Solved

Hello,for an upcoming project I am searching for a low-power microcontroller with a rich peripheral set and the possibility to sample low frequency signals in the range from -0.4V to 3.6V .As far as I have looked it up I will have no chance realising this project with a STM32L4x but maybe somebody has a good solution suggestion for me on that matter.I preferably want to avoid an extra ADC chip.best regardsBenjamin

I have a design with STC3115AIQT as in picture:VBAT and GND are connected to positive and negative terminals of a Li-Ion battery, respectively.When the device is powered-off 3V_L is connected to GND. In this condition VIN pin is sinking 3mA of current, i.e. Voltage across R15 is 3V.Why is it so abnormally high compared to the value stated in datasheet (1µA)? How can I fix it?

HiI have been trying to get USB HOST MSC working on the NUCLEO-H743ZI and cannot get past one point. I have reduced my test to a new test project with auto-generated code via STm32CubeIDE with the following settings.FATFS enabled for USB only with USBH instance = "USBH Host MSC FS" and VOLUMES increased to 2USB_HOST set to FS Mass Storage Host Class only and VBUS driven by GPIOUSB_OTG_FS in Host_Only mode with VBUS sensing on and SOF activated (although I tried these off as well.USB Clock confirmed as 48MhzThe auto-generated code gives me the basics, and I have added a VBUS enable after initialising everything, and I can see the LED light as well as measure 5V on the USB power lines. /* Initialize all configured peripherals */ MX_GPIO_Init(); MX_ETH_Init(); MX_USART3_UART_Init(); MX_FATFS_Init(); MX_USB_HOST_Init(); /* USER CODE BEGIN 2 */   MX_DriverVbusFS(0); // Turn on USB power   /* USER CODE END 2 */With that as the basics, I can see that the USBH_UserProcess is

I've been working on making my SD SDIO card access non blocking. My implementation is a derivative from the standard ST SDIO SD driver (stm324xg_eval_sdio_sd).I'm using Protothreads (basically a state machine) to make the SD SDIO calls non-blocking and allow the program execution to continue while I'm waiting for the operations to complete. For some unknown reason, and I've not been able to identify the cause, when I continue with the program execution, I get a timeout error from the SDIO interface. But when I block and wait for the result all is fine. This is what I currently have:static PT_THREAD(sd_CMDResponse1Error_V(struct pt* Thread_PS, uint8_t CMD_U8, SD_Error* SDResult_PE)) { static uint32_t Status_U32; uint32_t Response_U32; static uint32_t Timeout_U32;   // Begin the thread PT_BEGIN(Thread_PS);   // Initialise the result *SDResult_PE = SD_OK;   // Initialise the timeout Timeout_U32 = SDIO_CMD0TIMEOUT;   while (1) { // Get the status Status_U

Hi,I am only a bit familiar with embedded linux. I will develop a demo project with STM32MP157C-DK2 with C language:on M4 side, a sensor(BME280) and a vantilator (5v) are connected. Sensor is to read periodically and three numerical values( temp, humidity, pressure) will be send to A7 sideon A7 side a QT application will receive these three values and display them continuosly. Over this QT application, the user will be able to send on or off command for vantilator to M4.M4 will receive this command and then will start or stop the vantilator.At first, I should say, I played a bit with the board, did all the work which is called getting started with DK2 (https://wiki.st.com). Then I saw an article in bootlin about using BME280 sensor. But this article doesnt help me because it explains how to read the sensor from A7 (linux side). However I will read the sensor from M4 side.Honestly, I don't know how my roadmap will be.I mean where to start and which mechanisms, middlewares, package (dev

Hi all,Dear all ST's expert, somebody help me out, Thank you very much.An errors occurred while compiling, see below:assembler code:build result:​IDE: SPC5 Studio, version: 5.8.1Compiler: FreeGCC with VLE support or Hightec Pro

HII've already run this command​Continue to run​root@stm32mp1:~# /usr/share/examples/opengl/hellowindow/hellowindowqt.qpa.input: X-less xkbcommon not available, not performing key mappingCould not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)Could not queue DRM page flip on screen DSI1 (Device or resource busy)does not help!What can be the Issue here?​I read this post https://community.st.com/s/global-search/Could%20not%20queue%20DRM%20page%20flip%20on%20screen%20DSI1%20%28Permission%20denied%29​

Hi everyone,I am using the Nucleo-WB55RG to try and fully erase/program the flash memory. However, when the FLASH_MassErase() function is called in stm32wbxx_hal_flash_ex.c, a hard fault exception occurs. I believe this has to do with trying to erase the secure memory only accessible through CPU2. When I try to boot up CPU2 (set C2BOOT pin) I receive a PGSERR flag in the FLASH_C2SR register. This has been extremely inconvenient that for the entire flash to be erased, you need execute from CPU2 and the boot process is not exactly straight forward. Are there any suggestions on how to gain access to CPU2 and perform the mass erase function? Thanks.Steve

Lets say I need to separate module, one will contain the pcb with mpu and other IC, the second will contain a touchscreen display and sensors. The modules are 2 meters apart. What should I use hdmi or mipi? How do I send mipi over distance?

I refer to the source code for "Model UI Demo 1 TouchGFX".I would like to enlarge the PieChart, but I can't figure out how to do it. In the GraphView::setupScreen function I modified the values for center, height and width.// GraphView.cpp - GraphView::setupScreen pieChartX = 0; pieChartY = -16; donutX = pieChartX; donutY = 34; pieChart.setPosition(pieChartX, pieChartY, 300, 300); /* <- modified */ pieChart.setCenter(150, 150); /* <- modified */ pieChart.setPieChart(0, 0, 0, 0); pieChart.recalculatePieChart();However, the PieChart radius does not change.how to do ?//Antonello

Can anyone point me to an example on how to use bluetooth for this discovery board? Will it be possible to pair to two bluetooth sensors at the same time?

