Solved

I am following getting started guide of this board STM32MP157x-DK2 https://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP157x-DK2/Develop_on_Arm%C2%AE_Cortex%C2%AE-A7/Create_a_simple_hello-world_application When I am connecting an ethernet cable, after a while, this error message pops again and again..  "Activation of network connection failed" on Ubuntu machine. I can't see the IP address so I am stuck at this step. 4. Deploy and executescp gtk_hello_world root@<board ip address>:/usr/local

https://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP157x-DK2/Develop_on_Arm%C2%AE_Cortex%C2%AE-A7/Create_a_simple_hello-world_application#Deploy_and_execute I am at the last step.Application is building without error and I am successfully able to send it to the board. But when I am executing it on the board, it is giving me below error.  root@stm32mp1-e1-a2-8b:/usr/local# su -l weston -c "/usr/local/gtk_hello_world"/usr/local/gtk_hello_world: line 1: ELF: not found/usr/local/gtk_hello_world: line 2: �: not found/usr/local/gtk_hello_world: line 5: syntax error: unterminated quoted string Here is my make output:arm-ostl-linux-gnueabi-gcc -mthumb -mfpu=neon-vfpv4 -mfloat-abi=hard -mcpu=cortex-a7 -D_TIME_BITS=64 -D_FILE_OFFSET_BITS=64 --sysroot=/home/STM32MPU_workspace/STM32MPU-Ecosystem-v6.1.0/Developer-Package/SDK/sysroots/cortexa7t2hf-neon-vfpv4-ostl-linux-gnueabi -o gtk_hello_world gtk_hello_world.c -O2 -pipe -g -feliminate-unused-debug-typ

 STM32F103C8T6 CAN Not Responding — UART to CAN TestI’m testing a very simple setup with two STM32F103C8T6 (Bluepill) boards.The goal is just to send data from my PC to one STM32 through UART, and then transmit it over CAN to another STM32 board.SetupData flow:  PC (PySerial) → UART → STM32 (Transmitter) → CAN Bus → STM32 (Receiver) → UART → PC  Hardware used:Two STM32F103C8T6 boardsMCP2551 CAN transceivers120 Ω termination resistors at both endsCommon ground between boardsUART baud: 115200CAN bit rate: 1 Mbps (Prescaler = 2, BS1 = 15, BS2 = 2)What’s WorkingThe PC is successfully sending UART data using Python (PySerial).The STM32 transmitter receives the data correctly — UART works fine.The DMA callbacks trigger as expected, showing that data reception over UART is confirmed.What’s Not WorkingThe CAN bus is not showing any transmission or response.The transmitter’s CAN doesn’t seem to send anything, even though initialization completes without errors.The receiver b

The subject line says it all - any help will be appreciated 

The datasheet for STM32U585 and 575 list there are two SAI on the chip. In CubeMX I can only see SAI1 (A and B sub-blocks)Datasheet CubeMX pin menu    

Hi everyone, im using an STM32WB and i just managed to get my own BLE<->UART bridge to "half work".But my problem is about UART managing.If i receive data with length of less than 247bytes(set by me) just stays in the rx bufer and no DMA transfer complete happens.I set up the DMA to listen for the next incoming 247 bytesHAL_UARTEx_ReceiveToIdle_DMA(&huart1, NotifyCharData, RxBuf_SIZE); __HAL_DMA_DISABLE_IT(&hdma_usart1_rx,DMA_IT_HT);//we dont want the half done transaction interruptWhenever the data arrives(stream of data uartRx) ,it gets written into a BLE characteristic, everything works like a charm, but if the last uart received message is less than 247length DMA rx doesnt trigger after an idle time.No IDLE event occurs./** * @brief Receive an amount of data in DMA mode till either the expected number of data is received or an IDLE event occurs. * @note Reception is initiated by this function call. Further progress of reception is achieved thanks * to DMA services,

