Solved

Everyone, I would like to tell you. I will use the HAL library for the first time. What functions should be called in the main loop for write commands and read commands from I2C-Master? I am very happy if you can provide a sample source. I saw the source file made with STM32CubeMX, but I did not understand.

Hello,for Maintenance purpose, I made a .c library folder outside of SPC5Studio projectso I just linked the library folder under source folderbut my library didn't compiledHow can i add external library file into project?Thank you

for SPC58NE series.I know that Ethernet uses SPI protocol with MCU, but It's helpful if there're examples

I am using a SPC56XL70.

So I've just bought a F722ZE based board which is ideal for the projects I'll be working on, however I was hoping I could get this to work with the arduino IDE and save myself the trouble of learning the new platform, but this doesn't seem to be possible...What's the best free software available to get started with this board? Preferably with some examples, I've tried Keil but it's not compatible with the board I'm using. There must be something out there?

Thank you in advance.I am trying use two stm32f103c8t6 to do communication stuff. One is used to be transmitter and another is receiver. The code is simple but it doesn't work. Source code as follows:Transmitter:while (1) { uint8_t tran[4] = {0x21, 0x48, 0x59, 0x00};  HAL_UART_Transmit(&huart1, tran, 4, 10); HAL_Delay(100);}Receiver:while (1) { HAL_UART_Receive(&huart1, tran, 4, 10); HAL_Delay(100); }The baud rate is set to 115200 bits/s. I use usb-to-ttl to check the situation. The transmitter is working normally, but the receiver cannot receive the normal data as expected.Please help!!!

 the MCU stm32L011F3 has only 8k flash ,and without standard peripheral library, only HAL and LL library, as i know, the Optimization of HAL is lowest all of them, and LL driver is little Readiness,can any one tell me, is that the HAL driver can execute successfully in stm32L011F3 ?thanks a lot!

​Hi.​I changed the debugging tool from IAR to trueSTUDIO for STM32.​There is code that IAR created and completed the operation. However, the same code, but does not work in trueSTUDIO.​An example of the code is shown below.​int a = 0;​void HAL_TIM_PeriodElapsedCallback (TIM_HandleTypeDef * htim){ a ++;}​void example_function(){  a = 0; while (a <3) {    asm volatile ("NOP"); }}​int main(){ example_function(); while(1) { }}​​I found the cause with a breakpoint in trueSTUDIO, and I can not get out of the while statement with the code below. asm volatile ("NOP");​What is the difference between IAR and trueSTUDIO?​What is the solution to this situation?​

Need to generate a repeating waveform with external SPI 16-bit DAC.Using a table of values in memory, repeatedly loop through table outputting values to DAC.Delay between outputs is constant. No glitches at repeat!DMA only (no interrupts).What's the most effective way to do this with ST32F427?Thanks,Best Regards, Dave

I am working with M24M02 and I measured that it takes 50% longer to read a page than to write a page. Is this normal that read time exceeds write time?  NOTE: This question and answer originated from a customer support case which was handled by us. We regularly review support cases and add any helpful ones here for all to benefit from.

I have been asked to embed an accelerometer into the engine control module. It would normally be used when the engine is not running to determine static angle with respect to gravity; low G, angle sensor. However, once the engine starts running there will be significant vibration, the controller is mounted to the engine. For discussion purposes it may be considered 10 g random, up to about 3000 Hz. The specification indicates the normal operating ranges and then indicates a couple of shock type accelerations (absolute maximums). But these are very short duration (3000 g, 0.5 ms) or (10000 g for 0.1 ms).Which of your MEMS devices would you recommend if exposed to continuous 10 g random vibration? 15 g? 20 g?NOTE: This question and answer originated from a customer support case which was handled by us. We regularly review support cases and add any helpful ones here for all to benefit from.

Hi​, I'm using LIS2DS12 and I was wondering if it was possible to use it as a pedometer? How do you suggest to set the thresholds?Thanks​

Hello. I have custom board with STM32H743 and USB3320 in Full Speed Mode. Dont have problem with initialization of MSC (Window read descriptor, configuration and other). But when read blocks from SD card some trouble occurs. With USBPcam and Wireshark I check than Windows read data from SD card in next sequnce: Sector 0 Size 512, Sector 0 Size 512, Sector 2 Size 512, Sector 0 Size 512, Sector 63 Size 512. When reading sector 63 problem occurs: data from STM32 transmitted but on PC dont received.In debug I see that Sector 63 read success and USB_Transmit function also call. Maybe someone have suggestions to resolve this problem?

i bought new ST25RU3993-EVAL board. ST25RU3993 Reader suit is installed. Powered on the board through USB cable. ST25RU3993 reader board is connected to ST Reader suite Tool. clicked on start scan on tool. Placed the Tags in-front of Antenna port .But unable to detect the tags. In this board antenna is not given. is ST25RU3993-EVAL board detect the TAGS without Antenna ? 

