Solved

Hello Team,                I am finding the sensor which have the up to 15 meter range.                                i am using this sensor in my water level detection project so according to suggest me the sensor.  Thanks and regard'sASHISH K.

Yesterday, I have flashed faulty code to my STM32, and now I can't connect to it via ST-Link or the UART bootloader. I've tried using STM32 ST-Link Utility and STM32CubeProgrammer, but neither works. How can I erase the flash memory? Do I need to buy a new chip?i using stm32f103c8t6

Hi, I'm trying to connect a high speed ADC to an STM32F7. I have chained two timers to generate the necessary convert and read pulses to the ADC. Its output is 16 bits that are all connected to the same gpio block. However I would also like to setup a DMA (double buffered) transfer from GPIO input register to memory that is timed from the timer. The timer that generates the samples from the ADC to the gpio input is configured as a one shot timer with an output channel, in this case TIM1_CH1. Config for the timer is: m_rd_timer.Instance = TIM1; m_rd_timer.Init.Prescaler = prescaler; m_rd_timer.Init.CounterMode = TIM_COUNTERMODE_UP; m_rd_timer.Init.Period = period_len; m_rd_timer.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; m_rd_timer.Init.RepetitionCounter = 8-1; m_rd_timer.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_ENABLE; ocConfig.OCMode = TIM_OCMODE_PWM2; ocConfig.Pulse = pulse_len; ocConfig.OCPolarity = TIM_OCPOLARITY_LOW; ocConfig.OCNPolarity = TIM_OCNPOLARITY_LOW; ocConfig.O

Hello,I wanna read an external ADC.The ADC has following serial process conditions:1. Get a CNV signal by µC2. Convert and send BUSY=HIGH to µC3. After Convert send BUSY=LOW to µC4. µC send SCK to ADC, then ADC send data and is running as long as it gets SCK signalsThat causes, that I cannot run my SPI DMA communication in circular mode, because I have to run the CNV and BUSY process first and always de-/activate SPI (the SCK signal) after it. So I have choosen the normal mode.But the thing is I want to run the SPI communication fully at the background, also the CNV and BUSY process, that my main while function does not block the regular SPI and Convert process. This is what should be fast always. And at the main while loop I can choose, if I output the data at 100 ms rate or whatever.So I had the idea to use TIM6´s Callback function to run the CNV/BUSY/DMA-Receive-call at the background, wile the DMA-call also runs at the background.(I have tested the DMA Communication at the main whi

I am working with an ST25R3916b, utilizing the RFAL library. I am trying to work with a card that does not always send back a CRC over NFC, so I need to be able to disable the CRC RX checks dynamically. My txrx function looks like:static int st25r_nfca_rxtx_rf(const struct device *dev, uint8_t *tx_data, uint16_t tx_bitlen, uint8_t *rx_data, uint16_t rx_size, uint16_t *rx_bitlen) { LOG_DBG("Transmitting and receiving using RF interface"); ReturnCode ret; rfalTransceiveContext ctx = { .txBuf = tx_data, .txBufLen = tx_bitlen, .rxBuf = rx_data, .rxBufLen = rx_size, .rxRcvdLen = rx_bitlen, .flags = (uint32_t)((NFC_ST25R_DATA(dev)->tx_crc) ? RFAL_TXRX_FLAGS_CRC_TX_AUTO : RFAL_TXRX_FLAGS_CRC_TX_MANUAL) | (uint32_t)((NFC_ST25R_DATA(dev)->rx_crc_keep) ? RFAL_TXRX_FLAGS_CRC_RX_KEEP : RFAL_TXRX_FLAGS_CRC_RX_REMV) | (uint32_t)RFAL_TXRX_FLAGS_NFCIP1_OFF | (uint32_t)RFAL_TXRX_FLAGS_AGC_ON | (uint32_t)RFAL_TXRX_FLAGS_NFCV_FLAG_AUTO | (uint

