Solved

Hi, I'm running the following example project:STM32Cube_FW_F7_V1.17.0\Projects\STM32F769I-Discovery\Applications\mbedTLS\SSL_Clienton the development board STM32F769I-Discovery.Seems like the application uses the .h file STM32Cube_FW_F7_V1.17.0\Middlewares\Third_Party\mbedTLS\include\mbedtls\config.hto configure the embedTLS module.The project also includes this .h file for configuration of mbedTLS:STM32Cube_FW_F7_V1.17.0\Projects\STM32F769I-Discovery\Applications\mbedTLS\SSL_Client\Inc\mbedtls_config.hBut it doesn't seem like it's used, why is that? BRJonas 

STMicroelectronics ST-LINK GDB server. Version 7.3.0Copyright (c) 2023, STMicroelectronics. All rights reserved.Starting server with the following options:Persistent Mode : DisabledLogging Level : 1Listen Port Number : 61234Status Refresh Delay : 15sVerbose Mode : DisabledSWD Debug : EnabledWaiting for debugger connection...Debugger connectedWaiting for debugger connection...Debugger connectedWaiting for debugger connection...-------------------------------------------------------------------STM32CubeProgrammer v2.13.0------------------------------------------------------------------- Log output file: C:\Users\rahgi\AppData\Local\Temp\STM32CubeProgrammer_a16228.logST-LINK SN : 022604157316303030303032ST-LINK FW : V2J45S7Board : --Voltage : 3.16VSWD freq : 4000 KHzConnect mode: Under ResetReset mode : Hardware resetDevice ID : 0x410Revision ID : Rev XDevice name : STM32F101/F102/F103 Medium-densityFlash size : 64 KBytesDevice type : MCUDevice CPU : Cortex-M3BL Version : -- Mem

hi guys, I'm a desktop programmer and do not know much about micro controllers and electronics but i am very interested in making an oscilloscope  which:- simple to build with well known parts and ICs- it uses bluepill as the ADC and no other ADCs- it be able to measure negative voltages- It uses near maximum  ADC sample rate possible from bluepill  Single channel would be enough for above spects. recently I was working with a cool project named rp2daq which convert RPI Pico to a 500KSps /12Bit resolution and uses USB to send data to PC.I did try to make a proof of concept version of a oscilloscope on top of it and it did worked (kind of) available from here.I was using this simple oscilloscope since last day which i gave 10v signal to it's ADC by mistake and it broke.The pico is expensive relate to blue pill (in my area, 3x more expensive), so i am thinking if anyone interest in making such open source scope, i think I can fully do the desktop part and need he

Hello all,for my DIY Radio Controller (LoRa and STM32F1C8) i am using two joysticks and one poti.I am reading ADC with the DMA but what i noticed is that the ADC values are not so accurate.I know with not (professional, expensive) Potis and joysticks this accurate is almost impossible.With 12 bit resolution the ADC value is (0 - 4095) but the problem is that sometimes the tolerance gets more then 20 or 30 and this value is not ignorable for RC.P.s. the wires from Joysticks and poti are about 10cm long.My question :Is there any idea or way to get more accurate readings from ADC? some filtering or anything else.Would be using switching regulator as Vcc problematic? Please if you have some tipps or ideas it will be appreciated.Thank you in advance.

Welcome to everyone!This question concerns the STM32F103CBT6 microcontroller , I have given a "BluePill" module equipped with this microcontroller. When I download the hex or elf file with STM Programer, it downloads nicely, no problem, But! however, it catches itself without any precedent and locks itself, and a message appears that it is only available in Reset mode, the program meter is no longer connected to the microcontroller. Could this be eliminated somehow, so that whenever I want to download something, can I do it without any problems? There should be no microcontroller "locking", etc. . Thank you very much in advance for your help Everyone!

We are following the steps mentioned in this link How to measure the DDR throughput - stm32mpu.However , stm32_ddr_pmu.py is not found anywhere Please point us to stm32_ddr_pmu.py.

I can't erase the flash in the STM32L552CCT6 with the code below. I wonder if my code is wrong. When I check the memory, the 2kB from the flash address 0x803F800 is not 0xFF. The reason it wasn't 0xFF originally seems to be because something other than 0xFF happened to be written during debugging.Thank you. uint32_t error; uint8_t ram[2048]; HAL_FLASH_Unlock(); FLASH_EraseInitTypeDef flash; flash.NbPages = 1; flash.Page = 127; flash.TypeErase = FLASH_TYPEERASE_PAGES; flash.Banks = 1; if (HAL_FLASHEx_Erase(&flash, &error) == HAL_OK) { HAL_FLASH_Lock(); if (error != 0xFFFFFFFF) return false; else { if (keepRamData == false) memset(ram, 0xFF, 2048); return true; } } HAL_FLASH_Lock(); return false;Code formatting applied - please see How to insert source code for future reference.

