Solved

Hi, I'm testing the priorities of the modules, and I would like to know in which file the "Device Configuration Tool Code Generator" saved the NVIC definitions.I have a lot of code outside the delimiters, I can't use the "Device Configuration Tool Code Generator", so I need to know which file is saved, and change manually.

"Board A" is a previous revision that used STM32F103C8T6 to communicate with a device over CAN. It works great."Board B" is a new revision of the same board, but I migrated to STM32L431RCT6 because I needed more IO and it was readily available. Long story short, I can't get the MCU to do anything on its CAN interface. I thought maybe I missed something when porting the code over, but I tried creating a new CubeIDE project that just sends and receives, but I get nothing.The CAN transceiver itself is working fine. With another host transmitting on the bus I can see a nice clean signal on the RX pin (PB8) with 3.0V peaks. However, nothing shows up in the RX FIFO.Likewise, when the MCU is asked to transmit, nothing shows up on the TX pin (PB9).The CAN peripheral is configured like so. I'm running the bus at 250kb/s and the MCU is clocked at 80MHz.  void MX_CAN1_Init(void) { hcan1.Instance = CAN1; hcan1.Init.Prescaler = 20; hcan1.Init.Mode = CAN_MODE_NORMAL; hcan1.Init.Sy

..

We see this now more often than before (and there was an increase of this trend due to spam in the last few months even in Salesforce). I'd suggest the following steps:- consider first-poster moderation to cut back on the spam; yes, I know that means to spend on human work- remove the autosuggestions when trying to post, which are temptation to unexperienced users to use them as anchor for their first post. They are entirely useless as the AI behind them principially can't convey reasonable results in a technical forum (though it might be good enough for the usual Khoros customers selling cosmetics and alike)- lock threads older than say two years, this has been done in past and it was workable (assuming Moderators can unlock/modify locked threads upon request).JW

STM32F407 Discovery  typedef struct __UART_HandleTypeDef { USART_TypeDef *Instance; UART_InitTypeDef Init; const uint8_t *pTxBuffPtr; uint16_t TxXferSize; __IO uint16_t TxXferCount; uint8_t *pRxBuffPtr; uint16_t RxXferSize; __IO uint16_t RxXferCount; __IO HAL_UART_RxTypeTypeDef ReceptionType; DMA_HandleTypeDef *hdmatx; DMA_HandleTypeDef *hdmarx; HAL_LockTypeDef Lock; __IO HAL_UART_StateTypeDef gState; __IO HAL_UART_StateTypeDef RxState; __IO uint32_t ErrorCode; } UART_HandleTypeDef; I take the USART3 setting as an example.The starting address for storing this UART_HandleTypeDef structure will be 0x4000 4800.USART3 has 7 registers. Each register is 32 bits.7*32==224/8==28 bytes7 USART3 registers occupy 28 bytes.These 7 registers are configured by the USART_TypeDef *Instance structure;0x4000 4800 + 28 bytes== 4000 481C0x4000 4800 ----- 4000 481C There are 7 registers in this address limit.But USART3 is allocated a lot more addresses 0x4000 4800 - 0x4000 4BFF What's in ther

Hello Sir/Madam,I am working on STM32H735RGV6 for interleaved mode single dma. I am having problems while getting samples from the DMA controller with ADC. The problem is as the following.1. If I want to get 8192 or a smaller number of samples, there is no problem. I am getting the whole sample.2. If I want to get 8193 or greater samples, then a DMA transfer error occurs.The following pictures show my setup for ADC1 and ADC2.ADC 1 settingsADC 2 settingsADC 1 DMA settings#define ADC_DMA_BUFFER_SIZE (16384)volatile __attribute__((section(".dma_buffer_ram2"))) uint16_t ui16pAdcBuffer[ADC_DMA_BUFFER_SIZE];ui16pAdcBuffer --> It is in RAM_D2ADC DMA calling function setup 1: the following setup works well many times without any problem and I am getting HAL_ADC_ConvCpltCallback each time I want samples from ADCui32AdcDataSize = 8192if(HAL_ADCEx_MultiModeStart_DMA(&hadc1, (uint32_t*)ui16pAdcBuffer, ui32AdcDataSize) != HAL_OK){Error_Handler();}ADC DMA calling function setup 2: t

Hello!I would like to use the STM32 PMSM FOC firmware library. According to the release note of the SDK (https://www.st.com/content/ccc/resource/technical/document/release_note/b1/3f/4e/1b/cc/7f/45/c1/DM00068242.pdf/files/DM00068242.pdf/jcr:content/translations/en.DM00068242.pdf) the following microcontrollers are supported: STM32F030C6/C8/K6/R8 STM32F051C6/C8/K6/K8/R6/R8 STM32F072x STM32F100, STM32F103 STM32F2 Series STM32F302xB/C, STM32F303xB/C, STM32F302x6/x8 STM32F405xx, STM32F407xx, STM32F415xx, STM32F417xx, STM32F446xC, STM32F446xE. STM32F301C6/C8/K6/K8/R6/R8 How am I able to access the STM FOC FW library if I have designed a custom motor controller with one of the MCUs that I listed above? I have seen this question asked in previous posts and users are always directed to https://www.st.com/en/embedded-software/stsw-stm32100.html which forces you to use the MotorControl Workbench, but this can only be used with STM development kits and not a custom PCB

Hi all,I'm working with LSM6DSOX and I managed to get the accelerometer and gyroscope data from the output registers, but the numbers don't seem to be meaningful, how do I convert the raw data to g?