Hi,I am currently working with the X-NUCLEO-NFC08A1 as reader another PCB with a stm32 microcontroller and a ST25DV04K tag. I don't have access to the source code of the board with the tag but i know the used protocol to interact with it.I got everything running but sometimes it seems as if the HOST_PUT_MSG flag is set before the response is fully written. I poll for the response to be written with something like this:uint8_t waitCounter = 0; /* wait for response to be written by tag. */ while (ftmGetMessageOwner() != FTM_MESSAGE_PEER && waitCounter <= FTM_MAX_RESPONSE_WAIT_TIME) { platformDelay(1); waitCounter++; } if(waitCounter == FTM_MAX_RESPONSE_WAIT_TIME){ platformLog("Tag response timeout.\n"); return true; }But with debugging I found out that sometimes the command sent before is still in the mailbox when the message owner already changed and thus being read instead of the answer.So my question is: When is the HOST_PUT_MSG bit put? Is it put by the user or

I am using a NUCLEO-F767ZI Board.Previously I have not used or configured any GPIO. Then I used CubeMX to reconfigure 3 Pins to Inputs with Pull-Down like this: if (HAL_GPIO_ReadPin(button_uncouple_GPIO_Port, button_uncouple_Pin) == GPIO_PIN_SET) {In the code I was using a basic check like the one above. After flashing the new code to the board. The board no longer appeared as a usb device. Instead the system log reportedkernel: usb usb1-port1: over-current conditionI was able to recover access to the board by powering the board using an external 5v power supply to the E5V Port and GND. Then I could flash an older version of my code without the GPIO configured and everything is working fine again, also without the external power supply.I do not understand why the reconfiguration of the pins as input pull-down lead to this. This should not result in an increase of current usage?

Hi,I want to download an old version 3.0.1 of Nano Edge AI studio but I could not find it from the website. It directly download the new version 4.5.0. How can I reach the version 3.0.1?

Hello STM community,I have built and assembled a custom PCB board with an STM32U083CC on it. I have made 5 boards, after the first two did not work, I only populated the minimum on the other three. However, I am unable to debug or event connect to it through any means I tried, and I fear I have a systematic error in my schematic or workflow.I connect to the target over SWD, using a NUCLEO-WL55JC1 board on which I have removed both JP1 and JP7, as well as attached directly to the JP8 headers. I have independently tried using a picoprobe, which gave the same result: Seemingly no answer from the MCU, as both programs report a timeout when trying to communicate with the target.To connect I use the `st-link` utility on linux, and have attached the NUCLEO-WL55JC1 via usb.I have verified the following:- Proper MCU placement wrt to pin numbering- No shorts during soldering or after- I read through the guide for hardware development for this MCU and have the appropriate capacitors on the power

Hi there,I'm using STM32MP257F-DK and bringing up by FlashLayout_emmc_stm32mp257f-dk-ca35tdcid-ostl-optee.tsv.I found there is no wifi/bt device by command ifconfig. It's only showing below. root@stm32mp2:/etc# ifconfigend0 Link encap:Ethernet HWaddr 10:E7:7A:E3:AA:F4inet6 addr: fe80::12e7:7aff:fee3:aaf4/64 Scope:LinkUP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1RX packets:0 errors:0 dropped:0 overruns:0 frame:0TX packets:102 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:0 (0.0 B) TX bytes:28558 (27.8 KiB)Interrupt:58lo Link encap:Local Loopbackinet addr:127.0.0.1 Mask:255.0.0.0inet6 addr: ::1/128 Scope:HostUP LOOPBACK RUNNING MTU:65536 Metric:1RX packets:130 errors:0 dropped:0 overruns:0 frame:0TX packets:130 errors:0 dropped:0 overruns:0 carrier:0collisions:0 txqueuelen:1000RX bytes:9985 (9.7 KiB) TX bytes:9985 (9.7 KiB)usb0 Link encap:Ethernet HWaddr DA:74:68:4A:DE:B0UP BROADCAST MULTICAST MTU:1500 Metric:1RX packets:0 errors:0 dropped:0 overruns

Hello.I'm using Riverdi board.This board uses STM32H757XIH6 .I used FATFS R0.12c with uSD and USB-MassStorage in Unicode mode When mount uSD and then USB I noticed that FatFs[0] is overwritten.  