I’m currently testing my own quantized model on the STM32N6570-DK, using the official X-CUBE-AI application example.All Model Zoo examples (e.g. SSD, image classification) run perfectly with the same firmware and codebase.However, when I replace the model with my own quantized TensorFlow Lite model (Zero-DCE, converted with ST Edge AI Developer Cloud), the inference process freezes — even though the conversion and compilation complete without errors.I’m wondering if there is a hard restriction that prevents models from running when used RAM exceeds the on-chip SRAM (≈ 4.2 MB), even though the report shows that part of the activations are mapped to external HyperRAM.Here are the key parts of my Edge AI Core 2.2.0 generation report:ST Edge AI Core v2.2.0-20266Model name: zerodce_int8_192Total memory usage:----------------------------------------------Total: 11.643 MBWeights: 78.751 KBActivations: 11.566 MBMemory mapping:cpuRAM2 [0x34100000 - 0x34200000]: 1.000 MBnpuRAM3 [0x34200000 - 0x3

Hello ST Community team I would like to report a possible issue with the contributor ranking in the “Best Answers” leaderboard. For example, when applying the Last 24 hours filter, I noticed that two contributors appear ranked as #20 and #21 on the first page:   But on the second page, the same contributors are shown as #24 and #25: The screenshots were taken at 10:20 GMT. Could you please check and correct this inconsistency in the ranking display? Best Regards. II

Hello,In the STM32CubeC0 v1.4.0, when I enable the BYPSHAD bit in the CR register and later try to deinit the device, I get an ERROR. It does not happen if I disable it before deinitialising. Should I disable it by hand, or is it a mistake and should be cleared as in other families? HAL version is clearing the whole register to the reset value when deinitialising.Best regards,Tomáš

I am trying to drive a 5 inch 800x480 touch display from waveshare using my STM32MP257F-DK development board. My Linux distro is a custom one built using Buildroot via bootlin support.When running `modetest -M stm -c`, I don't get any resolutions printed. Here's what I get:# modetest -M stm -c opened device `STMicroelectronics SoC DRM` on driver `stm` (version 1.0.0 at 20170330) [ 244.014209] EDID block 0 is all zeroes Connectors: id encoder status name size (mm) modes encoders 32 0 connected HDMI-A-1 0x0 0 31 props: 1 EDID: flags: immutable blob blobs: value: 2 DPMS: flags: enum enums: On=0 Standby=1 Suspend=2 Off=3 value: 0 5 link-status: flags: enum enums: Good=0 Bad=1 value: 0 6 non-desktop: flags: immutable range values: 0 1 value: 0 4 TILE: flags: immutable blob blobs: value: 33 dithering: flags: enum enums: Off=0 On=1 value: 0Here's what dmesg logs (Increased logging level using: `echo 4 > /sys/module/drm/parameters/debug`):[ 2

Hopefully this is not a dumb question...I am referencing the example code here:https://github.com/STMicroelectronics/STM32CubeG4/tree/master/Projects/STM32G474E-EVAL/Applications/OpenBootloaderI see the entry point for the the open bootloader app (app_openbootloader.c), but I don't see where the actual core files for the the bootloader are ( ie openbl_core.c)Where would those files be in that project? Do I just download those files from here seperately? https://github.com/STMicroelectronics/stm32-mw-openbl/tree/main/Core  

Hi,We are building an IoT device, using STM32L476RET6 as main core. It communicates with an LPWAN modem with AT-commands via UART. We have redirected UART2 into external pins for "serial output" into Nucleo RX pins.During testing, we noticed initially that some devices where seemingly "stuck" in some state - no printing in Nucleo RX, not responding to external interrupts - while communicating with LPWAN modem ( it stayed in idle ON state). No hard fault or similar (we have put checks inside repsective callbacks). IWDG can reset the device, but it is a "last resort" method.After putting device in debug mode, catching the situation and pausing the code, it stopped here : void HAL_UART_IRQHandler(UART_HandleTypeDef *huart) { uint32_t isrflags = READ_REG(huart->Instance->ISR); uint32_t cr1its = READ_REG(huart->Instance->CR1); <<<-------Looking at USART1 ISR register, we found ORE error flag.Resuming the code in debug mode makes the MCU continue, but in run

