Nucleo-n657x0-q: CubeProgrammer Can't connect via ST-LINK or UART
Hii have issue with my nucleo -n657x0-q board, i couldn't connect to it neither ST-LINK or UART the Boot0,Boot1 jumpers are 1,0 respectively. Any idea?
STM32 MCUs Boards and hardware tools
Ask questions and find answers on STM32 hardware set-ups, including schematic-related challenges, debugging probes, power configurations, and more.
Forum Posts
Resolved! Unable to connect to STM32F103TBU with ST-Link
Hello all, I have been working on a keyboard PCB with an STM32F103, and I have started trying to program it with the STM32duino bootloader however, I have been unable to connect to the chip. This is my first time using the STM32CubeProgrammer with an...
NUCLEO-U5A5ZJ-Q - USB port configured as host
Hi everyone. I have a problem with my U5A5ZJ-Q core board. The mounted microcontroller is STM32U5A5ZJT6QU. The project is to drive a QUECTEL em05 LTE modem. I need to configure the USB port exposed by PA11 and PA12 in Host mode. I am using the standa...
Resolved! STM32C011F6U6 Flash using UART System Bootloader
Hi everyone,I’m working with the STM32C011F6U6 in my design and would like to flash it using the system bootloader (USART1 on PA9/PA10 as described in the datasheet).Before finalizing my design, I ordered the MB1684B board with the STM32C011F6U6 to t...
Resolved! Can't receive bytes through the Nucleo MB1404 - STM32HM563ZI USART2
I've created a project for my Nucleo MB1404 - STM32HM563ZI board which uses USART2 and USART3 to send and receive data to a computer. I've just configured both UARTS in the same way with the same parameters with STM32CubeMX. The USART3 works without ...
Resolved! NUCLEO-C051C8 -- Altium project files
Hi, I am reaching out to kindly request NUCLEO-C051C8 project files ( It seems that ST uses Altium).Altium files would greatly facilitate my development.Please help me.
RTC Initialization Fails Using External LSE on STM32F407G-DISC1
We are testing the STM32F407G-DISC1 development board and trying to use an external 32.768 kHz LSE oscillator for RTC clock source. Since the onboard crystal footprint was empty, we manually soldered the following components on the LSE pins (PC14 and...
Can't get maximum ADC samples mentioned in datasheet using STM32H743ZI2 USB FS
Guys currently I am working on STM 32 H7 board and trying to achieve 3.6MSPS as per mentioned in an datasheet, after many tries currently I can able to take 175k samples/second as 12 bit resolution ADC values using an USB FS but if they claimed to be...
[STM32F411RE] USART2 data always goes to ST-LINK VCP instead of PA2/PA3 pins
Problem descriptionHi everyone,I’m working with a NUCLEO-F411RE board and I need to use USART2 (PA2=TX, PA3=RX) to communicate with a LoRa module (Reyax RYLR998).The issue is: even though I configure USART2 in CubeMX, all data I send ends up on the C...
Trouble with X-CUBE-ST67W61M1 with X-NUCLEO-U545RE-Q
I am trying to use X-CUBE-ST67W61M1 but I am failing to read any data with COM port set as document um3449 indicates (I am currently using a UART-TTL converter connected on CN7 of X-NUCLEO-ST67W61M1). I am trying to update the X-NUCLEO-ST67W61M1 firm...
