cloud_run thread calling to malloc fail Handler to solve the issue, I've allocated 2K heap to project (default 18000 to 20000) in linker script However that cause the APPLI_region_RAM  over flow by 2048 bytes!I need to know, how i can effectively allocate the RAM for the application region After checking all the linker files, i got to know SRAM1 is used for the entire project What is the best way to share the application between SRAM1 and SRAM2 Here I've attached the memory analyzer with

Hi,I am creating a project with TouchGFX graphics on STM32F412G-DISCO. I have already downloaded and installed XCUBE-TOUCHGFX 4.14 and it is visible in "additional software" category. When selecting driver, the LTDC is grayed out. (attached) It is also absent in the "multimedia" category. How to enable LTDC. Please suggest on this. Thanks,EshwarENV:CUBEMX 6.0.0TOUCHGFX 4.14MCU REPOSITORY: stm32cube_fw_f4_v1250WIN 10 x64

..

Hi!I requested the download on Saturday (sorry - I missed the first mail regarding the setup and was'nt aware of the delay in granting download permission...I started the setup late on Saturday) - I read that it might take up to 48h to get the link, which would be tonight (with the actual training starting tomorrow).Is there a way to speed up the process so I can set up the environment now to be ready for tomorrow?

I went onto the website to download their STM32 Virtual COM Port Driver Version 1.5 but instead my installation kept ending with Driver Version 1.4 being downloaded. Another problem is there is no Flash Loader Demonstrator.

Hi,I'm writing some generic utilities for use across multiple projects and processor types.Quite often I have to include the device header file in the utility header, e.g.//#include "stm32f1xx_hal.h"//#include "stm32l4xx_hal.h"#include "stm32f7xx_hal.h"Is there a compiler variable that specifies what the processor is? Then I could do something like the below for each of the processor types.#ifdef stm32f7xx#include "stm32f7xx_hal.h"#endif#ifdef stm32f1xx#include "stm32f1xx_hal.h"#endif#ifdef stm32f4xx#include "stm32f4xx_hal.h"#endifThanks.

Hi There,I have a question regarding with DDR3L fly-by topology suggested to use by the design guide.My understanding is that STM32MP1 does not support the write/read leveling feature suggested in the JESD standard.If my above understanding is correct, may I ask then why fly-by topology is still recommended as opposite to the T-topology?I thought the main reason DDR3/DDR3L uses fly-by topology is because the write/read leveling feature allows the controller to compensate the skew between CK/DQS caused by the daisy chain connection from fly-by topology.I have also seen other vendor's hardware development manual (i.e. NXP iMX7) that specifically recommend not to use fly-by topology, as their chip does not support write/read leveling feature.Am I missing something here? or perhaps my understanding is incorrect?Appreciate your assistance in advance.Thanks.Regards,Steven

Steps to reproduce:Enable asynchronous UARTEnable Tx and Rx pins swappingSelect LL driver instead of HAL.Code generated at end of MX_UART4_Init:LL_USART_Enable(UART4); LL_USART_SetTXRXSwap(UART4, LL_USART_TXRX_SWAPPED);Reference manual states pins must be swapped before UART is enabled.

Hello,I got this board and connected power and could not see any activity on the ST-LINK USB port (J11). I installed the drivers and used 115200,8,N,1, no flow control. There's no startup message or response to CR or serial echo.I can connect to the wireless network (sprinter, I think), on my phone but I cannot access the webserver at 192.168.0.1. I can't connect either my laptop or my iMac to the wireless; it fails to authenticate (I'm using the WEP key 1122334455).Thinking the board is just unprogrammed, I built the project in AC6 System Workbench. The project builds clean and generates Marlin.elf and Marlin.bin. I followed the procedure in UM2067 to jumper J22, mount USB drive, drag image in, hit refresh, etc. I waited several minutes but Marlin.bin never disappears from the root directory, and no error logs are created. I then used ST-LINK to load Marlin.elf and Marlin.bin (both file types are supported), but again, no terminal activity on J11 serial and I cannot log into the wirel

Hello, I'm using FreeRTOS on STM32F746NG.I have created 4 task which run with the same priority. But when I run my code,Only StartDefaultTask running, others aren't.In debug mode, when I clicked Resume(F8), the pointer always jump to start of StartDefaultTask function.My functions are working correctly in another project. Anyone can help my fix this bug?Many thanks, HieuHere is my task define:osThreadId defaultTaskHandHandle; osThreadId MQTTTaskHandHandle; osThreadId PubTaskHandHandle; osThreadId UpdateTaskHandle; void StartDefaultTask(void const * argument); //void StartDefaultTask(void * argument); /* USER CODE BEGIN PFP */ void MQTTTask(void *client); void PubTask(void *argument); void SyncTask(void *argument); osThreadDef(defaultTaskHand, StartDefaultTask, osPriorityNormal, 0, 4096); defaultTaskHandHandle = osThreadCreate(osThread(defaultTaskHand), NULL); osThreadDef(MQTTThread, MQTTTask, osPriorityNormal, 0, 1024); MQTTTaskHandHandle = osThreadCreate(osThread(MQTTThread), clie