Hello everyone, I am using an STM32 microcontroller and I am facing a problem when I try to mount an external flash memory. The problem is inside the function lfs_dir_fetch which is returning unexpected values in the test buffer here:  struct lfs_disk_dir test; int err = lfs_bd_read(lfs, tpair[i], 0, &test, sizeof(test)); lfs_dir_fromle32(&test); the returned values are:  Invalid size: test.size = 335610112, block_size = 40960 Invalid size: test.size = 335610112, block_size = 40960 lfs error:495: Corrupted dir pair at 0 1 lfs error:2214: Invalid superblock at 0 1 (*)Error in mounting external flash memory I have successfully communicate with the external flash, since I am able to read its manufacture ID. I have also configured properly the littlefs function and I test them by writing raw data to the external flash and I was able to receive them correctly. I cannot understand what is the test variable that is being declared and why

Hi ST Community,once again I have found a USB PD Specification violation, that I can't find the reason for:Source operation: According to USB PD Spec the order of action is as follows:1. Detect Sink using CC lines and only if sink is detected continue with the next points2. Enable VBus to safe5V3. Once safe5V is applied send source capabilities message However current implementation of the ST Stack does not care about the state of VBus. It starts immediately sending out source capabilities messages.I guess the problem is that PE Task is started immediately on Attach event in USBPD_DPM_CADCallback. And it never checks for the bus voltage. I composed a crude minimal example that does not even do anything when it should enable VBus but still source capabilities message is blown out immediately. Please find the minimal example attached. Did I miss anything? Will I need to find a workaround or can we get a fixed version of the library?Best regards,Adrian

Hello stm community. I am working on a project involving STM32H7 series MCU with Raw LCD panel of 24 bits. Since the display has no IC i am using the internal LTDC component to drive the lcd. So i have some questions can i drive the lcd backlight with My STM board or i just give some voltage to it . Some lcd says it needs 16 v power supply. Is there any complications in this and is it possible to do this way drive a Raw parallel 24 bit lcd with stm32 without lcd IC. give some expert opinions.

The serial port 1 code generated by the latest STM32CubeMX 6.13.0 will print garbled characters, and using the serial port routine UART_Printf in STM32Cube_FW_H7_V1.12.0 will also print garbled characters. It doesn't work when using the serial port routine UART_Printf in STM32Cube_FW_H7_V1.11.2. After comparison, there is a difference here. I can’t understand the function here. I will be careful whether changing it will affect other functions. *This post has been translated from Chinese to comply with the ST Community guidelines.

Hello!As the title suggests, the demonstration program is generated from the options shown in the following figure.After the program is burned onto the board, it won't run. It enters the debug mode and stops at the "SystemInit" point. After clicking continuously several times, it will then enter the "main" section.Any help would be appreciated as I am losing hair over this haha. 

This is to turn on MOSFETs that operate above 5.2V supply of the Boost regulator.  I have followed a forward converter guidance roughly in one of the application notes, but I have not used a transformer but placed a high value resistor in the voltage doubler output.  How much can I reduce the resistor values R6 and R69 without disrupt the operating of the SPV1040?  Reducing them to 1 to 10K would be good.  The input is limited to 4.5V so that a diode is not required between LX and Vout.  The application is a generator start-up circuit for vintage/veteran car dynamo.An Engineers Perspective: Vintage and Veteran Car dynamo power management Thanks

Post edited by ST moderator to be inline with the community rules for the code sharing. In next time please use </> button to paste your code. Please read this post: How to insert source code. Hello! I connect one I2C target and one I3C target device both to PB6/PB7,  which is configured to be "mixed I3C and I2C bus" through STM32CubeIDE. I3C parameter configuration is as below: /* USER CODE END I3C1_Init 1 */ hi3c1.Instance = I3C1; hi3c1.Mode = HAL_I3C_MODE_CONTROLLER; hi3c1.Init.CtrlBusCharacteristic.SDAHoldTime = HAL_I3C_SDA_HOLD_TIME_1_5; hi3c1.Init.CtrlBusCharacteristic.WaitTime = HAL_I3C_OWN_ACTIVITY_STATE_0; hi3c1.Init.CtrlBusCharacteristic.SCLPPLowDuration = 0x18; // 5MHz hi3c1.Init.CtrlBusCharacteristic.SCLI3CHighDuration = 0x18; hi3c1.Init.CtrlBusCharacteristic.SCLODLowDuration = 0x7b; //1MHz hi3c1.Init.CtrlBusCharacteristic.SCLI2CHighDuration = 0x7b; hi3c1.Init.CtrlBusCharacteristic.BusFreeDuration = 0x69; hi3c1.Init.CtrlBusCharacteristic.BusIdleDuratio