Hi! I am looking for help with my own PCB design first running process. I have PCB with STM32F407VG and LAN8742A PHY. I lost the whole day trying to run it without any effect. After powering on, the orange LED is on constantly, and nothing else. I tried it with the program, and the behavior is the same with an erased chip. I have attached schemat parts, clock configuration, and the board state photo.I tried to set multiple clock configurations, but nothing came up. Maybe I need to add some power sequence at the start of the MCU. I tried many configurations of reset line and the same effect, just nothing. I don't have any idea what I should do more.I will be grateful for any help and suggestions! Thank you so much for your attention and participation.

I'm just getting started with my STM32WB15CC nucleo board, and my first goal was to put in shutdown mode to check the current draw, which I expected to be around 1 uA. I'm measuring the current on the JP3 header with a joulescope which should represent the actual current used by the MCU itself.I'm using the PWR_LPSLEEP example in the CubeMX IDE, and exchanged the "entersleepmode" call to the "enter shutdown mode", see below: /* Enter Sleep Mode, wake up is done once User push-button (SW1) is pressed *///HAL_PWR_EnterSLEEPMode(PWR_LOWPOWERREGULATOR_ON, PWR_SLEEPENTRY_WFI);HAL_PWREx_EnterSHUTDOWNMode(); After the shutdown call, the joulescope shows a current draw of 42 uA, which seems very high for shutdown mode.Am I missing something? Any pointers?The reason I want to start with this basic test is because the project I'm working on is for a battery driven sensor, so a low current is crucial.

Hi,I've a project that has quite a lot of peripheral configurations, plus code, based around Nucleo H755.Now I need to port this into a new project based on the same chip (STM32H755ZIT6) but targeting my own board design. I will be using the same peripherals.Is there a convenient way to migrate the project in CubeIDE without having to painstakingly re-enter all of the .ioc's configuration parameters in a clean project?Copying the code over is easy enough, it's just stuff relating to the BSP that I see as problematic.Having previously played with editing the ioc file manually I concluded that this is not a good way forward (and I'm aware that it's not recommended).Thanks

Hello,I originally tagged onto this thread: https://community.st.com/t5/stm32-mcus-products/stm32f103-hse-crystal-capacitors/td-p/771200 but I was recommended to make a separate thread. Many of the STM32 datasheets, such as the STM32H753, say that the pin capacitance is 5pF per pin. When trying to size a crystal for the HSE oscillator, the designer is told to follow AN2867. When trying to calculate the stray capacitance we (at a minimum) add the pin capacitance of the two oscillator pins to get 10pF. The STM32H753 datasheet even says to approximate 10pF here on page 232:AN2867 does not recommend any crystals for the STM32 HSE oscillator, so the assumption is that crystal has to have higher than 10pF load capacitance for STM32 devices. I understand that pin capacitance would vary per package. Does ST have a more accurate estimation of pin capacitance? Or does ST have recommendations for crystals for the STM32 HSE oscillator?Thanks,Nino

Hello Which are the correct Capacitors to use for HSE on STM32F103 with the following Crystal?Frequency: 8 MHzLoad capacitance CL: 20 pF Thank you in advance for a quick hint.RegardsMichael 

Posted on July 10, 2018 at 14:37I've been designing sub-gram boards for data logging on songbirds using the stm32l432.  Although mostly I use ultra-low power external RTCs, I recently built a test board using a 4pf 32768 crystal.  The question was then how to determine the load capacitors.  After reading the relevant ST appnote and stm32l432 datasheet I assumed that the pin capacitance was ~5pf and, given the simple board, minimal stray capacitance.  This suggested 3pf load capacitors((4-5/2)*2) and a load error of 1.5pf without capacitors.   With a predicted error of 125ppm/pf, I thought it reasonable to try without any additional capacitors in the hopes of saving board real estate in the final design.  I did include capacitor footprints for my test board.   Upon testing, I found an error > 800ppm which was surprising for two reasons -- it suggested a much larger load error than 1.5pf and also made clear that the formula for predicting

Hello, I'm using an STM32H750VB and am trying to use the HSE crystal to communicate over USB to my computer, but it isn't able to connect to my computer. I suspect that the issue lies with the crystal since I tried to probe it with an oscilloscope and wasn't able to get any sort of reading. Additionally, when I run a timed LED blinking code using the internal oscillator, it works properly, but when using HSE it doesn't blink. I attempted to calculate the values of the capacitors based on the crystal load capacitance of 8pF. Based on the image of the circuit and crystal parameters does it look like there is an issue with compatibility or component values?   