I migrate my CubeMx project that is based on stm32l072cbtx to version 5.0.1 but in connectivity menu, LPUART1 NVIC settings doesn't appear. So I can't enable LPUART1 interrupts with code generation. Is there any problem? or I've missed something

We are trying to evaluate ST25R3911B for our application. I have installed STM32CubeExpansion_NFC5_V1.3.0 Library. I tried an example code for STM32L476RG-Nucleo from this library (\STM32CubeExpansion_NFC5_V1.3.0\Projects\Multi\Applications\Polling\SW4STM32\STM32L476RG-Nucleo\STM32L4xx-Nucleo-Polling). I can see the tag type & ID on serial terminal as shown in image. Now I am trying to read & write the memory block of tag. But unable to find the API sequence necessary to perform read/write. can anyone please suggest?

hii have a problem when i generate a code by cubemx v5 ,i have a problem for my stm32h7 board.mcu wait at this line and can't init voltage regulator well, and wait on this infinity loop./** * @brief System Clock Configuration * @retval None */ void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};   /**Configure the main internal regulator output voltage */ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);   while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) { }i use debugger and saw at this loopwhile ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) { }mcu can not run over this while code.i check register value of this code and this result:PWR->D3CR=0x0000C000PWR_D3CR_VOSRDY=0x00002000if i comment this lines my mcu continue init routinevoid SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitS

Dear technical support I'd like to notify you that seems that there is an error in you CUBE version 4.24 until the latest one 5.1 (i checked one by one and there is an error with the DMA RX in circular) Before (with previous CUBE versions) I was using the Nucleo-STM32F767ZI and I was able to communicate continuously through the UART 8 in DMA mode (circular RX). However, now that I updated my .ioc file to the newest CUBE versions I'm not able to continues receive information in Rx, i.e. it only receive the information in Rx one time and the values are not updated (values sent by an external terminal), then if I press the reset button on the Nucleo board the value is updated. It doesn't matter if I select Rx as Normal or Circular mode, there are not changes at all. I'm attaching my CUBE file to take a look, I have to mentioned that I downgrade the version (Cube 4.24) in order to see if the problem was with the version Cube 5.1 but still the same not able to have changes wi

Posted on June 20, 2018 at 15:33Hi All,I'm developing an application using CubeMx to generate the basic code. On CuebMx I enabled freeRTOS and LWIP.Now I would like debug my threads but Eclipse gives me access only on the thread in esecution before the break/stop.Someone (knows and so) can give me a link or the tips to enable on Eclipse  the view of all threads allocated?Thanks... for any help.Gianluca

I've been trying to adapt an example piece of code that utilizes a UART from the Visual GDB website. The adaptations are:Using an STM32F769 Discovery board.Communicate with an ESP8266 device plugged into the board's WiFi socket.I managed to work out that I need to use UART5 and PD2 as the UART's RX and PC12 as the UART's TX.The serial details are the same as the example so need to alter those.Well when I run this code the send appears to do something because the blue data LED on the ESP8266 flashes briefly (during the send) so this tells me either the send is working or at least the TX pin is fluctuating in some way.However the receive hangs, the only to stop it hanging is a finite timeout or pass 1 as the buffer length. When I pass 1 as the length I can see that it does indeed write to the buffer and in fact writes a 0x00 but nothing more.Repeated receives hang, so trying to receive 1 byte then again trying that leads to a hang, only the first read of 1 byte ever returns (with an OK s

I think I've caused some problem in the way I'm coding this interrupt. For a second I thought it was a pipeline re-entry problem like Clive-Two-Zero described in a different thread, but adding a volatile variable and incrementing it, didn't seem to work.Does anyone see anything obviously wrong with the code? This is a project generated from TouchGFX and I'm using GCC to compile. I was unsuccessfull in porting the project to System Workbench or Atollic to take advantage of the in circuit debugger to see exactly what is happening and where it's hanging.Left and Right comes from a different microcontroller that is handling a quadrature encoder dial. So I know the signal are nice and clean of bouncing (checked with scope). What made me sure it was the interrupt is when I move the left and right output from the microcontroller handling the quadrature encoder to the joystick left and right input of the discovery kit (STM32L4R9I-DISCO), the behavior goes away and I get nice and responsive gra

I am using a stm32f407 and i use this code inside a loop:/* Mount SD Card */ if(f_mount(&fs, "", 0) != FR_OK) _Error_Handler(__FILE__, __LINE__); /* Open file to write */ if(f_open(&fil, "first.txt", FA_OPEN_ALWAYS | FA_READ | FA_WRITE) != FR_OK) _Error_Handler(__FILE__, __LINE__); /* Check free space */ if(f_getfree("", &fre_clust, &pfs) != FR_OK) _Error_Handler(__FILE__, __LINE__); total = (uint32_t)((pfs->n_fatent - 2) * pfs->csize * 0.5); fre = (uint32_t)(fre_clust * pfs->csize * 0.5); /* Free space is less than 1kb */ if(fre < 1) _Error_Handler(__FILE__, __LINE__); /* Writing text */ sprintf(counter_buff, "%.10f", count); f_puts("\n", &fil); f_puts("STM32 SD Card I/O Example via SPI\n", &fil); f_puts(counter_buff, &fil); f_puts("\n", &fil);   /* Close file */ if(f_close(&fil) != FR_OK) _Error_Handler(__FILE__, __LINE__); /* Open file to read */ if(f_open(&fil, "first.txt", FA_READ)

I'm having a lot of trouble finding documentation. This board sold by ST exposes a connector that is intended to house an ESP8266 WiFi device. But the ST documentation says nothing about how that connector is wired on the board. I assume it's tied to one of the USARTs but which one?Are there any examples of C/C++ code for this board that interacts with the ESP8266?Given that ST refer to the WiFi device and designed a socket and support specifically for it, it's odd that I can find virtually no information.Any help is greatly appreciated.Hugh

Hi,I am using a LSM6DSO accelerometer. I want to know what type of acceleration I am getting as output: RMS acceleration or just the acceleration amplitude?Regards,Gabriel

I created a TouchGFX project for the STM32429I-EVAL1 board in CubeMX 5.0.1. I configured all the peripherals needed and verified that the LCD and SDRAM are working correctly. After generating the code in CubeMX I also generated the code in TouchGFX.It seems however that TouchGFX does not draw to the framebuffer address (SDRAM). The values do not change and remain static. Am I missing something to make this work? I included the .ioc file for creating the project.