Power management

Discuss power management solutions. Ask questions and find answers on voltage configurations, short circuit protection, and programming.

cancel
Showing results for 
Search instead for 
Did you mean: 

Forum Posts

L7987 parts selection

HI Sir, "Could you please check the following switching frequency waveform images? The setup is: 24V input, 12V output (max load ~1.8A), R-FSW = 68kΩ, inductor = 15μH, and COMP configured as 680Ω + 33nF (parallel with 1nF) — see the images below. Thi...

PZha1_1-1766666083421.png DB32-24in-12out1.43A-R15 680ohm.png DB32-24in-12out1.02A-R15 680ohm.png DB32-24in-12out1.43A-R15 10K .png
PZha.1 by Associate III
  • 92 Views
  • 0 replies
  • 0 kudos

VNH9030AQ footprint / land pattern?

Hello -  I'm looking for a footprint or land pattern to use for designing a PCB around the VNH9030AQ.  I'm sorry if I've overlooked it somewhere--can anyone point me in the right direction? Thank you for your time!

gannet by Associate
  • 269 Views
  • 3 replies
  • 1 kudos

Lt spice model for SMA6T28CAY

Hi everyone,I am searching for LT spice model of SMA6T28CAY diode. can someone please help me to find this and integrate in LTspice application. Best Regards Vedanth.

vedanth by Associate II
  • 917 Views
  • 4 replies
  • 0 kudos

STPS5H100AF operating temperature?

Regarding the STPS5H100AF, the datasheet states that the storage temperature is -65 to 175°C, but there is no mention of the operating temperature.What is the operating temperature?

Ryo10 by Associate
  • 719 Views
  • 3 replies
  • 1 kudos

Resolved! Misleading statement about TS function of BQ25120A

Hi,Our development board uses BQ25120A for battery management.In the datasheet section 10.2.2.1 Default Settings, there is a statement:• If the function is not needed, connect TS to the center tab of the resistor divider between VIN and the ground.(p...

cyber_v1 by Associate III
  • 1224 Views
  • 6 replies
  • 7 kudos

SPV1050 sample time

The Tsample value doesn't reach the published value (between 0.3 and 0.5 s, and from my measurements between 0.3 and 0.35 s) until Vstore reaches the EOC threshold. Before, it is just around 80 ms. Once EOC is reached and when Vstore decreases again ...

mgasulla by Associate
  • 275 Views
  • 0 replies
  • 0 kudos

Resolved! STWBC2-HP and STWLC99 with STSC protocol

I am developing a solution using a STWBC2-HP tx running from a 24VDC supply to drive a STWLC99 rx and need to use the STSC protocol to achieve 50~100W. This is for bespoke power transfer rather than a conventional charger. I am basing the design on t...

NickA by Associate II
  • 1250 Views
  • 6 replies
  • 0 kudos

STPM801 with a I2t characteristic

In our application we use the STPM801 as a switch and fuse. The fuse characteristic is, by default, very linear (except some filter/blanking times). Is it possible to give the fuse a I2t characteristic like old fashioned fuses/thermal fuses?I did exp...

JTo by Associate
  • 338 Views
  • 0 replies
  • 0 kudos