I'm trying to get a Raspberry Pi DSI display working with a custom board using a STM32MP157F. From the wiki I have the following. &dsi { status = "okay"; ports { port@0 { reg = <0>; dsi_in: endpoint { remote-endpoint = <&ltdc_ep0_out>; }; }; port@1 { reg = <1>; dsi_out: endpoint { remote-endpoint = <&bridge_in>; }; }; }; bridge@0 { compatible = "toshiba,tc358762"; reg = <0>; vddc-supply = <&reg_rpi>; status = "okay"; ports { #address-cells = <1>; #size-cells = <0>; port@0 { reg = <0>; bridge_in: endpoint { remote-endpoint = <&dsi_out>; }; }; port@1 { reg = <1>; bridge_out: endpoint { remote-endpoint = <&panel_in>; }; }; }; }; }; / { panel-rgb { /* Unknown; use a reasonably similar one */ compatible = "powertip,ph800480t013-idf02"; power-supply = <&reg_rpi>; status =

Hi,Im new to STM and trying to use 1 adc with DMA with 2 input and reading value.Board :STM32H753XI  EVALADC 1 :INP0 rank 1INP1 rank 2Functions : void adc_dma_multi(void)void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* hadc) Results :I tried to swap rank between INP0 and INP1 to check if my second entry was read correctly and there were no hardware problems, and the result is the same: rank1 is read correctly but rank2 = 0. I have attached main.c and IOC. 

I have four languagese/translation with their translations in TouchGFX DesignerIs there a way to reorder them? I would like to have IT GB ESP FR

Hi all,Im using STM32F410 uart 1 to transmit and receive.I use DMA to transmit bytes. I then use TC interrupt to send a break,then push an event to an event queue to signal that the transmitter is free.void interface_uart_tx_eot_isr(if_uart_t* p) { if (p->tx_last_in_chunk) { // Transmit break at end of tx work LockFromISR(); p->uart_dev->usart->CR1 |= USART_CR1_SBK; UnlockFromISR(); // register event for more tx data p->transmit_empty_handlerI(p->event_source); } }On the same uart I use DMA in circular mode to dump incoming bytes.Im using framing error interrupt to wake up a worker to deal with the received data.For the sake of this explanation, I have three stm32f410 devices connected in a ring1Tx -> 2Rx, 2Tx -> 3Rx, 3Tx -> 1Rx.So it is possible for, eg, device 2 to be recieving data as it is sending data.This is working well except:I find occasionally that I am missing a break interrupt and I'm pretty lost figuring it out.Oscilloscope shot uart_brea

Hello, I have a problem with a STM32L431CC generating a circular PWM burst with the DMA. I am using the Timer1 to generate 4 PWM signals on the Pins PA8, PA9, PA10, PA11. The systemclock of the Timer 1 is 80 MHz. The frequency of the PWM signal should be 20kHz. I have attached the code snipped were i configured the GPIO, Timer and DMA in the software. I get no PWM signal from the GPIO pins. When I manipulate the CCRx registers of the Timer1 with the ST Link debugger, I am able to generate PWM signals with the correct frequency and duty cycle. I suspect that the Timer1 do not make a DMA request and I am not able to find the failure. The DMA do not set any interrupt flags. Also when I manipulate the DMAR register of Timer1, I can see a valid PWM signal. Would be great when someone can support me Thanks Patrick     #define TIM1_PSC_INIT 0u #define TIM1_ARR_INIT 3999u /* ~20 kHz at 80MHz systemclock frequency */ #define TIM1_RCR_INIT 0u uint16_t volatile tim1_dma_buffer[] = {

I flashed firmware that sets. Now STM32Cubeprogrammer refuses to connect to the STLINK portion.How to recover from this / debrick the boards ? I tried pulling up PA14 / boot0 pin with a pull-up to CN7 pin 7, but no such luck...