Solved

I am trying to include the CMSIS/DSP Library into a uVision 5 Project generated by STM32CubeMX.I went to "Runtime Settings" and included checked the DSP checkbox.http://stm32f4-discovery.net/2014/10/stm32f4-fft-example/fft-enable-dsp-library-keil/In main.c I added the include line <arm_math.h>In the preprocessor settings I added the Symbol "ARM_MATH_CM4".STM32F412Re / Keil uVision 5What am I missing?The compiler throws 30 errors like:compiling main.c... C:\Keil_v5\ARM\PACK\ARM\CMSIS\5.6.0\CMSIS\DSP\Include\arm_math.h(645): warning: #47-D: incompatible redefinition of macro "__PKHBT" (declared at line 852 of "../Drivers/CMSIS/Include/cmsis_armcc.h") #define __PKHBT(ARG1, ARG2, ARG3) ( (((int32_t)(ARG1) << 0) & (int32_t)0x0000FFFF) | \ C:\Keil_v5\ARM\PACK\ARM\CMSIS\5.6.0\CMSIS\DSP\Include\arm_math.h(647): warning: #47-D: incompatible redefinition of macro "__PKHTB" (declared at line 855 of "../Drivers/CMSIS/Include/cmsis_armcc.h") #define __PKHTB(ARG1, ARG2, ARG3) ( (((

I am using the STEVAL-IDP005V1 and the terminal emulator, Putty, to output sensor data to my PC. I would like to plot the FFT data using Excel like is mentioned in page 20 of the Quick Start Guide. I have tried using the Putty configuration manager to output the full session to a log, but when I convert the log to an Excel file, all columns of the data in the serial monitor output are all placed in the first column in Excel. If I were to try to plot the data using this format, I would have to separate all 2000+ data points manually into different columns to make a graph using Excel. Is there a way to have the output data placed in multiple columns like is mentioned in the quick start guide? (Pg. 20 of the STEVAL-BFA001V1B Getting started Guide)

Can the ST-Link V3 SET program flash standalone (without PC)?As Flasher STM8 's standalone mode.(https://www.segger.com/products/production/flasher-st/models/flasher-stm8/)-----> https://www.st.com/ja/development-tools/stlink-v3set.html> The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers.Thanks for your answer.I found that"stand-alone" was not "without PC" but "not depend on evaluation board"."programming" was not "flashing" but "coding".

#include "stm32f4xx.h" // Device header   // Trying to use the General Purpose Timer (TIM2) to create a 1 second delay // Board External Crystal 8.0 MHz // Port A Pin 0 Output   // The program should output a high on GPIOA Pin 0 and delay 1 second then output low and delay 1 second.   int main(void){ RCC->AHB1ENR |= 0x00000001; //Enable Clock to PortA GPIOA->MODER |= 0x00000001; //General Purpose IO for PortA Pin 0 //TIM2 Configuration RCC->APB1ENR |= 0x00000001; Enable Clock to TIM2 TIM2->PSC = 8000-1; TIM2->ARR = 10000 - 1; TIM2->CNT = 0; TIM2->CR1 = 0x00000001; while(1){ while((!TIM2->SR & 1)){ GPIOA->ODR ^= 0x00000001; // Output high/low on Pin0 PortA } } }Would like to know how to calculate the values that should be inserted in TIM2->PSC, TIM2->ARR, and TIM2->CNT. Is there a formula to calculate the values. Also what values must be added to the registers in the above program to make it a 1 second delay.

I have searched around this forum and the internet, without finding a solution. The Alignment setting in the designer does not help. I want the text (5 digit integer) to be right justified with no leading zeroes. Latest version of ToughGFX and Cube. Thanks

 in stm32cubeMX configuration of SPI in slave mode, it asks for user parameter input for clk prescaler, which then derives the clk rate. My understanding for SPI operated in SLAVE mode is that the master end, instead of the slave end, generates the clock.Is there a way to better understand the purpose of this setting, highlighted in the screenshot? Thanks.

Good day.I use devboard NFC06A1 with Nucleo-L053R8. Project from STM32CubeExpansion_NFC6_V1.0.0.All works fine - via SPI. But when i choose i2C - i have a problemI changed resistorto select i2cadd pull up resistor R116 and R117Add define RFAL_USE_I2C 4. change  //HAL_NVIC_SetPriority(I2C1_EV_IRQn, 5, 5);  //HAL_NVIC_EnableIRQ(I2C1_EV_IRQn); HAL_NVIC_SetPriority(I2C1_IRQn, 0, 1);  HAL_NVIC_EnableIRQ(I2C1_IRQn);Device was crash when call  I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT); in stm32l0xx_hal_i2c.cMCU freez in startup_stm32l053xx.s I2C1_IRQHandler I2C2_IRQHandler SPI1_IRQHandler SPI2_IRQHandler USART1_IRQHandler USART2_IRQHandler RNG_LPUART1_IRQHandler LCD_IRQHandler USB_IRQHandler   B . ;crash in current line   ENDP   ALIGNWhat a mistake here ?

