Solved

Hi Please can you advise on the Thermal Resistance (K/W) of LSM6DSOXTR please so we can complete our ATEx evaluation. Many Thanks Dominic

The problem is pin PB4, which is always powered.It is the same as returning to "STM32CubeG4_Demo_NUCLEO-G474RE.hex".Do I need to send it in for repair??How to send??  

Hello,LIS2DH12 accelerometer. AN5005 datasheet. How is the data in the table in column 1 (Acceleration values) calculated? (See Figure 1). I read the calculation process in the datasheet above, but did not understand it. (See Figure 2).

Hello ST community, I am leading a project at university and I would like to make a communication between two STM32WL55JC1 cards using the LoRa protocol without a gateway. I'm not very familiar with STM32CubeIDE and any help would be much appreciated.The aim is to recover data from an accelerometer that will be transmitted by a serial communication to the first STM32 card and then make a wireless communication to recover the data on the other card. First of all, I would like to know if I can make a communication between two LoRa device without using a gateway. Thanks for your answers. Jules.

Hello all, We will probably need to go for custom cover panels for our sensors, however, we could not find a clear list of requirements to follow.Material: The product's datasheet (DS13812 - Rev 6) states that "the VL53L4CD achieves the best ranging performance in various ambient lighting conditions and for a wide range of cover glass materials." We were considering PMMA or PEI + PC as Gilisymo's / Hornix's cover panels for the VL53L4CD use these materials. Are there other materials worth considering?Thickness and air gap: We came across AN5231 - Rev 1 that provides cover window guidelines for the VL53L1X sensor (not the VL53L4CD).  In Section 5.2.6 ST states that "for sub 1000 mm ranging– Total air gap and cover window thickness = 2 mm maximum– Cover window thickness <1.5 mm and air gap <0.5 mm"Is this also valid for the VL53L4CD, or are the recommended air gap and cover window thickness values different? Please let me know if there is document

Hi, I have configured an LED for RF field status in the rfal_plafrom.h.The LED switches on when rfalNfcDiscover() is called. But the LED does not switch off when the rfalNfcDeactivate(RFAL_NFC_DEACTIVATE_IDLE); function is called. This function returns RFAL_ERR_NONE and I am expecting the LED to switch off. How can I confirm if the RF field is off ? Why does not the LED turn off ?RFAL library used is 2.8.0    

How can I measure the sleep current of the chip on the STM32F103C8 board? 

HelloI am trying to powerup external 8MHZ crystal on STM32F407VET6 MCU but it is completely dead. I run the LED bliking program using HSI, and it is working sucussfully. Boot 0 and Boot1 pins have been PD with 500 ohm.  I also run the same code to use HSE on STM4 Discovery board after removing R68, I see HSE on board is working. Below are my caclulationFrequency = 8 Mhz,Co = 7 pF ( as per datasheet)CL= 10 pF ( as per datasheet, used 20pF CL1 and CL2) ESR = 100  ohm ( as per data sheet)After calculation gmcrit comes..gmcrit = .287 gm =  5 ( from ST data sheet)gain margin = 5/.287 = 17    so gain margin > 5 condition is met. I also changed Rext  to 0, 100, 200, 500 , 1000 ohm. HSE is dead. PCB design seems ok , and I assume for now no issue with PCB design.I have gone through AN2867, but not sure what point I am missing.Kindly suggest where could be the fault.  I eliminate software issue as same code is ma

Good morning,I am building a system with stm32 wl55jc1 to count water flow with a pulse flow meter.So I created two internal clocks in stm32 one to create a time window and the other that counts each pulse received from the sensor. At the trigger of the first clock I check how many pulses the second clock counted and get the instantaneous flow rate.I put an LED in parallel with the signal to visually see the pulses. The problem is that the count the clock makes and the pulses I see do not match.I would like to ask for some documentation on the input voltage and so that I can design my RC circuit as best I can (as I am convinced that the problem is electrical). thanks for your time, greetings Roberto  

Please I need someone to review the code I wrote I double checked few times but am probably missing some info and configuration. I want to display red color on display module by only setting bits in the register. Here is the provided code. Someone please help I am working on a homework project. #include <stdint.h> #include "stm32h7b3xxq.h" #include "reg_util.h" #include "main.h" void SystemClockSetup(void); void VcoreSetup(void); void LTDC_Peripheral_Init(void); void LTDC_Peripheral_Setup(void); int main(void) { HAL_Init(); SystemClockSetup(); VcoreSetup(); LTDC_Peripheral_Init(); LTDC_Peripheral_Setup(); /*Loop forever */ for (;;); } void VcoreSetup(void) { //Povecaj wait states i latency FLASH->ACR |= (3 << 4); FLASH->ACR |= 0b0111; //Disable SMP //PWR -> CR3 &= ~(PWR_CR3_SMPSEN); //Disable Bypass //PWR -> CR3 &= ~(PWR_CR3_BYPASS); //Wait for ACTVOSRDY bit //while(!REG_READ_BIT(PWR -> CSR1,PWR_CSR1_ACTVOSRDY_Pos));