How to draw a dotted rectangle while dragging to select a part of the interface?

Hello,I am working with STM32F413H discovery board, it was working fine with inbuilt debugger but this reference board raising error like "Error in initializing ST-LINK error" while flashing.After this I got better answer from ST employee that : "If code on your device breaks the debug interface pins or powers down it won't be connectable.Try "Connect Under Reset" optionsTry pulling BOOT0 High so your code in FLASH doesn't run."Here, can I make BOOT0 pin high while flashing right ? and after flashing can BOOT0 pin make it low? and can one elaborate "Connect Under Reset" optionsIDE : STM32cube IDEdevelopment board :STM32F413HBest Regards, Nitish

External interrupt errata?I have setup EXTI_Line12 and EXTI_Line14 to generate en interrupt.But the EXTI15_10_IRQHandler() fails to execute a second interrupt if it happens too close to the first interrupt.But it seems only happen when I use bit-banding to check and clear the bits in the EXTI->PR register. If I access the EXTI->PR directly at the normal address it does not happen.Is this a known problem?I read something similar in another chip errata (but on an STM8):When an interrupt handler starts executing a service routine and an external interrupt (EXTI) request is pending or arrives during the same cycle, the external interrupt is not executed.void EXTI15_10_IRQHandler(void) { GPIO_SetBits(GPIOB, GPIO_Pin_10); // Toggle PB10 to show we are entering the interrupt GPIO_ResetBits(GPIOB, GPIO_Pin_10); // NOTE: // PERIPH_GET_BIT is a macro that reads one bit using bit-banding // PERIPH_SET_BIT is a macro that sets a bit using bit-banding #ifdef USE_BIT_BANDING if

I'm having trouble getting the ADC on a STM32L476VGT6 discovery board to work. If I run by configuration code then click the ADSTART bit in the debugger, everything works fine. If I set the ADSTART bit in code in real time, the conversion never finishes. Anyone have a simple, single-channel, single-conversion ADC example?

I'm trying to implement a self-test for the LSM6DSOX in Mode 1 (as in page 118 of AN5272 Rev 3). Could someone explain what the ST_X, ST_Y, ST_Z variables represent? Would Min(ST_X) be the minimum value of the 5 samples while self-test is enabled, or the minimum of all 10 samples taken? Also, I'm assuming that OUTX_, OUTY_, and OUTZ_ variables are the averages of the 5 samples for each NOST and ST case. Is that correct? If that is correct, then it looks like the pass/fail criteria is comparing the difference between NOST and ST averages to the minimum and maximum sample values. That math doesn't make sense to me. I'd appreciate some clarification - thanks!

Right now it appears we must use AC6. Will it be long before CubeIDE works?

About STM32H743VGT6Selector of STM32CubeMX show that flash size of STM32H743VGT6 is 1024K.but when i used STM32CubeProgrammer to connect it,that show flash size if 2048K。even the sector from 0x0810 0000 to 0x081f ffff can be erase and program to。so the flash size of STM32H743VGT6 is 1M or 2M？

Is there a HowTo method to program a Nucleo board? I think I inadvertently erased my board and IAR no longer see the ST-Link.I have tried the following: With IAR v8.11 and a Nucleo-H743ZI2, I opened a STM32H7 Cube GPIO example project and built it with no errors. The Download failed with Write errors in the 0x20000000 and 0x40000000 regions. I installed the latest ST-Link drivers and updated the ST-Link firmware. No improvement.I used STCubeProgrammer and it was able to read something. (I did not note which CPU, but it was flash 0x80000000 region)In IAR, I converted the output to a .hex file and wrote that to the Nucleo via STCubeProgrammer. Programmer said it worked OK.Program does not function as expected. i.e. Button->LED ON->Button->LED OFFIAR can no longer see debug probe.Verified STCubeProgrammer connects to both ST-Link and the H7 processor.Can I recover my Nucleo?Can I use IAR and the Nucleo's ST-Link?

Hello, everyone.Does touchgfx support multi-touch?Thanks in advance!

Hi,i am not able to activate TRACE SWO (Pin PB3) in CubeMX.There is a hint that for SYS_JTDO-SWO (no mode).How can i solve this?

Rev 7 of the VL6180X datasheet shows the SYSALS__INTEGRATION_PERIOD register at 0x040, however Version 2 of AN4545 changed the address of what presumably is the same register from 0x040 to 0x041. Which is it?Thanks.

..

#include <bsp/OTM8009TouchController.hpp> #include <touchgfx/transforms/TouchCalibration.hpp> extern "C" { #include "stm32f769i_discovery.h" #include "stm32f769i_discovery_ts.h" } using namespace touchgfx; using touchgfx::TouchCalibration; TouchCalibration tsCalibration; static touchgfx::Point lcdCalibPoints[3] = /* Display size is 800x480 */ { { 20, 20 }, /* 10%, 10% */ { 780, 20 }, /* 90%, 50% */ { 780, 460 }, /* 50%, 90% */ }; //calibration ADC 12 bit values static touchgfx::Point touchCalibPoints[3] = { { 200, 370 }, /* ADC values read when clicking in 80,48 */ { 3927, 341 }, /* ADC values read when clicking in 720,240 */ { 3919, 3807 }, /* ADC values read when clicking in 400,432 */ }; void OTM8009TouchController::init() { BSP_TS_Init(BSP_LCD_GetXSize(), BSP_LCD_GetYSize()); tsCalibration.setCalibrationMatrix(lcdCalibPoints, touchCalibPoints); } bool OTM8009TouchController::sampleTouch(int32_t& x, int32_t& y) { touchgfx::Point tsPos; uint8_t sta