Hi,I have developed custom board with STM32C071CBT6. I configured USB port with USBX in CDC mode. I configured USB device descriptor values as below: When I connect host Windows 11 PC to my custom board, device manager on PC shows - USB Serial Device(Comxx). It does not show product string as 'STM32 Virtual ComPort'.Please help debugging this issue.Thanks,Pradeep

Today, after updating the latest IDE, my interface has changed to this look (Figure 1), which makes me very uncomfortable. How can I change it to the previous look (Figure 2)?

Did I miss the memo?  

Hello, i am looking into doing wireless thermostats using Zigbee who communicates with controlers. The controlers activate and desactivate valves to heat the house. What would be the configuration of the microcontrolers and how can i program my application. its a custom circuit board i have made i only need to configure and program. I have activated the STM32_WPAN and i dont know how to configure the Zigbee after i activate it, i cant find applications on the internet.Thank you!

I recently purchased a VL53L7CX and VL53L8CX, so I wanted to test the Motion Indicator functionality for each zone to show if the targets moved and how they moved via SPD of the software by STM except that there, when two people present themselves in front of the sensor, we only see one personHow to do it?

DCMIPP_ContinuousMode_FSBL - DCMIPP_ContinuousMode_FSBLReading project nodes...DCMIPP_ContinuousMode_FSBL.outError[Lt006]: Incompatible object(s): evision-awb.o(libn6-evision-awb_iar.a) and 2 other objects in libn6-evision-awb_iar.a and 2 other libraries use VFP instructions incompatible with No vfp (provided as FPU option)Warning[Lt049]: Potential floating point parameter passing conflict. The first module below references the second and they have been built with different settings.AAPCS, base variant: isp_algo.oAAPCS, VFP variant: evision-st-ae.o(libn6-evision-st-ae_iar.a)Warning[Lt049]: Potential floating point parameter passing conflict. The first module below references the second and they have been built with different settings.AAPCS, base variant: isp_algo.oAAPCS, VFP variant: evision-awb.o(libn6-evision-awb_iar.a)Total number of errors: 1Total number of warnings: 2Resolving dependencies...Build failed

Hi all,I'm struggling to get the ST bootloader on a STM32L431KUB to communicate with a STLINK-V3SET via CANBUS using the STM32CubeProgrammer, the reported error is ST-LINK error (BRG_CAN_ERR) Establishing connection with the device failed.I have made an adapter board with a MCP2551 transceiver which is connected via flying leads on CN9 of the STLINK-V3SET. I can connect a CANBUS analyzer to the output of this and see that the STLINK is sending messages to id 0x79, so I am confident this is working as expected.My target is a custom PCB with an 8Mhz external clock and a TCAN322 CANBUS transceiver, which functions correctly when I load my application software through the SWD interface.  I can also see that the uC is going into the bootloader when the BOOT0 pin is pulled high or the device memory is blank, by using the SWD interface and checking the program counter is in the 0x1FFFXXXX range.  However despite seeing the expected messages on the CANBUS and seeing ac

So I know if I use the STM32CubeProgrammer there's an option to skip flash erase before programming which is great. However, I'm trying to debug some code and I need to prevent flash erase, because I have some code in a sector which I need to keep, but also program some new code in that same sector.By using the 'ST-LINK_gdbserver --help' command, there's no option/argument which I can use to prevent the flash erase before programming. I tried using the '--skipErase' option mentioned here:https://community.st.com/t5/stm32cubeprogrammer-mcus/skipping-flash-erase-with-stm32-programmer-cli-and-stlink-v3/td-p/608809  But it didn't work for me:'/opt/ST/STM32CubeCLT_1.18.0/STLink-gdb-server/bin/ST-LINK_gdbserver -p 50000 -cp /opt/ST/STM32CubeCLT_1.18.0/STM32CubeProgrammer/bin --swd --halt --skipErase -m 0PARSE ERROR: Argument: --skipEraseCouldn't find match for argument' It seems like the --skipErase command is specific for the programmer, but there's no way to invoke it from t

I want to use the STM32F407 to implement the NanoEdge AI Library for Anomaly Detection (AD) tasks.The documentation mentions nanoedge.ai's method for backing up and restoring the library knowledge using the .ld file in a Linux environment. I want to know how to perform this backup operation in Keil.

Hi all  I am trying to understand how can I send data and recieve ,,Can you share any example code or something. I am sharing my project can you so confirm me is configuration is correct. B.R Ashish