I am booting from EMMC with this flash layout./dev/mmcblk1p1 : start= 34, size= 1024, type=8DA63339-0007-60C0-C436-083AC8230908, uuid=077BFE04-5B1A-41F8-8DC2-B47FCC4EA832, name="metadata1"/dev/mmcblk0p2 : start= 1058, size= 1024, type=8DA63339-0007-60C0-C436-083AC8230908, uuid=9487F545-20A2-495E-A515-41B16AF75FE7, name="metadata2"/dev/mmcblk1p3 : start= 2082, size= 4096, type=19D5DF83-11B0-457B-BE2C-7559C13142A5, uuid=4fd84c93-54ef-463f-a7ef-ae25ff887087, name="fip-a"/dev/mmcblk1p4 : start= 6178, size= 4096, type=19D5DF83-11B0-457B-BE2C-7559C13142A5, uuid=09C54952-D5BF-45AF-ACEE-335303766FB3, name="fip-b"/dev/mmcblk1p5 : start= 10274, size= 1024, type=3DE21764-95DB-54BD-A5C3-4ABE786F38A8, uuid=5BB4327D-D6F5-4007-BE5C-85681ED9C1E7, name="u-boot-env"/dev/mmcblk1p6 : start= 11298, size= 974848, type=0FC63DAF-8483-4772-8E79-3D69D8477DE4, uuid=929FE52B-B9E0-459A-80AB-A8F82878CB57, name="bootfs", attrs="LegacyBIOSBootable"/dev/mmcblk1p7 : start= 986146, size= 32768, type=0FC63DAF-8483-4772-8

Hi all,I've got a custom Assert Failure Handler ready to go, and I'm wondering if there's a good way to display assert information (file name/line number) after an assertion has happened in the MVP context? I'm thinking the only way to do this is to write directly to frame buffers? Is there HAL code available for the H7 (using custom hardware with an STM32H750 chip) to do something like this? Or is there a better solution available within TouchGFX?

Hi, we are using an ST25R3911B NFC reader. Is it possible to drive this chip without a crystal, and use a generated clock source instead (coming from an MCU)? We found the following article on your forum: https://community.st.com/t5/st25-nfc-rfid-tags-and-readers/is-it-possible-to-use-a-clock-oscillator-instead-of-quartz/td-p/301081, but for some reason we are not getting it to work. The input clock we use looks OK when using a oscilloscope. We configured the tana_7, as well as the OSC bit, but is seems not to give an analog field (but we are able to communicate to the reader over SPI).If this is possible, what is the moment that these registers need to be configured?  

"Hi, I'm working on an EV project. We're attempting to implement the CAN bus protocol on STM32. I'm wondering if there's a way to communicate between two STM32s using the CAN bus without using a module?"

Hello, 2 MEMS microphones share a common Clock (PB3, ADF1_CCK0) and Data (PB4, ADF1_SDI0) of a STM32U585QI.Using ADF the PDM signal is processed successfully. It processes either the data of the either falling or rising edge depending on setting Init.FilterBistream to MDF_BITSTREAM0_FALLING or MDF_BITSTREAM0_RISING.For the second microphone an MDF1_Filter0 instance is used. It is used with the same Init and Config data as the ADF instance.For ADF an MDF the calls to HAL_MDF_Init HAL_MDF_AcqStart are both successful.But then HAL_MDF_PollForAcq is only sucessful or ADF, but for the MDF instance it always returns HAL_TIMEOUT.Does the MDF need to be configured differently? How must the ADF and MDF be configured to use both MEMS microphones with shared data and clock?Does the MDF require other clock divisors?I checked the examples inhttps://github.com/STMicroelectronics/STM32CubeU5There is only 1 example using rising and falling edge. Both filter are MDF in thi

Hello,I need exact part number for smd diode GB4 or maybe G84, which I have attached the image.Thanks.

I have attached my project. I am running it on a NUCLEO-F429ZI Board. I am using FreeRtos and LWipI have 2 threads/Tasks. The first Task is to initialize LWIP and to read some ADC from DMAThe lcd Task is to display text on a 2" LCD through SPII have also added a server TCP/IP initialization through the first taskEverything seems to work until I start communicating with a TCP Client. After a few communication from the client to the server, all my tasks hangs. (See Logic Plot)And when I pause the debugger, it seems to be stuck in a semaphoreTake as shown on the screenshot of CUBEIde Anyone has an idea of what is going on ? Thank you

Hi, I am reading from IMP34DT05 (master receive, PDM), and I always receive 0x00 0x7F 0xFF 0xFF ...and 0xFF's, ever after, until reset of SAI (disable-enable). Playing sound into mic has no effect. In debugger, immediately upon SAI enabled, FIFO is full and underrun flag is on, before any data is read. Here is my current ioc config:And register values, just in case (WB55):Mic L/R is on GND. Mclk is 50MHz.I tried different configs with same result; frame synchro length, 8/16kHz, rising/falling edge.Where am I wrong?