Hello, I get the following warning: at the suggested site I cannot find an option to tick. What can I do? Regards Alexander

Hi Team,We are using STM32G431RBT6, we have tested the ADC1 for PA3 i.e. Channel4 with external Vref 3.3 and VDDA 3.3 with 12-bit selection and the reading we are getting with 5 to 10 counts fluctuations we are seeing but when we have changed to internal voltage ref selection for 2.048 then the PA3 i.e. Channel4 is fluctuating more than 1000 counts! but it works fine for PA0!VDDA remains same 3.3v for both our internal and external voltage.Please suggest us how to resolve this?? Thanks 

Hi everyone,I'm currently designing a custom board based on the STM32F722, and I came across something I need clarification on.According to the STM32F722 datasheet, there is no device listed in the UFBGA176+25 package. However, when searching online (Buy STM32F722IEK6 - ST Online Store), I found a part labelled STM32F722IEK6.Unfortunately, I can't seem to find a dedicated pinout or ballout diagram for this specific part.I'm assuming that since the package is UFBGA176+25, the pinout would be similar (or identical) to that of the STM32F723xx series with the same package.If that assumption is correct, would it also mean that the power supply scheme should follow the STM32F723 diagrams? (i.e., including pins like VDD12OTGHS, OTG_HS_REXT, etc., which are not shown in the STM32F722 typical power scheme?)I just want to make sure before proceeding with the design.If anyone has worked with the STM32F722IEK6 in UFBGA176+25 or can confirm if it mirrors the STM32F723xx pinout and power supply desi

Hello,i have problems to install the ST MC Workbench (x-cube-mcsdk_5.3.3). If i want to install the file, i get the an error:Error Opening file for writing:C:ßProgram Files(x86)\STMicroelectronics\MC_SDK_5.3.3\Middlewares\ST\MotorControl\MotorControl_Config.xmlCan anybody help me?

Hi,I'm looking for an STM32 flashing tool that runs on ARM Linux for use on an embedded board. In our setup, I have a processor and an STM32G491RET microcontroller connected via I2C. Now I need a command-line tool that can run on the processor to flash the MCU over I2C. Is there any tool available that supports this use case?  

Hello,When I launch CubeMX from the CubeIDE via New Project the UI of CubeMX appears unusual. The sidebars are "Windows XP style" and there are other graphical anomalies. When I launch CubeMX from VScode the UI appears normal. The two screenshots I posted show the differences. I am wondering if maybe there is some setting in CubeIDE that may have caused this.Thanks  

Hi,In the past we've always produced 'release' firmware for STM32F4 which checks the RDP level (memory read / debug protection) at boot up, and ensures it's automatically set to RDP1 (read protection enabled). This ensures that our code can't be easily read out of the device by 3rd parties, but if necessary I can connect a debugger, reset the option bytes (which performs a full erase), and reprogram the chip. This works well. We also have our own secure bootloader which deals with encrypted firmware updates and which is well supported by our production equipment and staff.I'm now working on porting a design to STM32H523, which has an enormously more complicated security system.What I've figured out so far is that:- I think the closest behaviour it's capable of would be to have TrustZone disabled, to set a password for Debug Authentication, and to have the product in the "CLOSED" state when shipped.- This would ensure the product is read protected, but it can be fully erased and set bac

Hello, I have downloaded a library containing two files: the .h file and the .c  file: I used drag and drop and dropped the folder into the driver folder of my project. I selected them to be a reference and a relative path. Then I selected the compiler include path:  and the linker pathThe IDE is showing the resource correctly linked to the project: when I build the project I still get the error message: What is wrong with my approach?How do I set the paths correctly?As a suggestion: I have found many users struggling with this. I would like to recommend a dialog for dropping a folder into the project with predefined links to the new folder.Regards Alexander 

Hi, i am trying to connect the nrf54L15 with the VL53L4CD sensor. I am having trouble with library and the code. Struggling with connecting the nrf54L15 to the sensor in the different libraries. Are you able to share the different register adresses for the VL53L4CD sensor? Do you have an examples using the nrf54L15 and or device tree with the VL53L4CD?

