Solved

..

Interrupt 1 threshold. Default value: 000 00001 LSb = 16 mg @ FS = ±2 g1 LSb = 32 mg @ FS = ±4 g1 LSb = 62 mg @ FS = ±8 g1 LSb = 186 mg @ FS = ±16 g what is this ????? Please Help........

I cannot get the CAN bus CAN1_RX0 interrupt to fire. I have two other development boards (STM32429i-EVAL1 and STM32373C-eval) that both work correctly. I am using the same code in each setup thru the ST MX and IDE. The Eval boards have built in CAN interface, so on the Nucleo board I am using a CAN adapter.I have a USB CAN device to receive and send CAN messages to boards. I also have a CAN logic analyzer verifying messages.So on the NUCLEO board I am able to verify the CAN message being received is correct on the port PINS PB8 and PB9. tried configuring CAN1_RX to PA11 also, same result.I have gone back and forth between boards and project trying to find a difference or reason I cannot receive the CAN interrupt on the Nucleo board!I have attached the Nucleo project. Any help would be appreciated.

..

Hello everyone,I am working with the board STM32F446RE with SX1261 on mbed os.SITUATION: I want to measure the time difference between the send moment and the receive moment of a packet (transmitted by LoRa). Basically, when I send packet A (send time) from 1st board, the second board receives the packet and immediately responds back. 1st board receives (receive time) the response. I measured this period 30 times to get the time difference but this value kept increasing/decreasing until it reached a point before dropping/rocketing.SET UP: I used timer 2 with 90MHz clock frequency. Two boards are at fixed distance.WHAT I HAVE DONE: Considering that changing measurement, I also measured the time difference between the receive time and the response time on the 2nd board with timer 2. The same dropping/rocketing still occurred.QUESTION: What might be the cause of this change? I suspect it might be the timer that has a rollover.The pattern is something as below. “Dedicated�? means the 1st b

We need dedicated drivers for Flash memory Read and Write operations dedicatedly. In example project given the just Read a 32-bit word data only. If we want to read the entire page or part of the page data and verification is there any driver layer available, please share to us.

Hi team,I used STM32WB15CCU6 in my project for Voltage and sensing. I already used all analog pin for sensing.I need one SPI and one UART communications channels.Can you please suggest which pins can I used for SPI and UART.I request please share the schematic or pin mapping details.Thanks & RegardsRajkumar ChaurasiyaMob. No. 8591217827

Hi all,is it possible to connect an external antenna to the X-NUCLEO-NFC06A1, if possible, where?Thanks,D.

Hello.I try to use ADC with STM32H743II. The problem is that the calibration flag is not reset.//ADC1 RCC->AHB1ENR |= RCC_AHB1ENR_ADC12EN;   //Exit DEEP Sleep ADC1->CR = 0; while(ADC1->CR != 0) { ADC1->CR = 0; };   //Enable LDO ADC1->CR = ADC_CR_ADVREGEN; //dump delay, for LDO startup for(uint32_t i=0; i<0x10000; i++){ __NOP(); }; //Start CAL ADC1->CR |= ADC_CR_ADCAL; while(ADC1->CR & ADC_CR_ADCAL){__NOP();}; //Program stop here foreverThis code worked in another project. If remove the calibration, then the ADC works (I use 2 regular channel with DMA).Why can't the flag ADC_CR_CAL be reset?

Hello, Is there a lora library which supports the lora specification 1.1 available?What I found are 1.0.3 and 1.0.4. But I am looking for 1.1 too.Anybody can helps?

Hi!I am looking for a brushed DC-motor ±12V controller for higher currents, typically 25A-30A. I have checked the ST products Evaluation & Development Boards for Brushed Motors - STMicroelectronics but it seems the highest current available is 2.5 A. However, it does not need to be a complete dev board.I am considering to design something similar to Sabertooth 2x32 regenerative dual motor driver (dimensionengineering.com) that I can control with PWM from a STM32 MCU.Any hints?Thanks in advance

I want to understand how I could convert the sensor data on the box into real-time position tracking. The tracking is periodic linear movement in the y-direction going from a range max of 15/16 feet and back to 0. Are there any good resources or git-hub repos I can tap into?

Hello STM32U5 community,I was making a few attemps with my B-U585I-IOT02A demo board and TF-M. I am afraid I have irreversibly locked the MCU.Here is what I did:run regression.shset RDP level 1 with the Programmer despite the warnings, because I forgot that regression.sh had erased the Secure and NSecure applications.Now I fail to reconnect with the MCU by any means. What can I do? TZEN/RDP regression with boot from RSS? AN5347 says "a small rework" must be done. I would appreciate a step by step instruction.Regards.

In Bus -off condition , the ECU(node) disconnects from the CAN bus.So how it monitors the transfer and receiving of the message signal in CAN bus until Bus -off recovery stage is received.

..

The STM32F070RBT has Hardware Flow Control for RS485, with DEAT, DEDT and DEM bits in USART_CR1 and USART_CR3 registers.How do we identify which series of ICs have these features easily? Is it a particular series or type? The STM32F4 IC we are currently using does not have this option however it is not highlighted as different on the datasheets.