Hi all,One small doubt on the tamper configuration, is it possible to configure both active and Passive tamper in the Same project/API, or  both should be in different project/API. why this doubt is as Seed is not required for Passive tamper, so does it effect the passive tamper implantation if we implement in the same project.

I'm encountering difficulties modifying option bytes on an STM32H723VEH6 microcontroller using a custom C# bootloader. Although the bootloader successfully loads firmware onto the microcontroller, it fails to modify option bytes BOOT_CM7_ADD0 and BOOT_CM7_ADD1 despite following the correct sequence outlined in the reference manual.If anyone has a code example demonstrating the correct implementation of modifying option bytes using a custom C# bootloader?public void ModifyOptionBytes(uint bootCm7Add0, uint bootCm7Add1){      UnlockFlashCR();      UnlockFlashOPTCR();      // Write the desired new option byte values in the corresponding option registers      WriteOptionBytes(bootCm7Add0, bootCm7Add1);     // Set the option byte start change OPTSTART bit to 1 in the FLASH_OPTCR register     SetOptionByteStartChange();}

Hi all,I created a dual core project for STM32H745 Disco board. I'm using the cubeIDE and I said "yes" to set all peripheral to their default values. I wonder which core (CM4 or/and CM7) is booting and which was not. The reference manual (RM0399) says that this depends on the settings of BCM4, BCM7, BOOT_C1 and BOOT_C2. But BCM4 and BCM7 show "X" as the reset value.Looking at the actual code in each main file it looks like both cores are booting. CM4 sets a semaphore and goes to sleep waiting for CM7 to configure the system clock (SystemClock_Config()) and release the semaphore to enable CM4 to continue to run.Is this correct? What are the reset values for BCM4 and BCM7? Can the system clock be configure in CM4 instead of CM7?Thanks.

Hi.Im using the ST X-NUCLEO-NFC08A1 expansion board and i want to read the HEX Memory of a NFC-V Tag like the ST-Tab App..Im using the NFC08A1_HelloWorld.ino (github.com/stm32duino/X-NUCLEO-NFC08A1) and it says:ISO15693/NFC-V card found. UID: E00225031E35CNDEF NOT DETECTED (ndefPollerNdefDetect returns 5)Operation completedThe NDEF format is not correct, i know. Thats why i need to modify the code to make a RAW Memory Data read.Does somebody know what functions i can use with the RFAL or what needs to be modified to archieve that?Your help would be greatly appreciated!

I'm trying to build the example project "Tx_Thread_Creation" for the NUCLEO-F429ZI. During the build process with the MDK-ARM (uVision) V5.28.0.0 toolchain I got the following linker errors:linking... Tx_Thread_Creation\Tx_Thread_Creation.axf: Error: L6218E: Undefined symbol __RAM_segment_used_end__ (referred from tx_initialize_low_level.o). Tx_Thread_Creation\Tx_Thread_Creation.axf: Error: L6218E: Undefined symbol _vectors (referred from tx_initialize_low_level.o). Tx_Thread_Creation\Tx_Thread_Creation.axf: Error: L6218E: Undefined symbol g_pfnVectors (referred from tx_initialize_low_level.o). Not enough information to list image symbols. Not enough information to list load addresses in the image map. Finished: 2 information, 0 warning and 3 error messages. "Tx_Thread_Creation\Tx_Thread_Creation.axf" - 3 Error(s), 0 Warning(s). Target not created. Build Time Elapsed: 00:00:03I also tried to build the same project with the STM32CubeIDE Ver. 1.8.0 toolchain. The build process finished s

Hello,I would like to know if Nucleo-H563ZI board could be used as a USB host, using the user USB (CN13). I'm asking because I'm a bit confused, honestly - I've only found examples where it's being used as a device and the board manual seems to mention only as device and sink only for the CN13 connector. OTOH, in CubeIDE, after starting a new project based on this board, the USB and USBX can be configured as host, without any restriction. And, if it's possible, should UCPD1 and USBPD be enabled along with USB and USBX, or it's enough to call HAL_PWREx_EnableVddUSB at the end of HAL_HCD_MspInit? Basically, what I want to implement is reading VID, PID and SN from a USB storage device plugged in CN13 and printing them over USART3.Thanks!

I am trying to implement application with password access and change option. Please suggest a way to store password/user data in flash memory. Are there any APIs or applicaiton note for more information?