The installer for the latest CubeMX is broken on Linux, as the resulting directory structure lacks permissions in the jre/ subdirectory:cassiopeia:/opt/cubemx# ll total 150384 drwxr-xr-x 8 root root 4096 Jun 23 16:00 db/ drwxr-xr-x 2 root root 4096 Jun 23 16:00 help/ drwxr-x--- 7 root root 4096 Dec 12 2022 jre/ drwxr-xr-x 2 root root 4096 Jun 23 16:00 olddb/ drwxr-xr-x 3 root root 4096 Jun 23 16:00 plugins/ -rwxr-xr-x 1 root root 153956002 Apr 19 15:31 STM32CubeMX* drwxr-xr-x 3 root root 4096 Jun 23 16:00 third_parties_plugins/ drwxr-xr-x 2 root root 4096 Jun 23 16:00 Uninstaller/ drwxr-xr-x 4 root root 4096 Jun 23 16:00 utilities/Unfortunately, it's not just the top directory, but lots and lots of files and directories further down as well.  And no,chmod -R a+rx jreis not an acceptable solution.Also, the installer is unable to display the license agreement:──────────────────────────────────────────────────────────────────────────────── STM32CubeMX License agreement ──────────────

Hi there, I am working on a custom board based on OSD32MP157F. The pinout is very similar to the stm32mp157f-dk2 with the main difference that the Murata LBEE5kL1BX-883 is connected to sdmmc3 instead of sdmmc2 and that there is no ethernet peripheral on the board. I used the stm32mp157f-dk2.dts as a starting point and modified the pinctl to match the pinout of the board. The image is made with buildroot. I configured the sdmmc3 according to this and this guides. Although all tested peripherals work as intended, including an eMMC connected to sdmmc2 the wifi module is not responsive and returns a firmware load error on the bootlog 1.933870] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43430-sdio for chip BCM43430/1 [ 1.942625] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac43430-sdio.st,stm32mp157f-dk2.bin fa2 [ 1.942926] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 1.953593] brcmfmac mmc0:0001:1: Direct firmware load for brcm/brcmfmac4

Hello, I am using ST’s LSM6DSOW sensor for the Step Counting of my project that’s a Wristband. The device is worn on the user's wrist. The settings that I am using for the Pedometer are as follows:Enabling the Pedometer Algorithm: PEDO_EN = 1 Enabling the Pedometer false-positive rejection block and advanced feature block: PEDO_ADV_EN = 1Initializing the Pedometer Step Counter: STEP_DET_INIT = 1Enabling the False-positive rejection feature: FP_REJECTION_EN = 1 Configuring the Pedometer Debounce, the accepted values are 0 to 255. During the testing of different Pedometer Debounce values it has been observed that:Compared to other devices (such as Apple, Garmin, etc.), the step count shows a deviation of approximately 20%. The tests were conducted with our Wristband worn on the same hand as the other devices.Our device does not count a small number of steps (e.g. 5-10) but only registers larger movements. Is this behavior related to the Debounce setting?How

I wonder if the STM32_USB_Device_Library middleware is compatible with STM32U5?I can see that the USBX has been included in the Cube as the host/device library for U5 but since we want to migrate from STM32L5 to STM32U5 and we have already our usb communication based on STM32_USB_Device_Library, that might be great to see if STM32_USB_Device_Library could be ported or used on STM32U5? Otherwise we have to refactor our usb communication to use USBX libraryThank you in advance

Hii,I am using STM32h745IIK6. I want to use my SPI clock as a timer to generate delay in microsecond how can i to that. Please help with tutorial or your guidance.  Thanks in advance.

I'm testing and debugging a server application running on a custom board based on LAN8742 and stm32f207zg devices. Server has an UDP version and a TCP one. Firmware is built using LwIP stack (2.0.3 version), Raw api, non RTOS and HAL drivers (1.9.4 version.). As you know CubeMx generate a project folder structure and generates an ethernetif.c file used for "linking" MAC hardware to LwIP stack services. It also ad lwip settings, frame ethernet settings, PHY mask registers and PHY registers addresses definitions, etc..Clients are python implemented running on windows 11.Sometimes when server is running link is detected as down. So we were debugging and checking MAC registers where PHY is putting their register values using the mdio interface (for status and control communications). Observations:1.- Autonegotiation result and MAC configuration:When link up is detected and autonegotiation occurres it seems that PHY is detecting that mode is half-duplex, despite ethernet