Hi all!I am testing the audio configuration for the stm32mp156C-Dk2, with lastest demo(4.0.1-openstlinux-5.15-yocto-kirkstone-mp1-v22.06.15).I followed the sound card configuration [tutorial](https://wiki.st.com/stm32mpu/wiki/Soundcard_configuration) and I can't configurate correctly somes controls.E.g (Analog Playback Volume)root@stm32mp1:~# amixer -c STM32MP15DK cset name='Analog Playback Volume' '204','204' amixer: Control sysdefault:0 element write error: Invalid argument   root@stm32mp1:~# amixer -c STM32MP15DK cset name='Analog Playback Volume' '100','100' numid=3,iface=MIXER,name='Analog Playback Volume' ; type=INTEGER,access=rw---R--,values=2,min=0,max=228,step=0 : values=100,100 | dBscale-min=-102.00dB,step=0.50dB,mute=0In this case, the max argument is 228 but when I try it with the value 204, it says: "invalid argument" but with other lower value it works...This also happen with others controls.What is the reason for this to happen?Regards!Thanks!

..

Hello,I am looking to use the NUCLEO-H7A3ZI-Q, which utilizes a STM32H7A3ZI MCU. It has the following memory specifications:2MBytes of Flash1376 kBytes of SRAMI am looking to do the following things on my product:1) LCD Display (480x272 resolution), potentially with animations (animations TBD. For this question, assume we are using animations)2) CAN communication3) Basic GPIO signalingMy goal is to minimize PCB cost, so I am trying to see if I can get away with no additional, external RAM/Flash. I am trying to determine if that is possible, but want to confirm my logic.For the SRAM, it needs to be able to display each pixel of the full 480x272 resolution. If we assume 1 frame buffer (no animation) and a 24 bit depth (RBG888), then the RAM requirement is:480 x 272 x 24 / 8 / 1000 = 391.68 kBytesIf I want to do animations (Basic TouchGFX screen transitions. Not anything fancier than that), then an additional frame buffer would be needed. Therefore, the needed SRAM is:480 x 272 x 24 / 8 /

Dear All,I have a nucleo-l010rb board and I am generating a code to read 24C512 EEPROM on I2C. I have tried CubeMX Firmware Version 1.12.1 and 1.11.3. When I generate the code for the IDE default PA9 and PA10 following is the HAL_I2C_MspInit function generated in stm32l0xx_hal_msp.c file.void HAL_I2C_MspInit(I2C_HandleTypeDef* hi2c) { GPIO_InitTypeDef GPIO_InitStruct = {0}; if(hi2c->Instance==I2C1) { /* USER CODE BEGIN I2C1_MspInit 0 */   /* USER CODE END I2C1_MspInit 0 */   __HAL_RCC_GPIOA_CLK_ENABLE(); /**I2C1 GPIO Configuration PA9 ------> I2C1_SCL PA10 ------> I2C1_SDA */ GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10; GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; GPIO_InitStruct.Alternate = GPIO_AF6_I2C1; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);   /* Peripheral clock enable */ __HAL_RCC_I2C1_CLK_ENABLE(); /* USER CODE BEGIN I2C1_MspInit 1 */   /* USER

Hi,I am new to STM32 and the Signing Tool and I'm trying to sign using a key from an HSM (nitrokey) but i get the following error:"Error loading pkcs#11 module functions".I run the following on Ubuntu 20.04:STM32MP_SigningTool_CLI --binary-image [path to stm32 file] --algorithm 2 --module /usr/lib/x86_64-linux-gnu/engines-1.1/libpkcs11.so --key-index 0x0 --slot-index 0x0 --password 123456 --output ./signed.stm32Any help appreciated!ThanksDoug

We teach using the STM32L476G Discovery kit Board. We have been using STMCubeMX 5.6.0 and Libraries 15.1. We want to migrate to current versions (6.6.0 and 17.2) but all of out programs that use the LCD controller fail. After some detective work, the bug appears between versions 6.2 ands 6.3. There is a file called stm32l4xx_hal_msp.c that is generated and some new code has been added:/** Initializes the peripherals clock */ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_RTC; if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { Error_Handler(); }It turns out that this code was moved from main.c to stm32l4xx_hal_msp.c and in moving it one line of code was dropped. PeriphClkInit.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;Without this line of code, the LCD/RTC clock selection is none. That's why nothing works. There is a workaround since there is a user area where this code can be placed. But - it is still a bug.How do I report this kind of bug and either get it ad

After enabling "generate peripheral initialization as a pair of '.c/.h' files per peripheral" under Project manager > Code generator > Generated files, everything stops working, including debugging log also does not show up in my tera term.How to regenerate this problem: (stm32wb55 ) Select the BLE_Custom example from the libraryAdd FreeRTOS in the ioc. file (Remember to set the TOTAL_HEAP_SIZE to 20480, Enable     USE_NEWLIB_REENTRANT  , change your SYS timebase source to TIM17) Go to Project manager > Code generator > Generated filesEnable "generate peripheral initialization as a pair of '.c/.h' files per peripheral" * There will be no issue if I did not enable the "generate peripheral initialization as a pair of '.c/.h' files per peripheral" but I feel that it is messy if I don't enable it.

In STM32CubeMX clock schematic and in the clock schematic of the reference manual CK_PWR is mentioned. It is never explained what it does and what it is for.I'd like to know what it is for and how it affects current consumption (since it is before the AHB prescaler).

..