In instances where they don't answer the question, or where they answer it incorrectly, I have been reporting these. Should I keep doing so?Does the ST community have a stance on whether or not AI-generated reponses are allowed? Is that stance in the guidelines and if not, can we put it there?For example, clearly this is ChatGPT generated nonsense:Another one, same thread even.At first glance it seems like these answer the question, but they fall apart under inspection. These two are obvious, some are less so.

I am using output compare with TIM3 on a STM32H755 I am able to use Output Compare to generate a single pulse on pin PC7 using TIM3, Channel 2.I am using Active Level on Match.I call HAL_TIM_OC_Start(&htim3, TIM_CHANNEL_2) onceAfter 0.5s, it detects a match (which is good), and my pin drops and stays low (I have negative polarity set).However,  I can find no way to restart the process.I have tried resetting the timer calling HAL_TIM_OC_Stop(&htim3, TIM_CHANNEL_2) and HAL_TIM_OC_Start(&htim3, TIM_CHANNEL_2), but the pin remains low. I've even tried calling the initialisation code again. I assume I am missing something fundamental here? Settings: (see screen shot attached )Auto-reload preload: DisableMode: Active Level on MatchOutput Compare Preload: DisableCH Polarity: Low 

Hello everyone, I am a first-year university student. I am developing a GUI application on the STM32U585 using TouchGFX Designer and FreeRTOS, and I have encountered some issues. Due to my lack of experience, I would like to ask for your advice on how to solve these problems. Here is my GitHub repository for the code(https://github.com/weixuna/GPDMA_AMOLED_). Device information:MCU: STM32U585CIU6RTOS: FreeRTOSGUI: TouchGFXIDE: STM32CubeIDEGPDMA enabledThe display is AMOLED, and the MCU communicates with the screen via QSPI in OCTOSPI mode.Phenomenon:I added two buttons in TouchGFX Designer.When I swipe to switch to a page (Screen) with two buttons, the program sometimes crashes and enters a HardFault.The crash happens during or after the page transition animation.If I add transition animations such as Cover, Wipe, or Block, there will be screen corruption (garbled display). If

Is there any information for the STM32H735-DK on how to configure the S70KL128 HyperRAM to work?Unfortunately, there's no source code for the binary demo from ST, so I'm forced to try to get the HyperRAM working somehow.And the forums only provide information about problems when trying to run it in memory-mapped mode.So far, I haven't been able to read or write a single byte because:- The access times, latency times, and the clock in the STM32H7 must be set correctly for the HyperRAM to be accessible at all.- The settings in the HyperRAM itself also need to be configured (DDR/DTR, drive strength, latency, burst length).When creating a new project with the default values ​​in the STM32CubeIDE for the evaluation board, adjust the octospi clock to 100MHz (PLL2R) and attempting to read the hyperram with the debugger, the only output is:Could not halt device (18)Failed to read all registers from targetTarget is not responding, retrying...Target is not responding, retrying...When importing p

I am working on a custom board and I have noticed that whenever the device resets, it becomes unresponsive.The reset causes that hang the microcontroller:Calling NVIC_SystemReset from firmwareHaving firmware stuck and receiving a signal from IWDGManually grounding the NRST pin.The debugger shows that the program starts running in a lop at addresses 0x1FFF2XXX, which would be a RAM stack, I suppose?..My FW memory map looks like this:MEMORY { RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 64K RAM2 (xrw) : ORIGIN = 0x10000000, LENGTH = 16K BOOT (rx) : ORIGIN = 0x08000000, LENGTH = __boot_size FLASH (rx) : ORIGIN = 0x08000000+LENGTH(BOOT), LENGTH = __program_size FLASH2 (rx) : ORIGIN = ORIGIN(FLASH)+LENGTH(FLASH), LENGTH = __program_size DATA (rx) : ORIGIN = ORIGIN(FLASH2)+LENGTH(FLASH2), LENGTH = __data_size }My USER_VECT_TAB_ADDRESS is defined and VECT_TAB_OFFSET is non-zero due to isr_vector not being at the beginning of the FLASH region.So far I tried downloading a dummy firmware wi