Hi there,I am currently trying to get TouchGFX working on the U575I-Eval Board.Is there a project to start from?I made a new project with components initialised and TouchGFX activated.What do I need to activate too?Do I need the hx8347i driver? (from bsp or demo project of the eval board).If I correctly analysed the nucleo144 project, the lcd driver isnt even used?When i use X-Cube-Display->Board Part->Memory->Custom: OSPI, the "parameter settings" for external memory parameters tell me that bus type is "octo SPI", but the Instance says "Unavailable Quad SPI Mode", OCTOSPI1 is configured as Octo SPI. I dont get how i set it to OSPI and then it asks for a Quad SPI.Do I even need the X-Cube-Display? I found the "TouchGFX Presentation AL Development – Hands-on" where the X-Cube-Display isnt even used, but a LTDC instead of  FMC display is used there. Thanks in advance.

I am unable to start STM32 CubeIDE. As soon as I start it comes to the loading screen and is stuck there indefinitely. Can someone please help.

Apparently, some user profiles got lost, too. JW

I'm using X-NULCEO-NFC08A1 with NUCLEO-L476RG and sw sdk X-CUBE-NFC6 (project X-CUBE-NFC6\Projects\NUCLEO-L476RG\Applications\NFC08A1_PollingTagDetect).I'm using an IPHONEX (ios16.5) with a custom app that writes nfc tag (but I've also tried the freeware version of app NFCTool available on the store).The ST25R3916B should act as CARD EMULATOR and READER (both modes...but I've problems in CARD EMUL. mode)Everything well, till when the data size written is lower than 90-100bytes...BUT when I try to write (from IPHONE to X-NUCLEO) a tag with bigger data size (for example 150bytes), it happens that last bytes (for example the bytes from 130 to 150) are written over the first bytes of the buffer.I've spent many days to reselve this issue without succes.  any hints ?  may I have the sw project NFC08A1_PollingTagDetect already configured to perform this task ?thanks

I'm missing the "10 years of STM32" thread, https://community.st.com/s/feed/0D50X00009bLUFDSA4 , mainly for its infographics showing the progression of individual STM32 families (https://community.st.com/sfc/servlet.shepherd/version/renditionDownload?rendition=ORIGINAL_Png&versionId=0680X000006qOEu&operationContext=CHATTER&contentId=05T0X00000NPLil .   JW

I cannot find a way to get this to work... Already using run as administrator.

Hi,I have managed to program the STM32F746G-DISCO with a simple neural network but when I try to do it using the external Flash by using the option in advanced settings (External NOR Flash) it doesn't work. Any idea why? Is there anything else I need to do?I'm using STM32CubeMX and Keil.Thanks!

I'm attempting to bring up a project on a Nucleo-H755 board using only the CM4 core (the CM7's boot is disabled). I have proved out that the ADC works as expected with polling and interrupts, but I can't get DMAs to function.I found and reviewed the H7 DMA issues knowledgebase issue, but I don't believe this is relevant as I am not using the CM7 core and I have confirmed that the DMA target buffer is in D2 SRAM. I have ensured that `MX_DMA_Init` is called before `MX_ADC_Init` as suggested elsewhere, and I have reviewed myriad examples for other STM32 parts, all of which match what I'm trying to do, with no success.I've removed the M7/M4 interlock, as I'm only booting the M4, and I have moved the `SystemClock_Config` function from the CM7 main.c to the CM4. I've attached both my main.c and .ioc file here, but the general flow of the program is: uint32_t result = 0xFFFFFFFF; uint32_t adc_buf[2]; void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef *hadc) { result -= 1; } int

I'm using the STM32C031C6 configured with USART1 in 115200. When opening communication with the YAT serial terminal, the bytes are sent and received wrong. (I used STMCubeMX for code generation).Ex: (YAT configured correctly as it works on an older project)sending from YAT to uC 55h I get b5hsending from uC to YAT 55h I get varied values (95h, D5h, B5h together with message XXh [Warning: RX FRAMING ERROR]). When I setup RX and TX in loop, on YAT I always get D5h. uC always puts 0x80 in the 4 most significant bits of the received byte 55h + 80h = D5h (happens for other data) or TX sends data before RX is ready or something like that...Tests:BaudRate from 115200 to 9600 on both sides (uC and YAT);WordLength 8 and 9 bits;StopBits 1 and 2 on both sides (uC and YAT);Parity None and Odd;ClockPrescaler for multiple values; andI use internal oscillator, so I used PCLK from 3MHz to 12MHz and the error persists.As commented above, with RX and TX in loop on the board, the transmitted and rec

Hello,we consider using SPC57x or SPC58x for our products. I did find Safety Manuals for STM8 and STM32 but non for SPC5x. I know the chapter in the Reference Manuals with explanations of the CRC, STCU2 ... modules but I'm missing a complete list/table of neccessary safety mechanisms like in the STM32 Safety Manuals.Were can I get the Safety Manuals for the SPC57x and SPC58x?Fabian S.

Does anyone know how to enable a timer interrupt in SCP582b?