Solved

Can the antenna of this board be led out for measurement? How do I lead out the line for measurement? If not do I need to rebuild the board?

Hello.  I try to develop a FW which should include USBPD SOURCE and USB HID device. My current dev kit -is SRC1M1 + MB1360-G0B1RE. The USB PD functionality was added in accordance with Stm32 wiki link for PD Source device - it is tested and OK. After that USB HID device was added with Cube configuration: enable USB_DRD_FS as a device_fs; check Interrupts enabling; enable USB support into USBPD middleware; configure USB_DEVICE middleware;    After that project was compiled and flashed. A Type-C cable is connected to the laptop with Windows 10 and HID device was not detected.   Next try was to connect MB1360-G0B1RE to MB1303B (only USB2.0 data lines, 3.3V and GND), because P-NUCLEO-USB002 kit has never had this issue with USB and Cube code .    This setup is working for USB2.0 - HID device is detected over Type-C. I checked a schematics for both boards(MB1303B and SRC1M1) - it looks like that USB2.0 lines are independent from any other lin

Using SPC572 GTM for ecu, what is the best way to stop ATOM output in critical fault?Already tried to stop the GTM, but on re initialize the result is unpredictable. 

I’m trying to find a replacement for this device from a light dimmer. I think it’s a triac, but the numbers on the front don’t match any search results, other than a similar request on this forum, so I’m hoping that someone can help!  

Hello,  I try to write the sensor_fusion.code in ESP32. I get below compilation error;Compilation error: 'LSM6DSV16X_SFLP_GYROSCOPE_BIAS_TAG' was not declared in this scope here is my code;#include <Arduino.h>#include "lsm6dsv16x_reg.h"#include "lsm6dsv16x_fsm_sflp_asc.h"// #include "lsm6dsv16x_reg.c"#include <Wire.h>/** I2C Device Address 8 bit format  if SA0=0 -> D5 if SA0=1 -> D7 **/#define LSM6DSV16X_I2C_ADD_L 213#define LSM6DSV16X_I2C_ADD_H 215/* Private macro -------------------------------------------------------------*//* * Select FIFO samples watermark, max value is 512 * in FIFO are stored acc, gyro and timestamp samples */#define BOOT_TIME         10#define FIFO_WATERMARK    32/* Private variables ---------------------------------------------------------*/static uint8_t whoamI;/* Private variables ---------------------------------------------------------*/static lsm6dsv16x_fifo_sflp_raw_t fifo

hi, I'm using a discovery stm32f429 together with the STM32CubeIDEI would like to know why when I use while to wait for the mailbox:while (HAL_CAN_GetTxMailboxesFreeLevel(&hcan1) != 3){// Wait until all transmission buffers are free}the debug does not work and gives an error:Failed to assign value 8000c69, to register 0Failed to assign value 20000028, to register 0Failed to assign value 2002fff8, to register 0Failed to assign value 80011d4, to register 0If I use the command HAL_CAN_GetTxMailboxesFreeLevel it works normally or if I use RUN it works normally on the board, but I would like it to work in debug to see some information through the STM32CubeIDE

Hi,We are starting a LoRaWAN project here at the company and we are going to use the LSM110A module that has the STM32WLE5CC.I would like to know if you have a LoRaWAN stack for this ARM processor (STM32WLE5CC), or a video demonstrating how to start the project with the STM32Cube IDE?Thank you!Regards,Tiago Fernandes

Dear Sir,     I am trying to read the distance from the VL53Lox i can read upto 400mm , when i try to measure more the 400mm it is not reading proper reading. Please guide 

Hello all.Another question regarding SBSFU, this time 1 image version.When we download new image via YMODEM, when does decryption process happen?1. Is new image first downloaded into active image slot and then decrypted?2. Is new image downloaded and decrypted at the same time, which is basically decryption on the fly, but that requires special hardware accelerator? Thanks in advance!

Hello, I hope you are well.I had a query about the IMU ASM330LHH. I want to know whether the self-test functions of the internal accelerometer and gyroscope (see attached pictures) test the internal MEMS sensors or not. I have doubts whether these self-tests only internally generate standard values for acceleration and angular velocity without actually testing the MEMS.Thank you very much.

Hi,I'm running the latest release 6.9.2 of STM32CubeMx with admin rights. When I'm going into the install/remove packages and scroll down to the X-CUBE-TOUCHGFX package, the latest release 4.22.1 does not appear, even after a press on "Refresh" button.I exited STM32CubeMx, retried: same result. The latest package version does not appear. In the end I downloaded the latest package from ST's website.I guess this is abnormal, no?Any hint?