I have configured 5 interrupts on EXTI line.....It works fine when I operate one at a time but misses out one interrupt when operated simultaneously.....Following is my GPIO configuration:- void MX_GPIO_Init(void){ GPIO_InitTypeDef GPIO_InitStruct; /* GPIO Ports Clock Enable */ __HAL_RCC_GPIOC_CLK_ENABLE(); __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOA_CLK_ENABLE(); __HAL_RCC_GPIOB_CLK_ENABLE(); /*Configure Input GPIO pins */ GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2; GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;  GPIO_InitStruct.Pull = GPIO_PULLUP; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); GPIO_InitStruct.Pin = GPIO_PIN_3|GPIO_PIN_4; GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;  GPIO_InitStruct.Pull = GPIO_PULLUP;  HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); /* EXTI interrupt init*/  HAL_NVIC_SetPriority(EXTI0_IRQn, 0, 1);  HAL_NVIC_EnableIRQ(EXTI0_IRQn);&nbs

if stm32cudeide can view the bootloader and update the bootloader of MCU that is already writed by the vendor, like external oscillator or some other options ?i have already installing the STM32CubeIDE, STM32CubeMX and STM32CubeProgrammer. is there other softwares to help to develop?

Hello,I'm trying to get used with the HAL APIs by doing an exercises with USART of the mentioned board. The exercise is a simple one in which I try to send a character from my PC terminal using Tera Term and if this character is 'a' I want the MCU on the board to light up the user LED.I have configured USART2 module with CubeMx. The generated configuration code for the USART2 module is this:static void MX_USART2_UART_Init(void) {   /* USER CODE BEGIN USART2_Init 0 */   /* USER CODE END USART2_Init 0 */   /* USER CODE BEGIN USART2_Init 1 */   /* USER CODE END USART2_Init 1 */ huart2.Instance = USART2; huart2.Init.BaudRate = 115200; huart2.Init.WordLength = UART_WORDLENGTH_8B; huart2.Init.StopBits = UART_STOPBITS_1; huart2.Init.Parity = UART_PARITY_NONE; huart2.Init.Mode = UART_MODE_TX_RX; huart2.Init.HwFlowCtl = UART_HWCONTROL_NONE; huart2.Init.OverSampling = UART_OVERSAMPLING_16; if (HAL_UART_Init(&huart2) != HAL_OK) { Error_Handler(); } /* USER

The H747I-DISCO specs say 2MB Flash and 1MB RAM. From that, I am trying to understand what the start addresses of both areas are.I see that for both processors (M7 and M4) two .ld files get created:STM32H..._FLASH.ld and STM32..._RAM.ld, for a new STM32 project, with default peripheral settings, generated by CubeIDE 1.1 with CubeMX 5.4In the FLASH file, I see a MEMORY structure that contains{ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 1024K RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K }My questions:1) If 0x08000000 is in fact the start address of FLASH, why is the length only 1024K. Similarly for RAM - if 0x20000000 is the start address, why is the length 128K.More to the point, if I change the LENGTH values to 2048 and 1024 to correspond to what is supposedly on the board, is that valid, and is that the way to use all memory available?2) Why is there a separate RAM.ld file, which has completely different values for FLASH and RAM:MEMO

Hello.I cannot use Ethernet with my 2 weeks old NUCLEO-F767ZI (chip version Z).Probably the LAN8742A does not work properly anymore.After initilization I perform a check: if (HAL_ETH_ReadPHYRegister(&heth, PHY_BSR, &regvalue)==HAL_OK) { if (regvalue&0x04) { // cable connected, but with this board never reached ... } }No LED of the connector is active.The software works on other boards. (Latest FW, etc.)Is there a chance to rescue the board?Thank you Joerg

Hello Community,I have developed an firmware on STM32f746zgt6 MCU. Currently , I'm unable to buy STM32f746zgt6 Online.So, can I use another STM32f746 series MCU instead?If, yes can you please suggest me one.I couldn't make any changes to my firmware as well. so the MCU supposed to work on same firmware.Thanks in Advance !!Regards,Mitul Parmar

Hello;I can't program and debug with the STM32H747 Discovery kit. I tried Stm32cubeProgrammer and STM32CubeIDE for this. Below are the errors I have received in both.Debug configuration screen is below;STLink Serial number appears, but I can't understand why it can't program it?Sincelery

I am evaluating different dual-core ARM Cortex-A7 MPUs for their graphical features; one of my requirements is that I need to support a 1280x1024 TFT LCD at 50-60fps using 16 or 24-bit parallel RGB interface.The evaluation kits offer small LCDs below my requirements, and I need to make sure that the MPUs can support what I need.Looking at the datasheet for STM32MP157C MPUs, it is clearly stated in multiple places that the upper pixel resolution limit for the LTDC module is WXGA (1366x768) at 60fps. However:the max pixel clock - LCD_CLK is stated to be 90MHz at specified supply voltage range. At that clock frequency, barring any external memory-related bottlenecks and assuming some small HSYNC/VSYNC + porch timings, I should be able to run a 1280x1024 LCD at around 63 fps max - and for sure at 60fps. Involved memory transfer clocks seem to be fine as well (I could be wrong on this one).LTDC register definitions seem to support much larger width and height values than what I need, so I s

I came a step further setting up the System Workbench for STM32.But now I am asked for a password to access to the target system but I all passwords that I can remember I had set-up before don't match.Can somebody show me, how I can reset the password required for the situation shown below.

