Ask questions on STM32CubeIDE. Discuss how to build, debug, configure, and optimize your project as well as how to use our software tools.
We are pleased to announce that the release 1.19.0 of STM32CubeCLT is available. What is new in 1.19.0: Support for ST Arm Clang toolchainMaintenance of the previous versionUpdated in accordance with STM32CubeIDE v1.19.0 Main fixed issues in 1.19.0: ...
Updated post to reflect permanent fix Dear STM32CubeIDE user, Further to the recent STM32CubeIDE project creation issue, we would like to inform you that a solution is now available for you. This permanent fix applies to all STM32CubeIDE versions. I...
We are pleased to announce that the release 1.19.0 of STM32CubeIDE is available. What is new in 1.19.0: Microcontroller, microprocessor, and board lists aligned with STM32CubeMX v6.15.0:Added the support for STM32MP21xx microprocessors to the STM32MP...
Starting from the release in November 2025, STM32CubeIDE and STM32CubeMX will be available exclusively in their standalone versions. STM32CubeMX will no longer be integrated inside STM32CubeIDE. Instead, the two tools will be interoperable in the sam...
Post edited by ST moderator to be inline with the community rules especially with the code sharing. In next time please use </> button to paste your code. Please read this post: How to insert source code# STM32CubeIDE ETH Configuration Bug Report ## ...
Hello,I cant start SDRAM to work, I ques what FMC controller do not initialize interface correctly because CLK is dead (bug !?), there is no activity at all, I connected oscilloscope to CLK output to check, if I toggle manually the pin PD9 (FMC_SDCLK...
Hi!I try to read data from an I2C device using DMA. I use a STM32-F412ZG nucleo board.First I try to write without DMA : HAL_FMPI2C_Mem_Write(&hfmpi2c1, 0x52, 0x7fff, FMPI2C_MEMADD_SIZE_16BIT, tab, 1, 1000); Then I want to read data using DMA with: ...
Hello,Since I installed a new version of linux mint (22.2), I can't upload my programs to the MCU.CubeIde show this error: Could not determine GDB version using command: arm-none-eabi-gdb --versionarm-none-eabi-gdb: error while loading shared librari...
Follow-on from: Help for porting from MDK to CubeIDE.HiI am now working on porting an MDK example to CubeIDE on an F767-based customized board with 32MB SDRAM and an LCD interface.At the moment, the build of the ported example in CubeIDE gives follow...
HiI am trying to port an example application from MDK to CubeIDE, the CubeIDE does not give me correct compilation result:1. It completes the compilation when code contains syntax error and it produces binary. This is quite different from past experi...
I am working to send data continuously using TCP/IP, LWIP and free-RTOS. I created three tasks and using one task to send data. Each data packet is 1460 bytes and after sending around 300K packets the system halts and resets. I wanted to increase the...
Hi there, Could anyone advise how to setup STM32CudeIDE to debug my custom board using ST Link V2 ? https://www.amazon.sg/SFCPI-Programmer-Microcontroller-Interface-Simulatio/dp/B09Q22M9CK/ref=sr_1_10?crid=30DWFY0GZDYLG&dib=eyJ2IjoiMSJ9.qqFD5Om07FW...
Weird things are happening.The breakpoint i set in the void Read_ToF_From_VL53L0X_FreeRTOS_Task(void *pvParameters) task is not getting hitthis task calls VL53L0X_Measure_Distance function in which i set a breakpoint which is working ok ! also i pu...
When I build and debug my project, I get the error window below when the debugger connection is established. The download takes place and verifies successfully, but displays the message again.However, when I start program execution, the console displ...