Hi there!​I was wondering, for a school project, if it is possible to disable te autocalibration on the VL53L5CX and if it would be possible to manually calibrate it?​Thanks! :fox_face:

Hello, does Android phone can serve as the NFC reader and support Fast Transfer Mode(FTM) in this diagram? If yes, what is the speed?Is FTM unique to ST NFC tag products?Thanks!

Hi, I just got the nucleo stm32G474RE board and I'm trying to run a simple code with the STM32CubeIDE through Linux ubuntu 22.04 the problem is that my laptop seems to not recognize the board when I am connecting it via USB port literally nothing happens. There is no new window that appear in my computer telling me that a new usb device is connected I know I have the ST-Link drivers already installed since when I'm trying with my nucleo stm32F446RE board everything works fine. I would appreciate if you could helpThank you

The problem you are experiencing with your STM32F407IGT6 board is that after programming the firmware and using Ethernet (UDP) communication, if you power it off and then back on, the Ethernet communication doesn't work. However, if you press the Reset button, Ethernet communication becomes operational again. Do you happen to know the reason for this?

HiEarlier today I was demonstrating a IAP functionallity with dualbanking on a stm32G474RET. I was saying that it cannot fail as I check the written image with a CRC after it has been written to the new bank.As I power of the system mid transfer and power it up again, I experience the what we now all expect. It obviously failed.My system no longer boots normally and as i start to debug it i see that i get a NMI. Now, I unfortunately did not record all the relevant register values, but i am pretty sure that what was set was FLASH_ECCR, bit ECCD. I know this because i see that the NMI trigger as i am doing a boot blank check and CRC on both my banks and the NMI triggers while i am reading from the bank i was writing to.I have now written a suitable NMI handler to deal with this situation in the future, but how can I intentionally force a double ECC error in a given address in flash?Best regardsMartin  

What is that? Ref.: https://community.fabric.microsoft.com/t5/Community-Feedback/Post-flooding-detected-community-received-posts-of-a-unique/td-p/1578923

Nucelo-F103RB has MCU STM32F103RBT6.  Can this MCU be used as USB host ? I see STMF105 series has USB 2.0 OTG but I don not see Nucleo-F105 series Evaluation board.  

At present, there is no mature NFC WLC function, so can I complete the wireless charging function through ST25 and STWBC86? ST25 completes the transmission of information, and the electric energy obtained by STWBC86 based on Qi supplies power to MCU?As shown on page 5 of https://www.st.com/resource/en/product_presentation/ST25_NFC_presentation_for_Wireless_Qi_charging_protection_applications.pdf , complete the battery charging of the ST25.

I want to setup an system with 4.3" 480x272 LCD Working with LTDC with external flash (External Flash Loader)Can we directly interface an existing QSPI Loader if yes, Then Which one.

I should make an application with NFC where the entire circuit is powered by energy harvesting.For this reason I thought of using the ST25DV and I have already purchased the X-NUCLEO-NFC07A1 and X-NUCLEO-STM32L476RG.I have successfully obtained the energy harvesting of the antenna and can light the LED, now I want to use the energy of the antenna to wake up the MCU (L476), what do I need to do?I have tried to connect VCC with EH pin, but L4 is not waking up, what should I do to power the antenna to the MCU (L476) instead of the ST-LINK USB

I understand that in order to prevent wireless charging from affecting the ST25 tag, capacitive elements are added inside it. But are there any examples of wireless charging through ST25 combined with Qi?

i am finding issue like my application is not working in stm32cubeide 1.13.2 but it works in 1.8.0.Please help in solving this .  

Hi,I use the BFA001V2 board as a counterpart for testing IO-Link Master with BLOB transfer. A problem was detected while reading a BLOB.When using BFA001V2, after 15 successful data transfers (flow_control set to 0x2F), an invalid flow_control with a value of 0x30 (last frame) is sent. (However, the total size of the blob must be 16 KB!).According to the IO-Link specification, flow_control should cycle from 0x20 to 0x2F, after almost all bytes have been sent, the Last_block command (0x30) should be sent with the last block of data. Could someone check the stack on BFA001V2?Thanks in Advance D.Krush

Hi, i am using STM32F401RE Nucleo board and i want am using I2C channel in standard mode which is upto 100KHz but i due to little long length of communication cable, i want my I2C frequency to be around 20KHz. I am using HSI only as clock source.This is my function to use I2C channel.void i2c_init(){// I2C3 RCC CLK enableI2C3_CLK_EN;// Freq setting 16MHzI2C3->CR2 |= (16 << 0);//CCR configurationI2C3->CCR = 0x50;// T-Rise configurationI2C3->TRISE = 0x17;// Set OAR bitI2C3->OAR1 |= (1 << 14);// Peripheral EnableI2C3->CR1 |= (1 << 0);}