I am planning to interface a STM32H753XI to a 1400x480 display. Here is the reference manual. Now, the maximum resolution given for the STM is 1024x728. I understand that this is the maximum frequency the device can actually output.Now my desired horizontal resolution exceeds the controllers 1024 pixels. I checked with the registers and they support 11 bit values (so everything up to 2047). Has anyone tried to interface a display with a larger horizontal resolution to an STM? Are the horizontal and vertical pixels a hard limit or is the combined pixel clock frequency the actual limit?

Hello;With STM32H747, I am trying to communicate with both cores. For example;To be able to read a variable in CM4 in the CM7 core. Depending on the state of this variable I read, running certain functions in CM7, etc.I couldn't find a document or example of how to do it.Sincelery

The maximum allowed internal clock for the device STM32F446RE is 180 MHz. The nucleo board has an external crystal of 8 MHz. Using this and a code I obtained from a university website, I attempted to change the system clock to 180 MHz using the PLL.(I use MikroC PRO for ARM v4.7.1)Here is the code.void InitializeClock() {RCC_CFGR = 0x00000000; //Reset Clock Configuration Register RCC_CR &= 0xFEF6FFFF; //Reset HSEON, CSSON and PLLON Bits RCC_CR |= (1 << 16); //Turn on HSE clock while((RCC_CR & (1 << 17)) == 0) { GPIOA_BASE.B5 = ~GPIOA_BASE.B5; // Toggle PIN A5 which is the LED(LD2) so as to know if the execution is still in the loop Delay_ms(500); } //Wait until High Speed External(HSE) Oscillator(8 MHz) is ready RCC_CR |= (1 << 19); RCC_PLLCFGR = 0x27405A08; //Set PLLP = 0, PLLN = 360, PLLM = 8, //PLLQ = 7, PLL Src = HSE RCC_CR |= (1 << 24); //Enable PLL on while((RCC_CR & (1 << 25)) == 0) { GPIOA_BASE.B5 = ~GPIOA_BASE.B5; // Tog

Posted on August 03, 2017 at 20:26Hi, recently in a project I need the GPIOs on STM32 to operate on 1.8v logic level. By quickly looking through datasheets, it seems many of STM32 can do so, for example, to STM32F407VG, if provide 1.8v to VDD, it runs GPIO on 1.8v level. However, I have difficulty to make such changes on TM32F4Discovery board, as there is no 1.8v power source available on the board.Now I have the question, which ST Discovery board or Nucleo board can support &sharp1.8v GPIO easily? I want to try it out. I need the board support USB port as USB device, and run the GPIO on 1.8v, it would be better if it provides I2C slave interface on 1.8v also.Thanks for your advice.-Andy#1.8v-gpio

#include "stm32f4xx.h" // Device header   void USART2_Init(void); void USART2_Write(int ch); void delayMS(int delay);   int main(void){ USART2_Init(); while(1){ USART2_Write('H'); USART2_Write('i'); delayMS(1000); } }   void USART2_Init(void){ RCC->APB1ENR |= 0x00020000; RCC->AHB1ENR |= 0x00000001; GPIOA->AFR[1] = 0x00000070; GPIOA->MODER |= 0x00000020; USART2->BRR = 0x342; USART2->CR1 |= 0x00000008; USART2->CR1 |= 0x00002000; }   void USART2_Write(int ch){ while(!(USART2->SR & 0x0080)){ USART2->DR = (ch & 0xFF); } }   void delayMS(int delay){ int i; for(; delay>0; delay--){ for(i = 0; i < 1000; i++); } }I am trying to Initialize and send data through PA3 (USART2_TX). When i connect the pin to a Serial to USB module to see the data sent on the terminal (CoolTerm) I get an error and doesnt' work. I set the baud rate based on that I have an 8MHz crystal on the board and still nothing is

​Hi, I encounter a problem to continuously display a physiological waveform through the subclass of CanvasWidget class developed. The dots on the line were added to an FIFO buffer in the subclass within the handleTickEvent() function of the view, then invalidate the corresponding rectangular area with InvalidateRec() function, the drawCanvasWidget() virtual function was reimplementation in the subclass to draw the lines with canvas render class.But as show in the picture, the lines near to the right border of the widget would flicking continuously. Is there a good way to solve the flicking problem ? Suggestion is needed here.

If we emulate the MCU watchdog reset on STM32MP1 it works fine. MCU is got restarted and runs after that. SYSRESETREQ assertion (by calling NVIC_SystemReset) works fine with dedicated M4 processor.We wander what can be a problem on STM32MP1 ?

I'm trying to downgrade a board to V2J27M15 and I read that you can do that using older version of ST-Link Utility, but I can't find where to download ST-Link Utility 2.3.30. Does anybody know? Thanks.

Using the :STM32MP157C-DK2 STM32CubeIDE